DataComm 45-0009-LA User manual

45-0009-LA
DataComm
Brand
DataComm
Model
45-0009-LA
Category
Electrical wallplates
Type
User manual

This manual is also suitable for

4-1/16”
Parts Included
1. One (1) Easy Mount Recessed Low Voltage Cable Plate
Tools Needed
1. Drywall saw
2. 6 Ft. tape measure
3. Pencil
4. Screwdriver
Use DataComm Electronics’ Easy Mount Recessed Low Voltage
Cable Plates to install low voltage cables behind your flat panel
TV, (see Figures 2 & 3), your amplifier or other audio and video
devices. These recessed low voltage cable plates are designed
for use with Low Voltage / Data Cables “ONLY”.
Easy Mount Recessed Low Voltage Cable Plates are designed
with the low voltage mounting brackets molded to the back of the
plate (see Figure 1). The wall plate can be installed upright or
upside down (see Figures 2 & 3 for upright installation).
Determine the location of your flat panel TV, amplifier or
audio/video device. Use the enclosed template to cut a hole in
the drywall. When cutting the hole in the drywall, allow for the
location of the stud. Now simply pull your audio/video cables
through the wall and through the opening in the Easy Mount
Recessed Low Voltage Cable Plate (to help insert larger cables
through the opening in the wall plate, the back scoop of the wall
plate is removable). Now insert the Easy Mount Recessed Low
Voltage Cable Plate flush into the wall. Next, screw down the wall
plate screws with wings. The wings will fasten tightly against the
back of the drywall (see Figure 3) and your installation is
complete.
These Recessed Cable Plates are Designed for Use
with Low Voltage / Data Cables “ONLY”.
Do Not Run or Pull the TV Cord or Other Electrical
Cords Inside the Drywall. National Electrical Code (NEC)
Does Not Allow the Installation of the TV Power Cord or an
Extension Cord Behind the Wall.
CAUTION
Never install low voltage wiring during lightning storms.
Never install low voltage wiring in wet locations
unless the wire is specifically designed for wet
locations.
Never touch un-insulated low voltage wires or
terminals unless the wire has been disconnected at
its source.
Use caution when installing low voltage cables.
IMPORTANT INSTRUCTIONS
Read and understand all instructions.
Follow all warning and instructions marked on the
product.
Do not use this product near water, for example
near a bath tub, wash bowl, kitchen sink, or
laundry tub, in a wet basement, or near a
swimming pool.
SAVE THESE INSTRUCTIONS.
Figure 2 - Front View
Instruction / Installation Sheet
DataComm Electronics 45-0008 & 45-0009 Easy Mount Recessed Low Voltage Cable Plates
This product is patent protected by U.S. Patent numbe
r
7390964
RoHS Compliant
12/01/09 Rev. 1
DataComm Electronics, Inc.
6349 Peachtree Street
Norcross, GA 30071-1725
888.223.7977
770.662.8205
www.datacommelectronics.com
Figure 1
Figure 3 - Back View
45-0008 & 45-0009 – Front View 45-0008 – Back View
Low Voltage Mounting
Bracket Wing
2-5/16”
TEMPLATE
45-0008 & 45-0009
Easy Mount Recessed Low Voltage Cable Plate
ACTUAL SIZE
CUT ALONG DOTTED LINE
Using Template (below),
Cut a Hole in the Drywall
  • Page 1 1

DataComm 45-0009-LA User manual

45-0009-LA
DataComm
Brand
DataComm
Model
45-0009-LA
Category
Electrical wallplates
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents