Tyan S5535 Quick Installation Manual
- Category
- Wire connectors
- Type
- Quick Installation Manual
1
2
3
4
5
1 2 3
Top View
Without jumper
Jumper
Pins
1 2 3
Top View
With jumper installed
on pins 1 and 2
Insert the server board into the chassis. Attach the server board to the chassis by securing
the screws on the designated locations.
Apply the thermal
grease.
Install the CPU heatsink. Secure the heatsink screws.
1 2 3
Unlock the clips. Insert the memory module. Lock the clips.
1 2 3
Connect the
heatsink fan cable.
4
1 2
Open the socket levers.
Open the CPU Socket Cover.
1
2
Close the CPU Socket Cover.
5
Close the socket levers.
6
3
Remove the CPU protection cap.
4
Install the processor and make
sure the gold arrow is located in
the right direction.
Install the Server Board
Install the Processor
Install the CPU Heatsink
NOTE: To avoid
damage, do not use
torque force greater
than 7kgf/cm (6.09
lb/n) on each screw.
Install the Memory
Install the Power Cable
Locate the External I/O Ports
Jumper Cap On/Off DOA/ RMA Reminder
NOTE: Please save and replace the CPU
protection cap when returning the server board
for service.
CONNECTORS
1
LAN1 +USB2.0 (J42)
2
DP1 Connector (J10)
3
DVI-I Connector (DVI-I)
4
USB3.0/DP2 (J12)
5
LAN2 + USB3.0 (J9)
6
Audio Ports (J19)
7
Front Audio Header (FP_AUDIO_1)
8
Rear FAN (J17)
9
TYAN Module Header (DBG_HD1)
10
Front USB2.0 Header (FP_USB_3)
11
USB typeA Connector (J27)
12
Front USB2.0 Header (FP_USB_2)
13
SATA DOM Power Header (J81)
14
SATA 6G Connector (SATA_6G_5)
15
SATA 6G Connector (SATA_6G_1)
16
SATA 6G Connector (SATA_6G_3)
17
SATA 6G Connector (SATA_6G_2)
18
SATA 6G Connector (SATA_6G_0)
19
Intruder Header (INTRD1)
20
FP Header (J15)
21
BAT Socket (XBT1)
22
USB3.0 Header (J24)
23
Speaker Header (J83)
24
24 pin Power Connector (ATX24P_1)
25
COM Port Header (J77)
26
Front FAN (J20)
27
CPU FAN (J16)
28
PSMI Connector (J31)
29
ATX 4 pin Power Connector (J18)
SLOTS
A
PCIE x16 Slot (x16 link)
B
PCIE x1 Slot (x1 link)
C
PCIE x8 Slot (x4 link)
D
DIMM0 (A1)
E
DIMM1 (A0)
F
DIMM2 (B1)
G
DIMM3 (B0)
JUMPERS
a Clear CMOS Header (J4)
b ME Header (J2)
c Security Header (J1)
Motherboard Placement
Phillips Screwdriver Flat-head Screwdriver Anti-Static Wrist Strap
Required Tools
Package Contents (Retail Box Only)
Read Me First
1
. The motherboard User’s Manual is available for download from our Web site at http://www.tyan.com. Make
sure to read all precautions and instructions before you start installing the server board.
2
. Refer all servicing to qualified personnel to avoid the risk of damage to the server board.
3
. Exercise normal ESD (Electrostatic Discharge) procedures during system integration. TYAN/MiTAC
recommends wearing gloves and an anti-static wrist strap to avoid possible damage to the equipment.
4
. Current processor socket design places the pins on the motherboard instead of the processor itself. Exercise
extreme caution when installing the processors as the manufacturer’s warranty does not cover damage
inflicted upon the motherboard, including damage to the CPU sockets.
DP1
USB3.0/
DP2
LAN1/
USB2.0
Audio Ports
LAN2/
USB3.0
DVI-I
Driver's and
Utilities DVD x 1
Quick Installation
Guide x 1
SATA Cable x 5Server Board x 1 Rear I/O Shield x 1USB 3.0 bracket x 1
S5535 Quick Installation Guide
Document # D2242-100 / Revision 1.0
D
E
F
G
A
B
C
1
2
6
3
5
7
25
26272829
8 9 10 11 12 1413 1615 17 18 19
4
20
22
24
23
21
c
b
a
-
1
Tyan S5535 Quick Installation Manual
- Category
- Wire connectors
- Type
- Quick Installation Manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Tyan GT62H-B7106 Service Engineer's Manual
-
-
-
-
-
-
-
-
-
