Cisco WUSB54GC User guide

USER GUIDE

Wireless-N USB Network Adapter

with Dual-Band

Model: WUSB600N

About This Guide

i

Wireless-N USB Network Adapter with Dual-Band

About This Guide

Icon Descriptions

While reading through the User Guide you may see

various icons that call attention to specific items. Below is

a description of these icons:

NOTE: This check mark indicates that there is

a note of interest and is something that you

should pay special attention to while using the

product.

WARNING: This exclamation point indicates

that there is a caution or warning and it is

something that could damage your property or

product.

WEB: This globe icon indicates a noteworthy

website address or e-mail address.

Online Resources

Website addresses in this document are listed without

http:// in front of the address because most current web

browsers do not require it. If you use an older web browser,

you may have to add http:// in front of the web address.

Resource Website

Linksys www.linksysbycicso.com

Linksys International www.linksysbycisco.com/international

Glossary www.linksysbycisco.com/glossary

Network Security www.linksysbycisco.com/security

Copyright and Trademarks

Linksys, Cisco, and the Cisco Logo are

registered trademarks or trademarks

of Cisco Systems, Inc. and/or its

affiliates in the U.S. and certain other

countries. Other brands and product

names are trademarks or registered

trademarks of their respective

Table of Contents

ii

Wireless-N USB Network Adapter with Dual-Band

Chapter 1: Product Overview 1

Storing the Cap. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

USB Extension Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Chapter 2: Wireless Security Checklist 2

General Network Security Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Additional Security Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Chapter 3: Conguration 3

How to Access the Wireless Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

How to Use the Wireless Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Saved Networks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Appendix A: Troubleshooting 9

Appendix B: Windows Vista Conguration 10

Windows Vista Conguration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

New Wireless Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Appendix C: Windows XP Wireless Zero Conguration 13

Windows XP Wireless Zero Conguration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Appendix D: Specications 15

Appendix E: Warranty Information 16

Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Appendix F: Regulatory Information 18

FCC Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

FCC Radiation Exposure Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Safety Notices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Industry Canada Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Restrictions in the 5 GHz Band . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Avis d’Industrie Canada. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Restrictions dans la bande 5 GHz. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Wireless Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Avis de non-responsabilité concernant les appareils sans l . . . . . . . . . . . . . . . . . .19

User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste

Electric and Electronic Equipment (WEEE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Appendix G: Software End User License Agreement 24

Cisco Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Software Licenses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Chapter 1

Product Overview

1

Wireless-N USB Network Adapter with Dual-Band

Chapter 1:

Product Overview

Thank you for choosing the Linksys by Cisco Wireless-N

USB Network Adapter with Dual-Band. Using the latest

wireless networking technology, the Adapter adds

or upgrades wireless connectivity on your notebook

computer. To help protect your data and privacy, you can

use industrial-strength WPA2 encryption to protect your

wireless connection.

LED

Link (Blue) The LED flashes when there is

wireless network activity.

Storing the Cap

When the Adapter is plugged into the USB Extension Base

or your computer’s USB port, the cap may be stored on

the top of the Adapter.

To store the cap, push it onto the top of the adapter until

it fits snugly.

USB Extension Base

A USB Extension Base is provided for easy access to the

USB port. To use the USB Extension Base, connect the

Adapter to the Base, then connect the USB Extension Base

to the USB port on your PC or laptop.

Chapter 2

Wireless Security Checklist

2

Wireless-N USB Network Adapter with Dual-Band

Chapter 2:

Wireless Security Checklist

Wireless networks are convenient and easy to install, so

homes with high-speed Internet access are adopting them

at a rapid pace. Because wireless networking operates by

sending information over radio waves, it can be more

vulnerable to intruders than a traditional wired network.

Like signals from your cellular or cordless phones, signals

from your wireless network can also be intercepted. Since

you cannot physically prevent someone from connecting

to your wireless network, you need to take some additional

steps to keep your network secure.

1. Change the default wireless

network name or SSID

Wireless devices have a default wireless network name

or Service Set Identifier (SSID) set by the factory. This

is the name of your wireless network, and can be up

to 32 characters in length. Linksys wireless products

use linksys as the default wireless network name. You

should change the wireless network name to something

unique to distinguish your wireless network from other

wireless networks that may exist around you, but do not

use personal information (such as your Social Security

number) because this information may be available for

anyone to see when browsing for wireless networks.

2. Change the default password

For wireless products such as access points and routers,

you will be asked for a password when you want to change

their settings. These devices have a default password set

by the factory. The Linksys default password is admin.

Hackers know these defaults and may try to use them

to access your wireless device and change your network

settings. To thwart any unauthorized changes, customize

the device’s password so it will be hard to guess.

3. Enable MAC address filtering

Linksys routers give you the ability to enable Media Access

Control (MAC) address filtering. The MAC address is a

unique series of numbers and letters assigned to every

networking device. With MAC address filtering enabled,

wireless network access is provided solely for wireless

devices with specific MAC addresses. For example, you can

specify the MAC address of each computer in your home

so that only those computers can access your wireless

network.

4. Enable encryption

Encryption protects data transmitted over a wireless

network. Wi-Fi Protected Access (WPA/WPA2) and Wired

Equivalent Privacy (WEP) offer different levels of security

for wireless communication.

A network encrypted with WPA/WPA2 is more secure

than a network encrypted with WEP, because WPA/WPA2

uses dynamic key encryption. To protect the information

as it passes over the airwaves, you should enable the

highest level of encryption supported by your network

equipment.

WEP is an older encryption standard and may be the

only option available on some older devices that do not

support WPA.

General Network Security Guidelines

Wireless network security is useless if the underlying

network is not secure.

• Password protect all computers on the network and

individually password protect sensitive files.

• Change passwords on a regular basis.

• Install anti-virus software and personal firewall

software.

• Disable file sharing (peer-to-peer). Some applications

may open file sharing without your consent and/or

knowledge.

Additional Security Tips

• Keep wireless routers, access points, or gateways away

from exterior walls and windows.

• Turn wireless routers, access points, or gateways

off when they are not being used (at night, during

vacations).

• Use strong passphrases that are at least eight characters

in length. Combine letters and numbers to avoid using

standard words that can be found in the dictionary.

WEB: For more information on wireless security,

visit www.linksysbycisco.com/security

Chapter 3

Advanced Configuration

3

Wireless-N USB Network Adapter with Dual-Band

Chapter 3:

Configuration

The Linksys Wireless Manager is used to configure the

Adapter. The Wireless Manager lets you search for available

wireless networks, establish or terminate a connection

with a wireless network, and save a wireless network’s

settings.

How to Access the Wireless Manager

After you have installed the Adapter, the Linksys Wireless

Manager icon appears in the system tray of your computer.

If the Adapter is connected to a wireless network, the icon

will have green bars (the exact number of green bars

varies depending on the network’s signal strength). If the

Adapter is not connected to a wireless network, the icon

will have gray bars with a red X.

Linksys Wireless Manager Icon—

Connected to a Wireless Network

Linksys Wireless Manager Icon—

Not Connected to a Wireless Network

To open the Wireless Manager, click the icon, and then

select View Wireless Networks... from the pop-up menu.

(To skip the pop-up menu, double-click the icon instead.)

To close the Wireless Manager, click the icon, and then

select Close from the pop-up menu.

Wireless Manager Icon Pop-up Menu

How to Use the Wireless Manager

The Wireless Manager opens with the Connect to a

Wireless Network screen. This screen allows you to connect

to a wireless network, or to disconnect from a wireless

network.

When the Connect to a Wireless Network screen first

appears, it displays a message indicating that the Wireless

Manager is searching for wireless networks within range.

When the search is complete, the screen displays the

available wireless networks within range.

Connect to a Wireless Network—Searching for Wireless Networks

Connect to a Wireless Network—Available Wireless Networks

The list of available wireless networks provides the

following information about each network:

• Network name The network’s unique name or SSID.

• Connection status The word Connected appears if

the Adapter is connected to the network.

• Wi-Fi Protected Setup support The icon

appears

if

the network supports Wi-Fi Protected Setup.

NOTE: The Adapter supports Wi-Fi Protected

Setup, a feature that makes it easy to set up

a wireless network. For information on this

feature, go to How to Connect Using Wi-Fi

Protected Setup, page 6.

• Security The icon appears if the network uses

wireless security. The security type (WPA2, WPA, WEP) is

listed below the network name.

• Network signal strength The green bars in the

icon indicate the network’s signal strength; is the

strongest level and is the weakest level.

Chapter 3

Advanced Configuration

4

Wireless-N USB Network Adapter with Dual-Band

To connect to a wireless network, go to How to Connect to

a Wireless Network, page 4. To disconnect from a wireless

network, select the network, and click Disconnect. To

refresh the list of available networks, click Search Again.

How to Connect to a Wireless Network

Follow these instructions to connect to a wireless network

that has not been saved. (To connect to a saved network,

go to How to Connect to a Saved Network, page 8.)

1. On the Connect to a Wireless Network screen, locate

the name of your wireless network in the list. If your

wireless network is not in the list, go to How to

Connect to a Hidden Wireless Network, page 5.

2. If your wireless network supports Wi-Fi Protected

Setup (the icon appears next to the network’s

name), go to How to Connect Using Wi-Fi Protected

Setup, page 6.

3. Select your network, and then click Connect.

Select a Wireless Network

4. If the wireless network uses wireless security, enter the

security key. Click Next.

Enter Wireless Network’s Security Key

5. The Checking Connection screen appears while the

Wireless Manager establishes the wireless connection.

When it is finished, click Next.

Checking Connection

6. The Connected to Your Network screen appears. To

save your network’s settings, select Remember this

network. (Saving a network’s settings will make it

easier to reconnect

to the network.)

Click Finish to exit

the Wireless Manager.

Connected to Your Network

Congratulations! The Adapter is connected to

the network.

Chapter 3

Advanced Configuration

5

Wireless-N USB Network Adapter with Dual-Band

How to Connect to a Hidden Wireless Network

NOTE: By default, a wireless network’s router

broadcasts the network name (SSID).

A “hidden”

wireless network is a network whose router has

been configured not to broadcast the network

name (SSID).

Follow these instructions to connect to a wireless network

that is not listed on the Connect to a Wireless Network

screen.

1. On the Connect to a Wireless Network screen, select My

network is not in this list. Click Next.

Select My Network is Not in This List

2. The next screen asks if you want to connect to a hidden

network. If your network is hidden, select Connect to

hidden network. Click Next.

Confirm Connection to Hidden Network

NOTE: If your wireless network is NOT hidden,

select My network is not hidden, and then

click Next. Follow the instructions on the next

screen—verify that your network router is

powered on and is within range of the Adapter,

and then click Retry to search for wireless

networks again. Then go to How to Connect to

a Wireless Network, page 4 to continue.

3. Enter your wireless network’s name (SSID). Click Next.

Enter Wireless Network’s Name (SSID)

4. If your wireless network uses wireless security,

enter the security key. Click Next.

If your wireless network does not use wireless security,

leave the security key field blank, and click Next.

Enter Wireless Network’s Security Key

Chapter 3

Advanced Configuration

6

Wireless-N USB Network Adapter with Dual-Band

5. The Checking Connection screen appears.

Checking Connection

6. The Connected to Your Network screen appears. To

save your network’s settings, select Remember this

network. (Saving a network’s settings will make it

easier to reconnect

to the network.)

Click Finish to exit

the Wireless Manager.

Connected to Your Network

Congratulations! The Adapter is connected to

the network.

How to Connect Using Wi-Fi Protected Setup

On the Connect to a Wireless Network screen, the Wi-Fi

Protected Setup icon ( ) indicates a network that supports

Wi-Fi Protected Setup. Follow these instructions to connect

to a wireless network using Wi-Fi Protected Setup.

NOTE: Before you begin, make sure the router

and the computer with the Adapter are in the

same room

.

1. On the Connect to a Wireless Network screen, select

your network, and then click Connect.

Select the Wireless Network

2. The Quickly Connect Using Push Button screen appears.

Quick Connect Using Push Button

3. Press the router’s Wi-Fi Protected Setup button

until an LED lights up. If your router does not have this

button, click Skip and go to Enter the Adapter’s PIN

Number, page 7.

4. Within two minutes, click Connect on the Quickly

Connect Using Push Button screen.

Chapter 3

Advanced Configuration

7

Wireless-N USB Network Adapter with Dual-Band

5. The Adapter connects to the network.

Connecting to the Network via Wi-Fi Protected Setup

NOTE: If the connection cannot be set up, the

message, “Registration failed” appears. If this

happens, use one of two options:

• Push Button Press the router’s Wi-Fi

Protected Setup button until an LED

lights up. Then click Connect to try again.

• PIN Click Skip, and then go to Enter the

Adapter’s PIN Number, page 7.

6. The Connected to Your Network screen appears. To

save your network’s settings, select Remember this

network. (Saving a network’s settings will make it

easier to reconnect

to the network.)

Click Finish to

exit the Wireless Manager.

Connected to Your Network

Congratulations! The Adapter is connected to

the network.

Enter the Adapter’s PIN Number

Enter the PIN Number

1. Access the web-based utility of the router. (Refer to the

router’s documentation for instructions.)

2. On the router’s Wi-Fi Protected Setup screen, enter

the Adapter’s PIN number in the appropriate field.

Then perform the appropriate action to save the PIN

number; for example, click Register. (Refer to the

router’s documentation for instructions.)

NOTE: Enter the Adapter’s PIN number without

the hyphen.

3. The Adapter connects to the network, and the

Connected to Your Network screen appears. To save

your network’s settings, select Remember this

network. (Saving a network’s settings will make it

easier to reconnect

to the network.)

Click Finish to exit

the Wireless Manager.

Connected to Your Network

Congratulations! The Adapter is connected to

the network.

Chapter 3

Advanced Configuration

8

Wireless-N USB Network Adapter with Dual-Band

Saved Networks

When you connect to a wireless network, you can save its

settings so that it will be easier to reconnect to the network

at a later time. This is most helpful with hidden networks;

if you do not save a hidden network’s settings, you will

have to enter the network name (SSID) and security key.

To save a network, select Remember this network on

the Connected to Your Network screen (the last screen that

appears when you connect to a network).

Remember this Network

To see a list of your saved networks, select Saved

networks from the View drop-down menu of the Connect

to a Wireless Network screen.

Saved Networks

To delete a saved network from the list, select the network

and click Remove. To change a network’s position in

the list, select the network, and click Move up or Move

down.

How to Connect to a Saved Network

To connect to a saved network, follow these instructions.

1. In the Connect to a Wireless Network screen, select

Saved networks from the View drop-down menu.

2. The screen displays a list of your saved networks.

Saved Networks

3. Select the network you want, and then click Connect.

4. The Adapter connects to the network and the

Connected to Your Network screen appears. Click Finish

to exit the Wireless Manager.

Connected to Your Network

Congratulations! The Adapter is connected to

the network.

Appendix A

Troubleshooting

9

Wireless-N USB Network Adapter with Dual-Band

Appendix A:

Troubleshooting

Your computer does not recognize the Adapter.

Make sure that the Adapter is properly inserted into the

USB slot.

The Adapter does not work properly.

Remove the Adapter, and then reinsert it into the

computer’s USB slot.

Your computer cannot communicate with the other

computers linked via Ethernet in the Infrastructure

conguration.

1. Make sure that the computers are powered on.

2. Make sure that the Adapter is configured with the

same Wireless Network Name (SSID) and wireless

security settings as the other wireless computers in

the Infrastructure configuration.

WEB: If your questions are not addressed

here, refer to the Linksys website,

www.linksysbycisco.com

Appendix B

Windows Vista Configuration

10

Wireless-N USB Network Adapter with Dual-Band

Appendix B:

Windows Vista

Configuration

Windows Vista Configuration

After you have installed the Adapter, the Windows Vista

Wireless Network Configuration utility icon appears on

your computer’s system tray.

Wireless Network Configuration Utility Icon

When your mouse pointer hovers over the icon, the status

information of your wireless connection appears.

Wireless Connection Status

New Wireless Connection

To connect to a different wireless network:

1. Right-click the Wireless Network Configuration

utility icon.

2. Click Connect to a network.

Utility Menu

3. Select your network, and then click Connect.

Select Network

4. If your network has wireless security, go to step 5.

If your network has no wireless security, this screen

appears. To connect to your unsecured network, click

Connect Anyway and go to step 7.

Unsecured Network

Appendix B

Windows Vista Configuration

11

Wireless-N USB Network Adapter with Dual-Band

5. Enter the security key, WEP key, or passphrase (also

known as a pre-shared key), depending on your type

of security. Click Connect.

Secured Network

6. This screen appears while the Adapter connects to

your network. Do not cancel, unless you want to end

the installation.

Connecting to Network

7. This screen appears when you are connected to your

network. Select Save this network, if you want to save

your settings. Click Close.

Connected to Network

8. The Set Network Location screen may appear to help

apply the correct settings for your type of location.

Select Home, Work, or Public location.

Select Network Location

Appendix B

Windows Vista Configuration

12

Wireless-N USB Network Adapter with Dual-Band

9. This screen varies according to the selected location.

Click Close.

Network Settings Saved

NOTE: For help with the Windows Vista Wireless

Network Conguration utility, refer to Windows

Vista Help and Support, by clicking Vista’s Start

button

> Help and Support.

Your computer is now connected to your

wireless network.

Appendix C

Windows XP Wireless Zero Configuration

13

Wireless-N USB Network Adapter with Dual-Band

Appendix C:

Windows XP Wireless Zero

Configuration

Windows XP Wireless Zero Configuration

Windows XP has a built-in wireless configuration utility.

If you prefer to use the Windows XP Wireless Zero

Configuration Utility to control your adapter, you must

first uninstall the Linksys Wireless Manager.

NOTE: If your network is using WPA2 encryption,

make sure that you have installed the Update

for Windows XP (KB893357), available at

www.microsoft.com.

1. To uninstall the Linksys Wireless Manager, go to

Start > Control Panel.

Start Menu

2. The Control Panel window opens. Click the Add or

Remove Programs icon.

3. Select Linksys Wireless Manager from the list of

programs in the Add or Remove Programs window.

Add or Remove Programs

4. The Uninstall screen opens. Click Yes to uninstall the

Linksys Wireless Manager.

Uninstall Screen

5. When the uninstall is complete, you will be asked if

you want to restart your computer. Select Yes.

Restart Your Computer Screen

NOTE: For more information on the Windows

XP Wireless Zero Configuration utility, refer to

Windows Help.

6. After your computer restarts, the Windows XP Wireless

Zero Configuration icon appears in your computer’s

system tray. Double-click the icon.

Windows XP Wireless Zero Configuration Icon

Appendix C

Windows XP Wireless Zero Configuration

14

Wireless-N USB Network Adapter with Dual-Band

7. A window will open displaying the available wireless

networks. Select the network that you want and click

Connect.

If your network does not have wireless security

enabled, go to step 8.

If your network does have wireless security enabled,

go to step 9.

Available Wireless Network

8. If your network does not have wireless security enabled,

click Connect Anyway to connect the Adapter to your

network.

No Wireless Security

9. If your network uses WEP wireless security, enter the

WEP Key in the Network Key and Confirm network key

fields. If your network uses WPA Personal wireless

security, enter the Passphrase in the Network Key and

Confirm network key fields. Click Connect.

Wireless Security

NOTE: Windows XP Wireless Zero Configuration

does not support the use of a WEP passphrase.

Enter the exact WEP key used by your wireless

router or access point.

10. Your wireless network will appear as Connected when

your connection is active.

Wireless Network Connection

For more information about wireless networking on a

Windows XP computer, click Start > Help > Support.

Enter the keyword wireless in the field provided, and

press the Enter key.

Your computer is now connected to your

wireless network.

Appendix D

Specifications

15

Wireless-N USB Network Adapter with Dual-Band

Appendix D:

Specifications

Model WUSB600N

Standards 802.11a, 802.11b,

802.11g, Draft 802.11n

LEDs Link/Act

Number of Antennas 2 Internal Antennas

Transmitted Power

2.4 GHz @ 11 Mbps data rate:

18 dBm ± 1.5 dBm

2.4 GHz @ 54 Mbps data rate:

14 dBm ± 1.5 dBm

5 GHz @ 54Mbps data rate:

12 dBm ± 1.5 dBm

2.4 GHz, 11N (MCS0, HT20/40):

18 dBm ± 1.5 dBm

2.4 GHz, 11N (MCS8, HT20/40):

18 dBm ± 1.5 dBm

2.4 GHz, 11N (MCS15, HT20/40):

12 dBm ± 1.5 dBm

5 GHz, 11N (MCS0, HT20/40):

16 dBm ± 1.5 dBm

5 GHz, 11N (MCS8, HT20/40):

16 dBm ± 1.5 dBm

5 GHz, 11N (MCS15, HT20/40):

10 dBm ± 1.5 dBm

Receive Sensitivity

-84 dBm @11 Mbps

-70 dBm @54 Mbps

-83 dBm @2.4 GHz/5GHz, MCS0, HT20

-80 dBm @2.4 GHz/5GHz, MCS0, HT40

-83 dBm @2.4 GHz/5GHz, MCS8, HT20

-80 dBm @2.4 GHz/5GHz, MCS8, HT40

-65 dBm @2.4 GHz/5GHz, MCS15, HT20

-62 dBm @2.4 GHz/5GHz, MCS15, HT40

Antenna Gain in dBi 802.11a: 5 GHz => 4 dBi

802.11g: 2.4 GHz =>

TX0: 0.5 dBi, TX1: 1.4 dBi

Power Consumption

TX (2.4G): 330 mA, HT20; 340 mA HT40 at 5V

TX (5G): 400 mA, HT20; 430 mA HT40 at 5V

RX (2.4G): 140 mA, HT20; 160 mA HT40 at 5V

RX (5G): 150 mA, HT20; 180 mA HT40 at 5V

Standby: 150 mA

Radio O: 20 mA

Security Features WEP, WPA & WPA2 Personal,

WPA & WPA2 Enterprise

Security Key Bits Up to 128-Bit Encryption

OS Requirements Up-to-date Windows XP,

Vista or Vista 64-bit Edition

Environmental

Dimensions 3.15" x 1.00" x 0.49"

(79.9 x 25.4 x 12.4 mm)

Weight 0.39 oz (11 g)

Certication FCC, CE, IC, UL, RoHS, WEEE, IDA,

C-Tick, Wi-Fi A/B/G/Draft-N

Operating Temp. 32 to 104ºF (0 to 40ºC)

Storage Temp. -4 to 158ºF (–20 to 70ºC)

Operating Humidity 10 to 85% Noncondensing

Storage Humidity 5 to 90% Noncondensing

Specications are subject to change without notice.

Appendix E

Warranty Information

16

Wireless-N USB Network Adapter with Dual-Band

Appendix E:

Warranty Information

Limited Warranty

Linksys warrants this Linksys hardware product against

defects in materials and workmanship under normal

use for the Warranty Period, which begins on the date of

purchase by the original end-user purchaser and lasts for

the period specified below:

• One (1) year for new product

• Ninety (90) days for refurbished product

Your exclusive remedy and Linksys’ entire liability under

this limited warranty will be for Linksys, at its option, to

(a) repair the product with new or refurbished parts,

(b) replace the product with a reasonably available

equivalent new or refurbished Linksys product, or (c)refund

the purchase price of the product less any rebates. Any

repaired or replacement products will be warranted for

the remainder of the original Warranty Period or thirty (30)

days, whichever is longer. All products and parts that are

replaced become the property of Linksys.

Linksys additionally warrants that any media on which

the software may be provided will be free from defects in

materials and workmanship under normal use for a period

of ninety (90) days from the date of original purchase.

Your exclusive remedy and Linksys’ entire liability under

this limited warranty will be for Linksys, at its option, to

(a)replace the software media, or (b)refund the purchase

price of the software media.

Exclusions and Limitations

This limited warranty does not apply if: (a)the product

assembly seal has been removed or damaged, (b) the

product has been altered or modified, except by Linksys,

(c) the product damage was caused by use with non-

Linksys products, (d)the product has not been installed,

operated, repaired, or maintained in accordance with

instructions supplied by Linksys, (e) the product has

been subjected to abnormal physical or electrical stress,

misuse, negligence, or accident, (f)the serial number on

the Product has been altered, defaced, or removed, or

(g)the product is supplied or licensed for beta, evaluation,

testing or demonstration purposes for which Linksys does

not charge a purchase price or license fee.

EXCEPT FOR THE LIMITED WARRANTY ON MEDIA SET FORTH

ABOVE AND TO THE MAXIMUM EXTENT PERMITTED BY

APPLICABLE LAW, ALL SOFTWARE PROVIDED BY LINKSYS

WITH THE PRODUCT, WHETHER FACTORY LOADED ON THE

PRODUCT OR CONTAINED ON MEDIA ACCOMPANYING

THE PRODUCT, IS PROVIDED “AS IS” WITHOUT WARRANTY

OF ANY KIND. Without limiting the foregoing, Linksys does

not warrant that the operation of the product or software

will be uninterrupted or error free. Also, due to the

continual development of new techniques for intruding

upon and attacking networks, Linksys does not warrant

that the product, software or any equipment, system or

network on which the product or software is used will be

free of vulnerability to intrusion or attack. The product

may include or be bundled with third party software or

service offerings. This limited warranty shall not apply to

such third party software or service offerings. This limited

warranty does not guarantee any continued availability

of a third party’s service for which this product’s use or

operation may require.

TO THE EXTENT NOT PROHIBITED BY APPLICABLE

LAW, ALL IMPLIED WARRANTIES AND CONDITIONS

OF MERCHANTABILITY, SATISFACTORY QUALITY OR

FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO

THE DURATION OF THE WARRANTY PERIOD. ALL OTHER

EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS

AND WARRANTIES ARE DISCLAIMED. Some jurisdictions

do not allow limitations on how long an implied warranty

lasts, so the above limitation may not apply to you. This

limited warranty gives you specific legal rights, and you

may also have other rights which vary by jurisdiction.

TO THE EXTENT NOT PROHIBITED BY APPLICABLE LAW,

IN NO EVENT WILL LINKSYS BE LIABLE FOR ANY LOST

DATA, REVENUE OR PROFIT, OR FOR SPECIAL, INDIRECT,

CONSEQUENTIAL, INCIDENTAL OR PUNITIVE DAMAGES,

REGARDLESS OF THE THEORY OF LIABILITY (INCLUDING

NEGLIGENCE), ARISING OUT OF OR RELATED TO THE USE

OF OR INABILITY TO USE THE PRODUCT, SOFTWARE OR

ANY SERVICES PROVIDED IN RESPECT OF SUCH PRODUCT

OR SOFTWARE, EVEN IF LINKSYS HAS BEEN ADVISED OF

THE POSSIBILITY OF SUCH DAMAGES. TO THE EXTENT

NOT PROHIBITED BY APPLICABLE LAW, IN NO EVENT WILL

LINKSYS’ LIABILITY EXCEED THE AMOUNT PAID BY YOU

FOR THE PRODUCT. The foregoing limitations will apply

even if any warranty or remedy provided under this limited

warranty fails of its essential purpose. Some jurisdictions

do not allow the exclusion or limitation of incidental

or consequential damages, so the above limitation or

exclusion may not apply to you.

Obtaining Warranty Service

If you have a question about your product

or experience a problem with it, please go to

www.linksysbycisco.com/support where you will find a

variety of online support tools and information to assist

you with your product. If the product proves defective

during the Warranty Period, contact Linksys Technical

Support for instructions on how to obtain warranty service.

The telephone number for Linksys Technical Support in

your area can be found in the product User Guide and

at www.linksysbycisco.com. Have your product serial

number and proof of purchase on hand when calling. A

Appendix E

Warranty Information

17

Wireless-N USB Network Adapter with Dual-Band

DATED PROOF OF ORIGINAL PURCHASE IS REQUIRED TO

PROCESS WARRANTY CLAIMS. If you are requested to

return your product, you will be given a Return Materials

Authorization (RMA) number. You are responsible for

properly packaging and shipping your product to Linksys

at your cost and risk. You must include the RMA number

and a copy of your dated proof of original purchase when

returning your product. Products received without a RMA

number and dated proof of original purchase will be

rejected. Do not include any other items with the product

you are returning to Linksys. Defective product covered

by this limited warranty will be repaired or replaced and

returned to you without charge. Customers outside of

the United States of America and Canada are responsible

for all shipping and handling charges, custom duties,

VAT and other associated taxes and charges. Repairs or

replacements not covered under this limited warranty will

be subject to charge at Linksys’ then-current rates.

Technical Support

This limited warranty is neither a service nor a

support contract. Information about Linksys’ current

technical support offerings and policies (including

any fees for support services) can be found at

www.linksysbycisco.com/support.

This limited warranty is governed by the laws of the

jurisdiction in which the Product was purchased by you.

Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine,

CA 92623.

Page is loading ...

Cisco WUSB54GC User guide

This manual is also suitable for

Cisco WUSB54GC User guide

Related papers

Other documents