TP-LINK AV200 User manual

TL-WPA4220

300Mbps AV500 WiFi Powerline Extender

TL-WPA2220

300Mbps AV200 WiFi Powerline Extender

REV1.0.2

1910010839

COPYRIGHT & TRADEMARKS

Specifications are subject to change without notice. is a registered trademark of

TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered

trademarks of their respective holders.

No part of the specifications may be reproduced in any form or by any means or used to make any

derivative such as translation, transformation, or adaptation without permission from TP-LINK

reserved.

http://www.tp-link.com

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

 Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including interference that may cause

undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void

the user’s authority to operate the equipment.

Note: The manufacturer is not responsible for any radio or tv interference caused by unauthorized

modifications to this equipment. Such modifications could void the user’s authority to operate the

equipment.

FCC RF Radiation Exposure Statement:

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled

environment. This device and its antenna must not be co-located or operating in conjunction with any

other antenna or transmitter.

“To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile

Configurations. The antennas used for this transmitter must be installed to provide a separation distance

of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other

antenna or transmitter.”

CE Mark Warning

This is a class B product. In a domestic environment, this product may cause radio interference, in which

case the user may be required to take adequate measures.

Canadian Compliance Statement

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the

following two conditions:

(1) This device may not cause interference, and

(2)This device must accept any interference, including interference that may cause undesired operation

of the device.

Cet appareil est conforme aux norms CNR exemptes de licence d’Industrie Canada. Le fonctionnement

est soumis aux deux conditions suivantes:

(1) cet appareil ne doit pas provoquer d’interférences et

(2) cet appareil doit accepter toute interférence, y compris celles susceptibles de provoquer un

fonctionnement non souhaité de l’appareil.

Industry Canada Statement

Complies with the Canadian ICES-003 Class B specifications.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

This device complies with RSS 210 of Industry Canada. This Class B device meets all the requirements

of the Canadian interference-causing equipment regulations.

Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le matériel

brouilleur du Canada.

Korea Warning Statements

당해 무선설비는 운용중 전파혼신 가능성이 있음.

NCC Notice & BSMI Notice

注意！

依據低功率電波輻射性電機管理辦法

第十二條經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加

大功率或變更原設計之特性或功能。

第十四條低功率射頻電機之使用不得影響飛航安全及干擾合法通行；經發現有干擾現象時，應立即停用，

並改善至無干擾時方得繼續使用。前項合法通信，指依電信規定作業之無線電信。低功率射頻電機需忍受

合法通信或工業、科學以及醫療用電波輻射性電機設備之干擾。

減少電磁波影響，請妥適使用。

安全諮詢及注意事項

●請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。

●清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。

●注意防潮，請勿將水或其他液體潑灑到本產品上。　

●插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。

●請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。

●請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。

Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам

нормативних документів та вимогам, що передбачені чинними законодавчими актами України.

Safety Information

 When product has power button, the power button is one of the way to shut off the product; when

there is no power button, the only way to completely shut off power is to disconnect the product or

the power adapter from the power source.

 Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock and

voiding the limited warranty. If you need service, please contact us.

 Avoid water and wet locations.

This product can be used in the following countries:

AT BG BY CA CZ DE DK EE

ES FI FR GB GR HU IE IT

LT LV MT NL NO PL PT RO

RU SE SK TR UA US

TP-LINK TECHNOLOGIES CO., LTD

DECLARATION OF CONFORMITY

For the following equipment:

Product Description: 300Mbps AV500/AV200 WiFi Powerline Extender

Model No.: TL-WPA4220/TL-WPA2220

Trademark: TP-LINK

We declare under our own responsibility that the above products satisfy all the technical regulations

applicable to the product within the scope of Council Directives:

Directives 1999/5/EC, Directives 2004/108/EC, Directives 2006/95/EC, Directives 1999/519/EC,

Directives 2011/65/EU

The above product is in conformity with the following standards or other normative documents

EN 55022: 2010 + AC: 2011

EN 55024: 2010

EN 61000-3-2: 2006 + A1: 2009 + A2: 2009

EN 61000-3-3: 2013

EN 60950-1: 2006 + A11: 2009 + A1: 2010 + A12: 2011

EN 50412-2-1: 2005

EN 62311: 2008

EN 300 328 V1.8.1

EN 301 489-1 V1.9.2 & EN 301 489-17 V2.2.1

The product carries the CE Mark:

Person responsible for making this declaration:

Yang Hongliang

Product Manager of International Business

Date of issue: 2014

TP-LINK TECHNOLOGIES CO., LTD.

Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park, Shennan Rd,

Nanshan, Shenzhen, China

Important Safety Instructions

1. Do not open this product or attempt to service it; it may expose you to dangerous high voltage or

other risks.

2. Do not operate this product near water.

3. Do not place or operate this product near a radiator or a heat register.

4. Do not expose this product to dampness, dust or corrosive liquids.

5. Do not connect this product or disconnect it from a wall socket during a lightning or a thunderstorm.

6. Do not block the ventilation slots of this product, for insufficient airflow may harm it.

7. Do not put anything on this product.

8. Plug this product directly into a wall socket (100-240V~, 50/60Hz). Do not use an extension cord

between this product and the AC power source.

9. When plugging this product into a wall socket, make sure that the electrical socket is not damaged,

and that there is no gas leakage.

10. Place the connecting cables properly so that people won’t stumble or walk on it.

11. This product should be operated from the type of power indicated on the marking label. If you are not

sure of the type of power available, consult the qualified technician.

12. Unplug this product from the mains and refer the product to qualified service personnel for the

following conditions:

 If liquid has been spilled on the product

 If the product has been exposed to rain or water

13. Unplug this product from the wall socket before cleaning. Use a damp cloth for cleaning. Do not use

liquid cleaners or aerosol cleaners.

14. The specification of the fuse is T4AL250V for TL-WPA4220 (T2.5AL250V for TL-WPA2220). To

avoid damage, please do not change the fuse.

15. The Operating temperature is 0 ~4℃ 0 (32~10℃℉4)℉ . The Storage temperature is -40 ~70℃℃

(-40 ~158 )℉℉.

CONTENTS

Chapter 1 Introduction.......................................................................................................................... 1

1.1 System Requirement ..................................................................................................................... 1

1.2 Conventions...................................................................................................................................

1

Chapter 2 Hardware Connection.......................................................................................................... 3

2.1 Before You Begin........................................................................................................................... 3

2.2 LED Indicator................................................................................................................................. 4

2.3 Physical Interface .......................................................................................................................... 5

2.4 Hardware Connection .................................................................................................................... 5

2.5 Wi-Fi Clone Button for Super Range Extension............................................................................. 8

Chapter 3 Configuring the Device ..................................................................................................... 10

3.1 Login............................................................................................................................................ 10

3.1.1 For Wired Connection ........................................................................................................................ 10

3.1.2 For Wireless Connection ................................................................................................................... 12

3.2 Status...........................................................................................................................................

13

3.3 Network ....................................................................................................................................... 14

3.4 Wireless.......................................................................................................................................

15

3.4.1 Wireless Settings ................................................................................................................................

15

3.4.2 Wireless Security ................................................................................................................................

17

3.4.3 Wireless MAC Filtering ...................................................................................................................... 19

3.4.4 Wireless Advanced ............................................................................................................................. 21

3.4.5 Wireless Statistics............................................................................................................................... 22

3.5 Powerline.....................................................................................................................................

23

3.5.1 Network Settings................................................................................................................................. 23

3.5.2 Station Settings ...................................................................................................................................

23

3.6 System Tools ............................................................................................................................... 25

3.6.1 Firmware Upgrade.............................................................................................................................. 25

3.6.2 Factory Defaults..................................................................................................................................

27

3.6.3 Backup & Restore............................................................................................................................... 27

3.6.4 Reboot ..................................................................................................................................................

28

3.6.5 Password .............................................................................................................................................

28

3.6.6 System Log..........................................................................................................................................

