Avteq GMP-150 Installation guide

Brand: Avteq

Model: GMP-150

Category: Multimedia carts & stands

Type: Installation guide

Avteq GMP-150 is a versatile and mobile multimedia cart designed to accommodate a range of audio-visual equipment, making it ideal for presentations, conferences, and educational settings. Its sturdy construction and adjustable features ensure optimal viewing angles and convenient access to your devices.

GM 150

Easy Setup Guide

x1 x1

x11

Base

Side panels

Top frame

Top

Camera support

Screen mount

support

Screen support

Shelf

Back

cover

Front

glass

Acrylic platform

With break 2

Without break 2

Philips flat head 1/4"

Blind nut 1/4"

Flange nut 1/4"

Philips head bolt

1/4"x 3/4"

Lock

Rack Bolt and nut

Glass hinge

Multi wrench

Hex key



Using the multi wrench V, attach the casters M

to the Base A. Casters with break should be

assembled on front and Locked for easy

assembly.

Front

Back



Adjust the width of one side panel B to

make the flanges fit in the front and back

holes of the base A and press until click.

Screw the philips head bolts R in the base nuts.

Then repeat these steps with the other side panel.

Carriage bolt

Philips head bolt

5/16"x1 1/4"

Leave the sides lose until both the bottom and top

frame are in place.



Place the wider side of the top frame in the front of the

cart and place the slot face down.



Slide the four pins of the top D into

the top frame C following the top

square guides and screw with flange

nut Q from the inside.



To fit the lateral

flange with the top

frame C holes press until click and

secure with bolt R.

Follow these steps in one corner at

a time.

Adjust the lateral

width to make

the flanges fit.

Note: hand tighten bolts then

proceed to step 4, once glass

door is installed then tighten the

bolts for the top frame.

Attach one

hinge S in

the left top

corner of

the front

glass K with

two set

screws with

a flat head

screw

driver.

Make sure

the set

screws are

in the

inside.

Adjust the glass using the set

bolts of each hinge to align it

correctly.

Fit the hinge with the glass in the

top frame hole.

Place the other hinge S in the base A

and slide the glass. Then secure the

glass with the two set screws.



Slide the back cover J flanges into the base A.

Fit the back cover J bracket

into the side panel hole.

Secure the back cover with the

philips head bolt R

First, insert the

cage nut U into the

rack squares at the

desire height from

the inside.

Inside

Outside

Place the shelf I

flanges into the

rack squares.

Screw the shelf with two bolts U

into the cage nuts U.



Compresing the padlock,

lide the lock handle and the washer

thru the cilinder as shown in the sequence.

Then insert it in the glass

with the flange outside and

secure with the plastic nut.



Attach the screen support

H with four philips head

bolts P at the desired

height.

Note: See instructions

inside screen support box

to mount flat screen on

cart.

Attach the acrylic L to

the camera support G

with the philips flat

head bolts O.

Attach the camera

support G at the desired

height with two philips

bolts R.

Place the screen mount support F in the

top D, sliding the flange into the

rectangular hole and fit two carriage

bolts N in the squares.

Fix the mount support F with

flange nuts Q from the inside

of the cart using the multi

wrench V.

NOTE: After finishing, tighten the nuts of the side panels carriage bolts from the

inside.

Avteq GMP-150 Installation guide

Brand: Avteq

Model: GMP-150

Category: Multimedia carts & stands

Type: Installation guide

Download PDF

report

Avteq GMP-150 Installation guide

Avteq GMP-150 Installation guide

Related papers

Other documents