2. Office
  3. Office furniture
  4. Multimedia carts & stands
  5. Avteq
  6. GMP-150
GMP-150

Avteq GMP-150 Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Avteq GMP-150 Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • How to assemble the casters of Avteq GMP-150?
    How to adjust the width of the side panel?
    How to secure the top frame?
    How to install the glass door?
    How to adjust the lateral width to make the flanges fit?
    How to attach the shelf?
    How to fix the screen mount support?
GM 150
Easy Setup Guide
I
t
e
m
s
i
n
c
l
u
d
e
d
x1 x1
x1
x1
x1
x4
x2
x4
x4
x2
x11
x6
x1
x8
x1
A
B
C
D
G
F
H
I
J
K
L
M
N
O
P
Q
R
S
V
U
T
Base
Side panels
Top frame
Top
Camera support
Screen mount
support
Screen support
Shelf
Back
cover
Front
glass
Acrylic platform
With break 2
Without break 2
Philips flat head 1/4"
Blind nut 1/4"
Flange nut 1/4"
Philips head bolt
1/4"x 3/4"
Lock
Rack Bolt and nut
Glass hinge
Multi wrench
Hex key
1
Using the multi wrench V, attach the casters M
to the Base A. Casters with break should be
assembled on front and Locked for easy
assembly.
A
M
Front
Back
2
Adjust the width of one side panel B to
make the flanges fit in the front and back
holes of the base A and press until click.
Screw the philips head bolts R in the base nuts.
Then repeat these steps with the other side panel.
Carriage bolt
Philips head bolt
5/16"x1 1/4"
B
I
t
e
m
s
n
o
t
i
n
c
l
u
d
e
d
:
-
P
h
i
l
l
i
p
s
s
c
r
e
w
d
r
i
v
e
r
-
F
l
a
t
h
e
a
d
s
c
r
e
w
d
r
i
v
e
r
Leave the sides lose until both the bottom and top
frame are in place.
3
4
5
Place the wider side of the top frame in the front of the
cart and place the slot face down.
C
B
R
Slide the four pins of the top D into
the top frame C following the top
square guides and screw with flange
nut Q from the inside.
D
C
Q
Q
J
To fit the lateral
flange with the top
frame C holes press until click and
secure with bolt R.
Follow these steps in one corner at
a time.
Adjust the lateral
width to make
the flanges fit.
Note: hand tighten bolts then
proceed to step 4, once glass
door is installed then tighten the
bolts for the top frame.
Attach one
hinge S in
the left top
corner of
the front
glass K with
two set
screws with
a flat head
screw
driver.
Make sure
the set
screws are
in the
inside.
Adjust the glass using the set
bolts of each hinge to align it
correctly.
Fit the hinge with the glass in the
top frame hole.
Place the other hinge S in the base A
and slide the glass. Then secure the
glass with the two set screws.
K
6
J
Slide the back cover J flanges into the base A.
Fit the back cover J bracket
into the side panel hole.
Secure the back cover with the
philips head bolt R
.
7
First, insert the
cage nut U into the
rack squares at the
desire height from
the inside.
Inside
Outside
Place the shelf I
flanges into the
rack squares.
Screw the shelf with two bolts U
into the cage nuts U.
8
I
Compresing the padlock,
s
lide the lock handle and the washer
thru the cilinder as shown in the sequence.
Then insert it in the glass
with the flange outside and
secure with the plastic nut.
9
10
Attach the screen support
H with four philips head
bolts P at the desired
height.
Note: See instructions
inside screen support box
to mount flat screen on
cart.
Attach the acrylic L to
the camera support G
with the philips flat
head bolts O.
11
Attach the camera
support G at the desired
height with two philips
bolts R.
H
P
O
G
L
R
12
Place the screen mount support F in the
top D, sliding the flange into the
rectangular hole and fit two carriage
bolts N in the squares.
Fix the mount support F with
flange nuts Q from the inside
of the cart using the multi
wrench V.
F
N
Q
NOTE: After finishing, tighten the nuts of the side panels carriage bolts from the
inside.
/