29

Chapter 4 Connecting to Wireless Network...................................................................................... 30

4.1 In Windows 8 ............................................................................................................................... 30

4.2 In Windows 7 ............................................................................................................................... 31

4.3 In Windows Vista ......................................................................................................................... 33

4.4 In Windows XP ............................................................................................................................ 35

Chapter 5 Pair Button ......................................................................................................................... 37

5.1 Pair (Secure with 128 bits-AES) .................................................................................................. 37

5.2 Setting Up a Powerline Network with the Pair Button .................................................................. 37

5.3 Reset ........................................................................................................................................... 37

Appendix A: Troubleshooting Guide ................................................................................................. 39

TL-WPA4220/TL-WPA2220 300Mbps AV500/AV200 WiFi Powerline Extender

1

Chapter 1 Introduction

Congratulations on your purchase of this outstanding 300Mbps AV500/AV200 WiFi Powerline Extender.

This device is not only a 500Mbps/200Mbps powerline Ethernet adapter which transforms your house’s

existing electrical wiring into a ubiquitous networking infrastructure, but also a 300Mbps Wi-Fi Access

Point which creates a wireless network allowing for greater range and mobility.

As a powerline Ethernet adapter, it uses the existing power lines installed in a home as a path to

transmit digital data, voice, audio and video between devices. Simply plug this 300Mbps AV500/AV200

WiFi Powerline Extender into an ordinary AC power outlet, and then your Cable/xDSL broadband

connection or existing Ethernet (LAN) network can be easily extended to any other electrical outlet in

any room of a house with the absence of cabling. With powerline data rates of 500Mbps/200Mbps, full

multimedia application can easily be supported throughout the whole house.

As a Wi-Fi Access Point, it can transmit wireless data at the rate of up to 300Mbps. With multiple

protection measures including SSID broadcast control, wireless LAN WEP encryption, and Wi-Fi

Protected Access (WPA2- PSK, WPA-PSK), the device delivers complete data privacy.

It supports an easy, Web-based management utility. Even though you may not be familiar with the

device, you can easily configure it with the help of this Guide. The extender adds three new functions

which are found to be useful.

1. Connection with a new unassociated device via the Pair button.

2. Reset to default settings via the Reset button.

3. Wi-Fi Clone via Wi-Fi Clone button.

1.1 System Requirement

a) At least two power outlets (100-240V~, 50/60Hz) with standard home power wiring

b) A computer with the following:

 Operating System of Windows 2000/XP/2003/Vista/7/8

, Mac OS X, Linux

 Operating System with TCP/IP installed

 Pentium III compatible processor and above

 Ethernet LAN card installed with TCP/IP protocol

 64 MB RAM or more

 50 MB of free disk space (Minimum)

 CD-ROM Drive

1.2 Conventions

The extender, or TL-WPA4220/TL-WPA2220, or device mentioned in this User Guide stands for

TL-WPA4220/TL-WPA2220 300Mbps AV500/AV200 WiFi Powerline Extender without any explanations.

Parameters provided in the pictures are just references for setting up the product. They may differ from

the actual situation.

You can set the parameters according to your demand.



Note:

This User Guide is shared by TL-WPA4220 and TL-WPA2220. Here in this Guide we use TL-WPA4220

for example.

TL-WPA4220/TL-WPA2220 300Mbps AV500/AV200 WiFi Powerline Extender

2

The difference between them is:

 TL-WPA4220 300Mbps AV500 WiFi Powerline Extender with powerline data rate of up to

500Mbps;

 TL-WPA2220 300Mbps AV200 WiFi Powerline Extender with powerline data rate of up to

200Mbps.

TL-WPA4220/TL-WPA2220 300Mbps AV500/AV200 WiFi Powerline Extender

3

Chapter 2 Hardware Connection

2.1 Before You Begin

Please read this User Guide carefully before installing and using the equipment. The operating distance

or range of your wireless connection varies significantly based on the physical placement of the

powerline extender. Factors that can weaken signals by getting in the way of your network’s radio waves

are metal appliances or obstructions, and walls. Typical ranges vary based on the types of materials and

background RF (radio frequency) noise in your home or office.

For best performance of your wireless network, you are suggested to place your powerline extender:

1). Near the center of the area in which your wireless stations will operate.

2). In an elevated location such as a high shelf.

