Minka Group 3396-754 User manual

Minka Group
Brand
Minka Group
Model
3396-754
Type
User manual

Minka Group 3396-754 is a versatile and stylish lighting fixture that can elevate the ambiance of any room. With its adjustable height and multiple bulb capacity, it offers customizable lighting solutions for various spaces. The fixture supports up to six candelabra base bulbs of up to 60 watts each, allowing you to tailor the brightness and warmth to your preference. Whether you seek ambient lighting for a cozy living room or task lighting for a home office, this fixture can adapt to meet your needs.

Minka Group 3396-754 is a versatile and stylish lighting fixture that can elevate the ambiance of any room. With its adjustable height and multiple bulb capacity, it offers customizable lighting solutions for various spaces. The fixture supports up to six candelabra base bulbs of up to 60 watts each, allowing you to tailor the brightness and warmth to your preference. Whether you seek ambient lighting for a cozy living room or task lighting for a home office, this fixture can adapt to meet your needs.

INSTALLATION INSTRUCTIONS
Item#3394-754 3395-754 3396-754 (New.05/29/2023)
READ AND SAVE THESE INSTRUCTIONS
W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Page 1/2
Fig. 1
Fig. 2
PREPARATION (Fig. 1)
1.
Shut off power at the fuse box or circuit breaker box and
remove the old fixture including the mounting hardware.
2. Carefully unpack your new fixture and lay out all the parts
in a clean area. Take care not to misplace any small parts
necessary for installation.
ASSEMBLING THE FIXTURE (Fig.1&Fig.3)
3. Screw cluster (I) onto rod (H). Pass the wires carefully
through swivel (G) and screw the another end of rod (H) to
swivel (G).
4. Determine the desired hanging height.
Pass the wires
carefully through each rod as you assembled. Thread
one
end of rods (E1 or E2) to coupling (F) and secure the other
end of rod (E1 or E2) to swivel (D).
5. Position mounting plate (A) on the ceiling and mark the
location of two plastic anchors (L). Pre-drill the holes for
plastic anchors (L). Insert
plastic anchors (L) into the
ceiling.
6. Attach mounting plate (A) to the junction box (not included)
with junction box screws (B) (Size: #8-32N*L1”) and
wood
screw (N) into plastic anchors (L)
. The side of the mounting
plate (A)
with “GND” marked on it and two convex points
must face out.
7. Support cable is provided to support weight of fixture while
wiring. Align fixture to mounting plate (A
) and attach hook
(J) on the end of support
mounting plate (A
). Carefully allow support cable to support
weight of fixture while wiring (Fig.1 Fig3).
CONNECTING THE WIRES (Fig. 2)
8.
Connect the electrical wires as shown in fig.2, making sure
that all wire connecto
rs are secured. If junction box has a
ground wire (green or bare copper), connect the fixture’s
ground wire to it. Otherwise, connect the fixture’s ground
wire directly to mounting plate (A) using the green screw
provided.
9. Tuck the wire connectors neatly into the junction box.
COMPLETING THE INSTALLATION (Fig. 1)
10. Raise canopy (C)
and align the holes with mounting plate
(A) and secure with mounting screws (K) (Size:
#8-32N*L0.5”).
11. Install candelabra base bulbs 【3394-754 four (4) pcs,
3395-754 five (5) pcs, 3396-754 six (6) pcs】
up to 60 watts
each or CFL or LED equivalent (not included) in
accordance with the fixture specification—
DO NOT
EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS
DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)
Your installation is now complete. Return power to the junction
box and test the fixture.
Note:
Illustration (Fig. 1) on this manual is for installation
purposes only. It may or may not be identical to the fixture
purchased.
Set#A-022-145 Candle Cover# CCV20076P-754
Mounting Plate x1pc
Ground Screw x1pc
Junction box Screw x2pcs
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
Green
(Ground)
LA-3279E
Rod#
E1.W35-H-754
E2. W35-1-754
Fig.3
Pa
Page 2/2
LA-3279E
a. Hardware Bag
A. Mounting Plate x 1pc
B. Junction Box
Screw x 2pcs
C. Canopy x 1pc
K. Mounting Screw x 2pcs
L. Plastic Anchor x 2pcs
N. Wood Screw x 2pcs
E1 E
2
b. Hardware Bag
E1. Rod 6” x1pc
E2. Rod 12” x3pcs
A
B
C
K
L
B
C
D
E1 E2
J
K
L
A
N
N
  • Page 1 1
  • Page 2 2

Minka Group 3396-754 User manual

Minka Group
Brand
Minka Group
Model
3396-754
Type
User manual

Minka Group 3396-754 is a versatile and stylish lighting fixture that can elevate the ambiance of any room. With its adjustable height and multiple bulb capacity, it offers customizable lighting solutions for various spaces. The fixture supports up to six candelabra base bulbs of up to 60 watts each, allowing you to tailor the brightness and warmth to your preference. Whether you seek ambient lighting for a cozy living room or task lighting for a home office, this fixture can adapt to meet your needs.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents