Dahua ISC-D218 User manual

Brand: Dahua

Model: ISC-D218

Type: User manual

This manual is also suitable for

ISC-D206

Dahua ISC-D218 is a high-performance security gate, featuring high metal detection sensitivity, light weight, strong anti-interference, and stable performance. It uses high-strength special materials, making it light-weighted and easy to transport and install. With its modular design, the device ensures good stability and delivers an intuitive interface for simple use. The ISC-D218 utilizes electromagnetic field to detect carry-on metal articles, triggering sound and light alarms when the detected metal exceeds a certain amount. It consists of a host, a high-frequency signal generator, a signal receiver, and an infrared sensor. The device stands out with its elegant appearance, robust metal detection capability, multiple detection zones, a unique Internet remote management system, and lightweight design.

Walk-through Metal Detector

Quick Start Guide

V1.0.0

Foreword

General

This manual introduces the functions and operations of the walk-through metal detector

(hereinafter referred to as "the Device").

Models

ISC-D206, ISC-D218

Safety Instructions

The following categorized signal words with defined meaning might appear in the manual.

Signal Words

Meaning

DANGER

Indicates a high potential hazard which, if not avoided, will result

in death or serious injury.

WARNING

Indicates a medium or low potential hazard which, if not avoided,

could result in slight or moderate injury.

CAUTION

Indicates a potential risk which, if not avoided, could result in

property damage, data loss, lower performance, or unpredictable

result.

TIPS

Provides methods to help you solve a problem or save you time.

NOTE

Provides additional information as the emphasis and supplement

to the text.

Revision History

Version

Revision Content

Release Time

V1.0.0

First release.

November 2020

Interface Declaration

This manual mainly introduces the relevant functions when you use the Device. The

interfaces used for manufacture, returning to the factory for inspection, and locating fault are

not described in this manual. Please contact technical support if you need information about

these interfaces.

About the Manual

 The manual is for reference only. If there is inconsistency between the manual and the

actual product, the actual product shall prevail.

III

 We are not liable for any loss caused by the operations that do not comply with the

manual.

 The manual would be updated according to the latest laws and regulations of related

jurisdictions. For detailed information, refer to the paper manual, CD-ROM, QR code or

our official website. If there is inconsistency between paper manual and the electronic

version, the electronic version shall prevail.

 All the designs and software are subject to change without prior written notice. The

product updates might cause some differences between the actual product and the

manual. Please contact the customer service for the latest program and supplementary

documentation.

 There still might be deviation in technical data, functions and operations description, or

errors in print. If there is any doubt or dispute, we reserve the right of final explanation.

 Upgrade the reader software or try other mainstream reader software if the manual (in

PDF format) cannot be opened.

 All trademarks, registered trademarks and the company names in the manual are the

properties of their respective owners.

 Please visit our website, contact the supplier or customer service if there is any problem

occurring when using the device.

 If there is any uncertainty or controversy, we reserve the right of final explanation.

Important Safeguards and Warnings

This chapter describes the contents covering proper handling of the Device, hazard

prevention, and prevention of property damage. Read these contents carefully before using

the Device, comply with them when using, and keep the manual well for future reference.

Operation Requirement

 Do not place or install the Device in a place exposed to sunlight or near the heat source.

 Keep the Device away from dampness, dust or soot.

 Keep the Device installed horizontally on the stable place to prevent it from falling.

 Do not drop or splash liquid onto the Device, and make sure there is no object filled with

liquid on the Device to prevent liquid from flowing into the Device.

 Install the Device in a well-ventilated place, and do not block the ventilation of the

Device.

 Operate the Device within the rated range of power input and output.

 Do not disassemble the Device.

 Transport, use and store the Device under the allowed humidity and temperature

conditions.

Electrical Safety

 Use the battery of specified manufacturer; otherwise there might result in explosion.

When replacing battery, make sure the same type is used. Improper battery use might

result in fire, explosion, or inflammation.

 Always replace with the same type of batteries.

 Use the recommended power cables in the region and conform to the rated power

specification.

 Use the power adapter provided with the Device; otherwise, it might result in people

injury and device damage.

 The power source shall conform to the requirement of the Safety Extra Low Voltage

(SELV) standard, and supply power with rated voltage which conforms to Limited power

Source requirement according to IEC60950-1. Please note that the power supply

requirement is subject to the device label.

 Connect the Device (I-type structure) to the power socket with protective earthing.

 The appliance coupler is a disconnection device. When using the coupler, keep the angle

for easy operation.

Table of Contents

Foreword ................................................................................................................................................... II

Important Safeguards and Warnings .................................................................................................... IV

1 Overview ................................................................................................................................................. 1

Introduction ................................................................................................................................... 1 1.1 Detection Zones ............................................................................................................................ 1 1.2 Technical Advantages ................................................................................................................... 1 1.3 Application Scenario ..................................................................................................................... 2 1.4

2 Installation .............................................................................................................................................. 3

Checking List ................................................................................................................................. 3 2.1 Structure ........................................................................................................................................ 3 2.2 Installation Environment ................................................................................................................ 4 2.3 Installing the Device ...................................................................................................................... 5 2.4

3 Configuration ......................................................................................................................................... 9

ISC-D206 ...................................................................................................................................... 9 3.1 3.1.1 Configuration Panel ............................................................................................................ 9

3.1.2 Basic Operations .............................................................................................................. 10

3.1.3 Configuring Function ......................................................................................................... 11

ISC-D218 .................................................................................................................................... 12 3.2 3.2.1 Configuration Panel .......................................................................................................... 12

3.2.2 Basic Operations .............................................................................................................. 13

4 Troubleshooting .................................................................................................................................. 16

Error Code (ISC-D218) ............................................................................................................... 16 4.1 Troubleshooting........................................................................................................................... 17 4.2 Cybersecurity Recommendations ................................................................................... 19 Appendix 1

1 Overview

Introduction 1.1

Walk-through metal detector is a high-performance security gate. The Device has high metal

detection sensitivity, light weight, strong anti-interference, and stable performance. It uses

high-strength special materials which is light-weighted and easy to transport and install. The

Device has a modular design and is manufactured on the unified assembly lines, so it can

ensure the good stability. It also delivers intuitive interface and simple use, so no operation

training is required to use it.

The Device can be widely used in sports meetings, conferences, schools and other occasions.

It adopts electromagnetic field to detect carry-on metal articles, and uses sound and light alarm

to indicate that the carry-on metal is more than a certain amount. It consists of a host, a

high-frequency signal generator, a signal receiver, and an infrared sensor, with a beautiful

appearance, strong metal detection capability, multiple detection zones, a unique Internet

remote management system, and light weight. It is currently a leading metal detection door in

the market.

Detection Zones 1.2

Detection zones

Figure 1-1

No.

Number of Zones

33-zone

18-zone

6-zone

Technical Advantages 1.3

 Start-stop Technology

The IR units support manual start-stop technology for longer service life.

 Sensitivity Adjustable

The sensitivity of each detection zone can be adjusted as needed to meet different

sensitivity requirements of different zones.

 Alarm

Light and sound alarm for sharp alert. The sound duration and volume can be adjusted as

needed.

 Query

The system supports real-time query.

 Detection Capability

60 to 100 people detected per min.

 Filtering

Pre-define metal item weight, volume, size, part; exclude keys, jewelries, belt buckles and

more.

 Security Protection

In line with EMC electromagnetic radiation standards and adopting weak magnetic field

technology, the device is harmless to cardiac pacemaker wearers, pregnant women, floppy

disks, film, and videotapes.

Application Scenario 1.4

The Device is used to detect the metal items carried by the person going through the detection

door.

Typical application scenarios include:

 Airports, ports: Passenger inspection.

 Court: Visitors inspection.

 Prison: Visitors inspection.

 Meetings, public buildings, sports competitions: Participants inspection.

 Power plant: Employees and visitors inspection.

 Factory: Anti-theft.

 Hotels, restaurants, entertainment venues, ballrooms: Visitors inspection.

The manufacturer is not responsible if the Device is used for purposes other than those

described above.

The design and manufacture of the Device is based on long-term practice and research. The

equipment is designed to be secure and, based on existing knowledge, does not pose any

health hazard to personnel passing through the security gates when operating in accordance

with the instructions.

2 Installation

Checking List 2.1

After receiving your product, check against the table below. If there are any problems, contact

the after-sales service personnel.

Table 2-1 Checking list

Order

List

Description

Overall

packaging

Appearance

Obvious damage

Packaging

Accidental impact

Accessories (list of

accessories on

warranty card)

Complete or not

Host

Appearance

Obvious damage

Model

Whether consistent with the order

contract

Structure 2.2

Dimensions (Unit: mm [inch]) Figure 2-1

Table 2-2 Description

Parameter

Description

Overall Exterior Size

2170 mm × 845 mm × 465 mm

Passageway Interior Size

2015 mm × 688 mm × 368 mm

Packing Size

2409 mm × 868 mm × 303.5 mm

Net Weight

38 kg

Gross Weight

43 kg

Operating Voltage

90V–240V AC 50/60Hz

Power Consumption

13W

Operating Temperature

-20°C to +65°C (-4°F to +149°F)

Operating Humidity

0%–95%

Storage Temperature

-20°C to +70°C (-4°F to +158°F)

Storage Humidity

0%–90% RH

Installation Environment 2.3

 The ground is flat and sturdy

The ground should be flat and firmly supporting to prevent vibration. If there is a vibrating

metal structure under the ground, there can be unnecessary alarm when people passing

through the metal detection door.

 Keep away from fixed metal objects

Large metal objects that are fixed or immobile should be at least 10 cm away from the

detection door (detecting large metal objects) because they might make the Device more

susceptible to vibration.

The distance in this section is the recommended distance. The actual installation distance

depends on the installation site conditions.

 Keep away from moving metal objects

Large moving metal objects should be kept 0.5 m to 2 m away from the detection door to

avoid false alarms. Depending on the size of the metal object, the distance between the

moving metal object and the detection door might vary.

 Keep away from radioactive electronic interference

The distance between the electronic interference source and the receiving coil should be

maximum. The recommended minimum distance is 0.5 m to 4 m. However, the actual

distance needs to be based on specific circumstances. For example, you can go through a

metal detector door with a source of interference until the best position is found.

Interference can occur from electronic control panels, radios and computers, image

displays, high-power motors and transformers, AC wires, transistor control circuits, flash

fluorescent tubes, arc welding equipment, and more.

 Keep away from conductive electronic interference

Connect the power cord to a line that is not connected to other large loads, such as

high-power motors. Because they can cause a large power or voltage shock in the line.

Installing the Device 2.4

Check whether the package is complete and open the box. Step 1 Open the box Figure 2-2

Take out the left and right door panels from the box. Step 2 Take out door panels Figure 2-3

Take out the manual, beam, host box, and power supply from the box. Step 3

Take out manual, beam, main box, and power supply Figure 2-4

Follow the previous figure to prepare the door panels, beams, host box, and bolts. Step 4 Prepare the parts and the tools Figure 2-5

Install the beams and the host box. Step 5 Install the beams and the host box Figure 2-6

Connect the detection wire on the host box to the left and right door panels. Step 6 Connect the detection wire Figure 2-7

Stand the Device up. Step 7 Stand the Device up. Figure 2-8

Connect the power supply to the Device, and then turn on the power switch to start the Step 8 Device.

Start the Device Figure 2-9

3 Configuration

ISC-D206 3.1

3.1.1 Configuration Panel

Single-zone panel (ISC-D206) Figure 3-1

Single-zone panel description (ISC-D206) Figure 3-2

No.

Name

①

Four-in-one digital tube.

②

Four-in-one digital tube.

③

Working indicator light.

④

Save and exit.

⑤

–

⑥

⑦

Program.

⑧

Pass indicator light.

⑨

Alarm indicator light.

4/6/L6-zone digital panel (ISC-D206) Figure 3-3

4/6/L6-zone panel description (ISC-D206) Figure 3-4

No.

Name

①

Four-in-one digital tube.

②

Four-in-one digital tube.

③

Working indicator light.

④

Power button.

⑤

–

⑥

⑦

Program.

3.1.2 Basic Operations

Starting the Device

Connect the power supply, press and hold the Reset/Switch button, and then the Device starts

and enters the working state, and shows "0000 0000".

Entering Password

When the screen shows "0000 0000", press Program, and then the screen shows "P 0000".

enter the password, press + to change the value of the corresponding bit (0 to 9 in cycle), press

To change the bit, press –. If the password is correct, press Program to go next; otherwise you

cannot go next, and the Device shows "P 0000".

Keep your password in mind.

Changing Password

When the screen shows "0000 0000" after power-on, press and hold Program for 3 s. Step 1 When the screen displays "P 0000", enter the old password (press – to change the bit, Step 2 and press + to change the value).

Press Program, and then the screen displays "C- - - - ". Press +, and then the screen Step 3 shows "P 0000".

Enter the new password (press – to change the bit, and press + to change the value), Step 4 and then press Program to save and go next.

Change password Figure 3-5

3.1.3 Configuring Function

Configure functions and parameters.

 The values that you set at last are automatically saved when you go to the next interface.

 Press Program to save when finishing each configuration.

Function configuration Figure 3-6

Table 3-1 Function description

No.

Function description

①

Number of passes.

②

Number of alarms.

③

Function configuration.

④

Parameter configuration.

 To select a function, press PROG/Program.

 To set a value, press to increase and to reduce.

Table 3-2 Single-zone function parameter configuration

Function

Parameter

Description

Enter password

—

Configure operating

frequency

1–50

50 levels available.

Configure detector

sensitivity

0–99

100 levels available.

Table 3-3 4/6/L6-zone function parameter configuration

Function

Parameter

Description

Configure security

level

1–20

20 levels available.

Configure operating

frequency

1–50

50 levels available.

Configure zone

sensitivity

0–200

200 levels available for Zone 1.

0–200

200 levels available for Zone 2.

0–200

200 levels available for Zone 3.

0–200

200 levels available for Zone 4.

0–200

200 levels available for Zone 5.

…

Configure the

duration of the alarm

sound

1–3

3 levels available.

Configure alarm

volume

0–2

2 levels available.

Configure alarm tone

1–10

10 levels available.

ISC-D218 3.2

3.2.1 Configuration Panel

Panel (LED screen) (ISC-D218) Figure 3-7

Panel description (ISC-D218) Figure 3-8

No.

Name

②

Five-in-one green digital tube

②

Five-in-one red digital tube

③

Two-in-one green digital tube; Three-in-one red digital tube

④

⑤

–

⑥

Save and exit

No.

Name

⑦

Working indicator light

⑧

Program

⑨

Power button

Table 3-4 Functions description (ISC-D218)

Function

Description

Start

Press ⑨.

Power-on

Self-test

Self-tests 12 detectors on the left and right door panels after power-on. An



error message is prompted if a fault is discovered.

Self-tests the IR sensor after power-on. The error message LR ERR is



prompted if a fault is discovered.

Self-tests the SD card after power-on. The error message s d ERR is



prompted if a fault is discovered.

Enter

password

To enter the password, press ④ to change the number of the corresponding bit

(0 to 9 in cycle). Press ⑤ to change the bit. If the password is wrong, you get

the prompt C333. Press ⑥ and enter the password again. Only when the

password is correct can you press ⑧ to enter the parameter adjustment

interface.

Change

password

If you need to change the password, press ⑧ for 5 s, and then the

corresponding bit began to flash. Press ④ to change the value of the

corresponding bit (0 to 9 in cycle). Press ⑤ to change the bit, and then you can

enter a new password. Press ⑧ to save and enter the next level of setting.

3.2.2 Basic Operations

Configure functions and parameters.

Configure functions Figure 3-9

Description

Figure 3-10

No.

Name

①

Number of passersby.

②

Number of alarm times.

③

Device setting display.

④

Function selection.

⑤

Parameter configuration.

 To select a function, press ⑧.

 To set parameter values, press ④ to increase, and press ⑤ to reduce.

Table 3-5 6/12/18-zone parameter configuration

Function

Parameter

Description

Configure operating

frequency

1–50

50 levels available.

Configure security level

0–99

100 levels available.

Configure zones

6/12/18

Three zone divisions are available.

Configure detector

sensitivity on the left

0–399

400 levels available for Detector 1.

0–399

400 levels available for Detector 2.

0–399

400 levels available for Detector 3.

0–399

400 levels available for Detector 4.

0–399

400 levels available for Detector 5.

…

Configure detector

sensitivity on the right

0–399

400 levels available for Detector 1.

0–399

400 levels available for Detector 2.

0–399

400 levels available for Detector 3.

0–399

400 levels available for Detector 4.

0–399

400 levels available for Detector 5.

…

Configure alarm volume

0–99

100 levels available.

Configure alarm tone

0–99

100 levels available.

Configure the duration of

the alarm sound

0–99

100 levels available.

Configure scenarios

1–72

72 scenarios available.

Configure column light

Ld 0 by

default

Change to Ld 1 when the left and right door

column lights are reversed.

Battery level

0–100

Displays battery level.

Automatic frequency

hopping

1–50

Automatically applies the suitable frequency.

Configure IR on/off

—

4 IR modes available.

Change password

***

Change password.

Table 3-6 Scenario number

No.

Scenario

No.

Scenario

No.

Scenario

Court

Celebration

Embassy

Prison

Entertainment venue

Power plant

Procuratorate

Performance venue

Hotel

Customs

KTV

Swimming pool

Border

Bar

Public security

bureau

Government buildings

Shopping mall

Bureau of letters and

visits

Airport

Fire fighting

Drug treatment center

High-speed rail

station

Ammunition depot

Exam place

No.

Scenario

No.

Scenario

No.

Scenario

Railway station

Gold and silver

jewelry

Courtroom

Bus station

Electroplating plant

Food factory

Wharf

Die casting

Bank.

Reeducation-through-

labor center

Precious metal

Vault

Printing plant

Communication room

Convention and

Exhibition Center

Metals factory

Meeting room

Subway station

Electronics factory

VIP room

Villa

Precision instrument

factory

Office

Community

Industry mine

Rescue station

Opera house

Oil depot

Club

Cinema

Research and

development center

Library

School

Archives office

Radio and television

station

Laboratory

Museum

Hospital

Detention house

Safe room

Weather stations

Asylum

Gym

Radar station

Gallery

Venue

Troops base

Amusement park

Page is loading ...

Dahua ISC-D218 User manual

Brand: Dahua

Model: ISC-D218

Type: User manual

This manual is also suitable for

ISC-D206

Download PDF

report

Dahua ISC-D218 User manual

This manual is also suitable for

Dahua ISC-D218 User manual

Related papers

Other documents