3). Away from the potential sources of interference, such as PCs, microwaves, and cordless phones.

4). Away from large metal surfaces.

Failure to follow these guidelines can result in significant performance degradation or inability to

wirelessly connect to the powerline extender.



Note:

Take notes that this 300Mbps AV500/AV200 WiFi Powerline Extender works in pairs or with another

powerline adapter. You need to plug the powerline extender into a power outlet; you will also need

another powerline extender or powerline adapter connected to your Cable/xDSL broadband (Ethernet

port) in order to extend your broadband connection or Internet surfing. With clean powerline, the

distance between two powerline devices can reach 300 meters, but the actual distance may vary due to

the environment.

Section below describes the 300Mbps AV500/AV200 WiFi Powerline Extender’s LED indicators,

physical interface and hardware connection mechanism.

TL-WPA4220/TL-WPA2220 300Mbps AV500/AV200 WiFi Powerline Extender

4

2.2 LED Indicator

The LED indicator displays information about the device’s status.

LEDs Name Status Indication

Solid The device is on.

Off The device is off.

Power LED

Blinking The device is in the pairing procedure.

Solid

The device is connected to a powerline network, but there

is no data being transferred.

Off The device isn’t connected to any powerline network.

Powerline

LED

Blinking The device is transferring data.

Solid The Ethernet port is connected.

Ethernet LED

Off

The Ethernet port isn’t connected.

Off The wireless function has been disabled.

Blinking slowly The extender is cloning Wi-Fi settings from other device.

Wi-Fi/Wi-Fi

Clone LED

Blinking quickly The wireless function has been enabled.

TL-WPA4220/TL-WPA2220 300Mbps AV500/AV200 WiFi Powerline Extender

5

2.3 Physical Interface

There are four physical items on this device.

Wi-Fi/Wi-Fi Clone Button

Power Plug

Ethernet Port

Reset Button

Pair Button

Item Description

Wi-Fi/Wi-Fi

Clone Button

Press the button for 2 seconds to start Wi-Fi Clone.

Press the button for 5 seconds to enable or disable the wireless function.

Ethernet Port Two 10/100Mbps Ethernet port connected to PC LAN card or broadband device.

Reset Button

Press the button more than 5 seconds, the device will restore to its factory

defaults.

Pair Button Pair button is used to secure a powerline network.

Power Plug* A Power Plug connected to any (100V–240V~, 50/60Hz) power socket.

* The provided power plug may differ from the picture due to different regional power specifications.

Here we take the EU version as an example.



Note:

1. If you press the Pair button for more than 10 seconds, the extender will leave the network it is

associated with and its network name assumes a random value.

2. For detail information about the Reset button and Pair button, please refer to Chapter 5 Pair Button

.

2.4 Hardware Connection

Please first make sure that your PC can successfully access the Internet via the router. Then connect

the powerline devices by following the instructions below.

Step 1: Connecting to the Internet

This section describes how to connect the powerline extender into your existing network. Follow the

procedures described below:

TL-WPA4220/TL-WPA2220 300Mbps AV500/AV200 WiFi Powerline Extender

6

1． Connect one end of an Ethernet (RJ45) cable to the Ethernet port of the powerline extender or a

compatible powerline adapter like TL-PA4010.

2． Connect the other end of the Ethernet (RJ45) cable to an available Ethernet port of your wireless

router.

3． Plug the powerline extender or powerline adapter into a wall socket.

4． Check and confirm the LEDs status. (The Power LED and Ethernet LED on the powerline device

should be ON.)

The hardware connection mechanism is shown below:

 Note:

Do not connect the powerline extender or powerline adapter to an extension lead, power strip, extension

cord, or surge protector, as these may degrade the network performance.

Step 2: Connecting the Computer

Following are the steps to properly connect the powerline extender to your computer:

1． Connect one end of the provided Ethernet (RJ45) cable to the powerline extender’s Ethernet port.

2． Connect the other end of the Ethernet (RJ45) cable to you computer’s LAN port.

3． Plug the powerline extender into a wall socket next to the computer.

4． Turn on your computer.

5． Check and confirm that the Power LED and Ethernet LED on the powerline extender are ON.

TL-WPA4220/TL-WPA2220 300Mbps AV500/AV200 WiFi Powerline Extender

7

The hardware connection mechanism is shown below:

As soon as the powerline devices are connected following the steps above, a powerline network is

available.

TL-WPA4220/TL-WPA2220 300Mbps AV500/AV200 WiFi Powerline Extender

8

2.5 Wi-Fi Clone Button for Super Range Extension

Wi-Fi Clone button is used for copying the wireless settings (including SSID and wireless password)

from the front wireless router.

Wi-Fi Clone Steps:

Before taking the steps below, we strongly recommend you make sure the current wireless password of

the front router isn’t the default value.

1. Press the WPS button on the router for 2 seconds. (Here we take TP-LINK router as an example.)

2. Press the Wi-Fi Clone button on the extender for 2 seconds. The extender will reboot later.

* It’s recommended that you plug the extender near the router to use Wi-Fi Clone button.

After Wi-Fi Clone:

A unified wireless network is established. The SSID and wireless password of the powerline extender

will be the same as the wireless router.

TL-WPA4220/TL-WPA2220 300Mbps AV500/AV200 WiFi Powerline Extender

9



Note:

If you want to establish a secure and separate wireless network from the wireless router, please refer to

3.4.2 Wireless Security

to set a different SSID and password for your powerline extender.

TL-WPA4220/TL-WPA2220 300Mbps AV500/AV200 WiFi Powerline Extender

10

Chapter 3 Configuring the Device

This Chapter describes how to configure your Access Point via the web-based management page. The

300Mbps AV500/AV200 WiFi Powerline Extender is easy to configure and manage with the Web-based

(Internet Explorer, Netscape

®

Navigator, Firefox, Safari, Opera or Chrome) management page, which

can be launched on any windows, Macintosh or UNIX OS with a web browser.

3.1 Login

3.1.1 For Wired Connection

If your computer is connected to the extender via Ethernet cable, you can log in to the extender by

following the steps below:

1. Insert the TP-LINK Resource CD into the CD-ROM drive. The following screen will appear. Select

model TL-WPA4220 and then choose Management Utility from the drop-down menu.

Figure 3-1 Setup Wizard

TL-WPA4220/TL-WPA2220 300Mbps AV500/AV200 WiFi Powerline Extender

11

2. Find the model to be configured and click Connect to log in to the Web-based management utility.

Figure 3-2 Management Utility

 Note:

If another TL-WPA4220 is displayed on the screen above and you cannot decide which model is the

one you are configuring, please refer to the MAC address under MAC Address column. The device’s

MAC address can be found on the label at the bottom of the device.

3. Enter admin for the User name and Password (both in lower case letters) in the screen below. Then

click OK or press Enter.

Figure 3-3 Login Window

TL-WPA4220/TL-WPA2220 300Mbps AV500/AV200 WiFi Powerline Extender

12



Note:

If the above screen does not prompt, it means that your web-browser has been set to a proxy. Go to

Tools >Internet Options>Connections>LAN Settings, in the screen that appears, cancel the

Using Proxy checkbox, and click OK to finish it.

3.1.2 For Wireless Connection

If your device is

connected to the extender via wireless, you can log in to the extender by following the

steps below:

1. Launch a web-browser and type in the default domain name http://tplinkplclogin.net

in the address

field.

Figure 3-4 Log in to the Router

2. Enter admin for the User name and Password (both in lower case letters) in the screen below. Then

click OK or press Enter.

Figure 3-5 Login Windows



Note:

If the above screen does not prompt, it means that your web-browser has been set to a proxy. Go to

Tools>Internet Options>Connections>LAN Settings, in the screen that appears, cancel the

Using Proxy checkbox, and click OK to finish it.

After a successful login, you can configure and manage the device. There are six main menus on the

leftmost column of the Web-based management page: Status, Network, Wireless, Powerline and

System Tools. Submenus will be available after clicking one of the main menus. On the right of the

Web-based management page lays the detailed explanations and instructions for the corresponding

page.

Page is loading ...

TP-LINK AV200 User manual

TP-LINK AV200 User manual

Related papers

Other documents