2. Computers & electronics
  3. Cameras & camcorders
  4. Camera accessories
  5. Camera mounting accessories
  6. Displays2go
  7. ELT 2100
ELT 2100

Displays2go ELT 2100, AVT2100L, AVT2100S Operating instructions

  • Hello! I am an AI chatbot trained to assist you with the Displays2go ELT 2100 Operating instructions. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
ELT 2100
Easy Setup Guide
I
t
e
m
s
i
n
c
l
u
d
e
d
x1
x1
A
G
C
D
E
F
H
I
Fixed base
(Not included)
Body
Base
5/16 '' flange nut
Philips flat head
1/4"x3/4''
Casters
Central Camera
support
1
B
I
t
e
m
s
n
o
t
i
n
c
l
u
d
e
d
:
-
P
h
i
l
l
i
p
s
s
c
r
e
w
d
r
i
v
e
r
-
F
i
x
e
d
b
a
s
e
x1
x1
x1
x8
x10
x1
x1
Secure the casters (K) to the base (B)
using the Multi wrench (I)
Attach the base (B) to the body
(A) with the 5/16'' flange nut (E)
and secure the rack with the Phillips
flat head 1/4''x3/4'' (F)
J
K
A
B
x4
x4
Multi wrench
Mount kit
5/16" x 11/4" screw
1" Washer
3/4" Washer
5/16" Nut
2 with break
2 without break
E
F
With Break
K
WHEELED BASE
INSTALLATION
Allen wrench 4mm
Allen wrench 3mm
L
M
N
x4
x1
x1
1/4 '' flange nut
support
Extension camera
support
x1
x1
x4
x2
x1
O
P
Q
Lock
Camera support
Phillips flat
head 1/4 ''
Blind nut 1/4 ''
R
x1
M5X15
2
Adjust mount support
horizontally and
vertically by using
the slots
Attach the base (C) to the body
(A) with the 5/16'' flange nut (E)
and secure the rack with the Phillips
flat head 1/4''x3/4'' (F)
FIXED BASE
INSTALLATION
turn the blind nuts
of the base until
the pedestal is steady
E
Place screen at
desired height
and tighten screws
Use screws kit (J) and follow
screen mount instructions
J
1
Note: Fixed base
not included
C
3
A
D
Adjust camera support
back and forth to the
desired position
Secure with the Knob
Attach support (M) with 1/4''x 1/2 '' screws (F)
to mount and secure with 1/4 '' nut (L)
L
M
F
N
Adjust Extension camera
support (N) up and down
to the desired position
4
Attention: Follow this step in case to use Central camera support
Attention: Follow this step in case to use Extension camera support
O
Secure the
camera support
with kit (O)
Lock installation
R
R
Secure with a Lock screw
Place the lock
Install M5X15 screw
on the Lock
Lock Assembly
1
2
Slide Pull over Cylinder. The Flange
must be as shown in the diagram
Slide Cylinder through hole in
glass as shown in diagram
3
Twist Nut onto Cylinder as
shown in diagram. Ensure that
it’s placed in the correct posi-
tion as shown in diagram.
a
b
c
Nut
Pull
Cilinder
/