Avid Pro Tools 11.2 User guide

MachineControl

™

Guide

Version 11.2

Legal Notices

This guide may not be duplicated in whole or in part without

the written consent of Avid.

003, 192 Digital I/O, 192 I/O, 96 I/O, 96i I/O, Adrenaline,

AirSpeed, ALEX, Alienbrain, AME, AniMatte, Archive,

Archive II, Assistant Station, AudioPages, AudioStation,

AutoLoop, AutoSync, Avid, Avid Active, Avid Advanced

Response, Avid DNA, Avid DNxcel, Avid DNxHD, Avid DS

Assist Station, Avid Ignite, Avid Liquid, Avid Media Engine,

Avid Media Processor, Avid MEDIArray, Avid Mojo,

Avid Remote Response, Avid Unity, Avid Unity ISIS,

Avid VideoRAID, AvidRAID, AvidShare, AVIDstripe, AVX,

Beat Detective, Beauty Without The Bandwidth,

Beyond Reality, BF Essentials, Bomb Factory, Bruno, C|24,

CaptureManager, ChromaCurve, ChromaWheel,

Cineractive Engine, Cineractive Player, Cineractive Viewer,

Color Conductor, Command|8, Control|24, Cosmonaut Voice,

CountDown, d2, d3, AAE, D-Command, D-Control, Deko,

DekoCast, D-Fi, D-fx, Digi 002, Digi 003, DigiBase,

Digidesign, Digidesign Audio Engine, Digidesign

Development Partners, Digidesign Intelligent Noise

Reduction, Digidesign TDM Bus, DigiLink, DigiMeter,

DigiPanner, DigiProNet, DigiRack, DigiSerial, DigiSnake,

DigiSystem, Digital Choreography, Digital Nonlinear

Accelerator, DigiTest, DigiTranslator, DigiWear, DINR,

DNxchange, Do More, DPP-1, D-Show, DSP Manager,

DS-StorageCalc, DV Toolkit, DVD Complete, D-Verb, Eleven,

EM, Euphonix, EUCON, EveryPhase, Expander,

ExpertRender, Fairchild, FastBreak, Fast Track, Film Cutter,

FilmScribe, Flexevent, FluidMotion, Frame Chase, FXDeko,

HD Core, HD Process, HDpack, Home-to-Hollywood,

HyperSPACE, HyperSPACE HDCAM, iKnowledge, Impact,

Improv, iNEWS, iNEWS Assign, iNEWS ControlAir, InGame,

Instantwrite, Instinct, Intelligent Content Management,

Intelligent Digital Actor Technology, IntelliRender, Intelli-Sat,

Intelli-Sat Broadcasting Recording Manager, InterFX,

Interplay, inTONE, Intraframe, iS Expander, iS9, iS18, iS23,

iS36, ISIS, IsoSync, LaunchPad, LeaderPlus, LFX, Lightning,

Link & Sync, ListSync, LKT-200, Lo-Fi, MachineControl,

Magic Mask, Make Anything Hollywood,

make manage move|media, Marquee, MassivePack,

MassivePack Pro, Maxim, Mbox, Media Composer,

MediaFlow, MediaLog, MediaMix, Media Reader,

Media Recorder, MEDIArray, MediaServer, MediaShare,

MetaFuze, MetaSync, MIDI I/O, Mix Rack, Moviestar,

MultiShell, NaturalMatch, NewsCutter, NewsView,

NewsVision, Nitris, NL3D, NLP, NSDOS, NSWIN, OMF,

OMF Interchange, OMM, OnDVD, Open Media Framework,

Open Media Management, Painterly Effects, Palladiium,

Personal Q, PET, Podcast Factory, PowerSwap, PRE,

ProControl, ProEncode, Profiler, Pro Tools, Pro Tools|HD,

Pro Tools LE, Pro Tools M-Powered, Pro Transfer,

QuickPunch, QuietDrive, Realtime Motion Synthesis,

Recti-Fi, Reel Tape Delay, Reel Tape Flanger,

Reel Tape Saturation, Reprise, Res Rocket Surfer, Reso,

RetroLoop, Reverb One, ReVibe, Revolution, rS9, rS18,

RTAS, Salesview, Sci-Fi, Scorch, ScriptSync,

SecureProductionEnvironment, Shape-to-Shape,

ShuttleCase, Sibelius, SimulPlay, SimulRecord,

Slightly Rude Compressor, Smack!, Soft SampleCell,

Soft-Clip Limiter, SoundReplacer, SPACE, SPACEShift,

SpectraGraph, SpectraMatte, SteadyGlide, Streamfactory,

Streamgenie, StreamRAID, SubCap, Sundance,

Sundance Digital, SurroundScope, Symphony, SYNC HD,

SYNC I/O, Synchronic, SynchroScope, Syntax,

TDM FlexCable, TechFlix, Tel-Ray, Thunder, TimeLiner,

Titansync, Titan, TL Aggro, TL AutoPan, TL Drum Rehab,

TL Everyphase, TL Fauxlder, TL In Tune, TL MasterMeter,

TL Metro, TL Space, TL Utilities, tools for storytellers, Transit,

TransJammer, Trillium Lane Labs, TruTouch, UnityRAID,

Vari-Fi, Video the Web Way, VideoRAID, VideoSPACE,

VTEM, Work-N-Play, Xdeck, X-Form, and XMON are either

registered trademarks or trademarks of Avid Technology, Inc.

in the United States and/or other countries.

Bonjour, the Bonjour logo, and the Bonjour symbol are

trademarks of Apple Computer, Inc.

Thunderbolt and the Thunderbolt logo are trademarks of Intel

Corporation in the U.S. and/or other countries.

This product may be protected by one or more U.S. and non-

U.S. patents. Details are available at www.avid.com/patents.

Product features, specifications, system requirements, and

availability are subject to change without notice.

Guide Part Number 9329-65434-00 REV A 05/14

Contents iii

Chapter 1. Introduction .........................................................1

MachineControl Version 2.0 for Pro Tools | HD Software 11 ..........................1

MachineControl Components ................................................1

System Requirements and Compatibility ........................................2

Registration .............................................................2

Conventions Used in This Guide..............................................3

About www.avid.com ......................................................3

Chapter 2. Installing MachineControl..............................................5

Cables and Connections ...................................................5

Connecting Machines......................................................7

Authorizing MachineControl .................................................8

Removing MachineControl ..................................................9

Starting Up Your System ...................................................9

Chapter 3. MachineControl Communication Modes .................................11

Serial Deck Control Mode..................................................11

Remote 9-Pin Deck Emulation Mode..........................................12

Chapter 4. Setting Up Machine Control ...........................................13

Online and Offline Operation ...............................................13

Transport Controls .......................................................13

Remote Mode ..........................................................15

Chapter 5. Serial Deck Control Mode .............................................17

Configuring Pro Tools | Software for Serial Deck Control (Overview)...................17

Configuring a MachineControl Device for Deck Control ............................17

Preferences for Serial Deck Control Mode......................................19

Session Setup Window and MachineControl ....................................21

Additional Pro Tools Commands.............................................24

Selecting Pro Tools or the Machine as the Transport Master ........................25

Contents

MachineControl Guideiv

Playback in Serial Deck Control Mode ........................................ 26

Remote Track Arming .................................................... 28

Configuring Track Arming ................................................. 28

Creating a Track Arming Profile ............................................. 29

Arming Tracks Remotely for Layback ......................................... 32

Chapter 6. Remote 9-Pin Deck Emulation Mode.................................... 33

Configuring Remote 9-Pin Deck Emulation Mode ................................ 33

Preferences for Remote 9-Pin Deck Emulation Mode ............................. 36

Playback in Remote 9-Pin Deck Emulation Mode ................................ 37

Recording in Remote 9-Pin Deck Emulation Mode ............................... 37

Track Arming in Remote 9-Pin Deck Emulation Mode ............................. 38

Chapter 7. Using a Paddle Device in Local Mode................................... 39

Connecting a Supported Third-Party Paddle Device to Your Pro Tools System........... 39

Allow Track Arm Commands in Local Mode Preference ........................... 39

Configuring Ports for a Deck and a Supported Third-Party Paddle Device .............. 40

Appendix A. Deck Control Key Commands ....................................... 41

Appendix B. Troubleshooting .................................................. 43

Appendix C. Machine IDs ...................................................... 45

Appendix D. 9-Pin Cable Pinouts................................................ 47

Chapter 1: Introduction 1

Chapter 1: Introduction

MachineControl

™

software option for

Pro Tools

®

| Software enables serial communica-

tion with Sony

®

9-pin compatible synchronizers,

and video or audio machines.

MachineControl Version 2.0

for

Pro Tools | HD Software 11

This guide provides installation and operational in-

structions for MachineControl version 2.0 for

Pro Tools

®

| HDX and Pro Tools

®

| HD Native

systems running Pro Tools

®

| HD Software 11.

If you require documentation for other system con-

figurations, refer to earlier versions of this guide,

available in the Knowledge Base. You can reach

the Knowledge Base by clicking

Help >

Pro Tools Knowledge Base

in Pro Tools, or by

visiting www.avid.com/support.

MachineControl Components

Your MachineControl package includes the

following, based on your operating system:

Mac Systems

• MachineControl Installer disc

• Serial Deck Control cable: Male 8-pin

mini-DIN to male 9-pin cable

• Remote 9-pin Deck Emulation cable: Male 8-

pin mini-DIN to female 9-pin cable

• MachineControl iLok Activation Card

Windows Systems

• MachineControl Installer disc

• Serial Deck Control cable: RS-232 to RS-422

• 9-pin Turnaround adapter (for Remote 9-pin

Deck Emulation mode)

• MachineControl iLok Activation Card

MachineControl Guide2

System Requirements and

Compatibility

MachineControl requires a qualified

Pro Tools | HDX and Pro Tools | HD Native

systems.

Avid can only assure compatibility and provide

support for hardware and software it has tested and

approved.

For complete system requirements and a list of

qualified computers, operating systems, hard

drives, and third-party devices, visit:

www.avid.com/compatibility

Serial Deck Control Mode

Requirements

For Tighter Lockups

 For Serial Deck Control, use of a SYNC periph-

eral (Pro Tools

®

| SYNC HD) is recommended.

 For near sample accurate Serial Deck Control, a

SYNC peripheral is required.

 If you are not using a SYNC peripheral with

Pro Tools, some features of MachineControl can

be used by connecting the deck to the computer

with the proper cable and adapter configuration.

Remote 9-Pin Deck Emulation

Requirements

A SYNC peripheral is required when running

MachineControl 9-Pin Remote Deck Emulation

mode, as it provides frame-accurate LTC.

Registration

Review the enclosed Registration Information

Card and follow the instructions on it to quickly

register your purchase online. By registering, you

become eligible to receive the following:

• Technical support information

• Software update and upgrade notices

• Hardware warranty information

See “Connecting Machines for

Serial Control Mode” on page 7.

Remote 9-Pin Deck Emulation does not work

using the serial ports on a SYNC peripheral or

using the Serial port on an HDX card,

HD Native card, or HD Native Thunderbolt.

Instead, you must connect the remote control-

ler to your Pro Tools system using one of the

methods detailed in “Connecting Machines

for Remote 9-Pin Deck Emulation Mode” on

page 7.

Chapter 1: Introduction 3

Conventions Used in This

Guide

All of our guides use the following conventions to

indicate menu choices and key commands:

:

The names of Commands, Options, and Settings

that appear on-screen are in a different font.

The following symbols are used to highlight

important information:

About www.avid.com

The Avid website (www.avid.com) is your best

online source for information to help you get the

most out of your Pro Tools system. The following

are just a few of the services and features available.

Product Registration

Register your purchase

online.

Support and Downloads

Contact Avid Customer

Success (technical support); download software

updates and the latest online manuals; browse the

Compatibility documents for system requirements;

search the online Knowledge Base or join the

worldwide Pro Tools community on the User Con-

ference.

Training and Education

Study on your own using

courses available online or find out how you can

learn in a classroom setting at a certified Pro Tools

training center.

Products and Developers

Learn about Avid

products; download demo software or learn about

our Development Partners and their plug-ins, ap-

plications, and hardware.

News and Events

Get the latest news from Avid or

sign up for a Pro Tools demo.

Convention Action

File > Save Choose Save from the

File menu

Control+N Hold down the Control key

and press the N key

Control-click Hold down the Control key

and click the mouse button

Right-click Click with the right

mouse button

User Tips are helpful hints for getting the

most from your system.

Important Notices include information that

could affect your data or the performance of

your system.

Shortcuts show you useful keyboard or mouse

shortcuts.

Cross References point to related sections in

this guide and other Pro Tools guides.

MachineControl Guide4

Chapter 2: Installing MachineControl 5

Chapter 2: Installing MachineControl

Before you install MachineControl, make sure that

you have already connected and verified operation

of your Pro Tools system. If you are using a

SYNC HD, refer to the

SYNC HD Guide to make

sure your equipment is installed and operating cor-

rectly.

Cables and Connections

MachineControl requires its own connections be-

tween Pro Tools hardware, the computer, and ex-

ternal machines. Connections differ depending on

your Pro Tools audio interface, operating system,

and on which of the two MachineControl opera-

tional modes you want to use: Serial Deck Control

mode or Remote 9-Pin Deck Emulation mode.

Cables

MachineControl comes with the following cables

and adapters, depending on your computer plat-

form:

Mac Systems

Serial Deck Control Cable

Male 8-pin mini-DIN

to male 9-pin cable, for Deck Control.

Remote Deck Emulation Mode Cable

Male 8-pin

mini-DIN to female 9-pin cable, required for

Remote 9-Pin Deck Emulation.

Windows Systems

Serial Deck Control Cable

RS-232 to RS-422

cable, for serial timecode and all other

MachineControl functions.

Turnaround Adapter

9-pin adapter, used with

RS-232 to RS-422 cable, for Remote 9-Pin Deck

Emulation.

When using a supported third-party paddle

device with Pro Tools, you can use both

Serial Deck Control mode and Remote 9-Pin

Deck Emulation mode simultaneously. See

Chapter 7, “Using a Paddle Device in Local

Mode” for more information.

Do not substitute 9-pin or serial adapters for

either MachineControl cable. Each cable is

specifically wired for one operation mode.

MachineControl Guide6

Serial Deck Control Mode

Serial Deck Control mode supports bi-directional

communication between Pro Tools and a compati-

ble external machine. With this feature you can:

• Synchronize to serial timecode

• Arm tracks on the machine remotely

• Control a transport from Pro Tools

• Configure machine settings and options.

Pro Tools HDX and HD Native Systems

With Pro Tools | HD Software and

Pro Tools | HDX or Pro Tools | HD Native hard-

ware, you can use a Serial to 9-pin connection or a

9-pin to 9-pin connection for Serial Deck Control

mode.

CPU to Deck Connection

This type of connection

yields the best performance, especially with linear

decks. Use the included Serial Deck Control cable

for this type of connection.

SYNC Peripheral to Deck Connection

This type

of connection is suitable for non-linear decks. If

you are using a SYNC peripheral, as many as two

machines can be connected to the two 9-pin Out

ports on the SYNC peripheral. You can control

one machine at a time, and switch between them

from within Pro Tools. These ports support all

MachineControl modes except Remote 9-Pin Deck

Emulation mode. For Remote Deck Emulation

mode on Mac systems, a supported USB serial

adapter is required.

Remote 9-Pin Deck Emulation

Mode

This mode enables a form of deck emulation in

Pro Tools. When the Remote 9-Pin Deck Emula-

tion Mode cable is used on a supported system,

Pro Tools can respond to record-arming, transport,

and other standard 9-pin commands from an exter-

nal machine.

While in Remote 9-Pin Deck Emulation mode,

Pro Tools always generates timecode, and can be

either the timecode master or a slave device.

 On Mac systems, use the Remote 9-Pin Emula-

tion Mode cable. This mode requires a supported

serial adapter connected to a computer USB port,

and a properly wired configuration. See Chapter 6,

“Remote 9-Pin Deck Emulation Mode” for details.

 On Windows systems, Remote 9-pin Deck Em-

ulation mode uses an RS-232 to RS-422 cable and

a Turnaround adapter connected to an available se-

rial or COM port on the computer.

For computers that do not have serial ports, a

supported USB serial adapter (not provided)

is required to make the MachineControl

connection. For a list of qualified USB serial

adapters, visit www.avid.com/compatibility.

Chapter 2: Installing MachineControl 7

Connecting Machines

This section describes how to connect machines

for Serial Control Mode or Remote 9-Pin Deck

Emulation Mode.

Connecting Machines for

Serial Control Mode

For Best Serial Deck Control

For best serial deck control, connect your

deck as follows:

To connect a deck to a Mac computer:

1 Connect a supported USB serial adapter (not

provided) to a USB port on the computer.

2 Connect the provided male mini DIN-8 serial to

male 9-pin D-sub Deck Control cable to the end

of the adapter.

3 Connect the end of the cable to the machine.

To connect a deck to a Windows computer:

 Do one of the following:

• Connect the computer’s COM port to the ma-

chine, using the provided 9-pin RS-322 to

RS-422 cable.

• Use a supported USB serial adapter (not pro-

vided) for computers that do not have a 9-pin se-

rial connector to connect the machine to any

available USB port on the computer.

For Limited Serial Deck Control (Non-Linear

Decks Only)

• Connect a standard 9-pin cable from one of the

9-pin Out ports on the SYNC peripheral to the 9-

pin input of the machine. Due to performance

limitations, this configuration should be used

primarily with non-linear decks.

Connecting Machines for Remote 9-Pin

Deck Emulation Mode

To connect a machine for Remote 9-Pin Deck

Emulation mode (Mac Systems):

1 Connect a supported USB serial adapter (not

provided) to a USB port on the computer.

2 Connect the provided male mini DIN-8 serial to

female 9-pin Deck Emulation cable to the end

of the adapter.

3 Connect the end of the cable to the machine.

To connect a machine for Remote 9-Pin Deck

Emulation mode (Windows Systems):

 Connect the Turnaround adapter to the RS-322

to RS-422 cable, and connect them from an

available serial or COM port on your computer

to the 9-pin output of the machine.

Do not use the Serial port on your

Pro Tools | HDX card, HD | Native card,

HD | N ative Thunderbolt, or the 9-pin ports on the

SYNC peripheral for Remote 9-Pin Deck Emula-

tion mode. The Serial port should only be used for

SYNC peripheral connections.

MachineControl Guide8

Using a Rosetta Stone Adapter

with MachineControl

(Windows Only)

Using the Rosetta Stone adapter with Machine-

Control on Windows lets you increase reliability

for long cable runs for Serial Deck Control mode

or Remote mode.

To increase reliability in long cable runs in Remote

mode:

 Follow the instructions as described above

for setting up a Rosetta Stone converter for

an edit controller.

To increase reliability in long cable runs in Serial

Deck Control mode:

1 Connect the RS-232 cable from your com-

puter’s COM port into the RS-232 side of the

Rosetta Stone adapter.

2 Connect the RS-422 cable from the RS-422 side

of the Rosetta Stone to the deck or 9-pin patch

bay. If a longer run is needed, add more 9-pin

cable on the RS-422 end.

Authorizing MachineControl

MachineControl is automatically installed with

Pro Tools, but requires a valid MachineControl

option authorization in order to be enabled in

Pro Tools. The MachineControl feature set for

Pro Tools is automatically enabled if a valid

MachineControl authorization is detected on your

iLok.

Software is authorized using the iLok USB Smart

Key (iLok), manufactured by PACE Anti-Piracy.

An iLok can hold over 100 licenses for all of your

iLok-enabled software. Once a license for a given

piece of software is placed on an iLok, you can use

the iLok to authorize that software on any com-

puter.

A Rosetta Stone RS-232 to RS-422 adapter

(model 2/8 or 2/9) and additional RS-232 and

RS-422 cables are required.

iLok USB Smart Key

You can use either the new version of the iLok

(shown above) or the previous version of the

iLok to hold your authorizations.

An iLok USB Smart Key is not supplied with

plug-ins or software options. You can use the

iLok included with certain Pro Tools systems

or purchase one separately.

Chapter 2: Installing MachineControl 9

To authorize MachineControl:

1 If you do not have an iLok.com account, visit

www.iLok.com and sign up for an account.

• Transfer the license for your software to your

iLok.com account by doing the following:

• Visit www.avid.com/activation.

• Input your Activation Code (listed on your Acti-

vation Card) and your iLok.com User ID. Your

iLok.com User ID is the name you create for

your iLok.com account.

2 Transfer the licenses from your iLok.com

account to your iLok USB Smart Key by do-

ing the following:

• Insert the iLok into an available USB port on

your computer.

• Go to www.iLok.com and log in.

• Follow the on-screen instructions for

transferring your licenses to your iLok.

3 Launch Pro Tools.

4 If you have any unauthorized software

installed, you are prompted to authorize it.

Follow the on-screen instructions to complete

the authorization process.

Removing MachineControl

The MachineControl feature set for Pro Tools is

automatically enabled if a valid MachineControl

authorization is detected on your iLok. To disable

the MachineControl option on your system, trans-

fer your MachineControl option authorization to

another iLok (or simply remove the authorized

iLok from your system).

Starting Up Your System

To ensure that the components of your Pro Tools

system communicate properly with each other and

your external machines, start them in a particular

order.

Start up your Pro Tools system in this order:

1 For systems with an expansion chassis, turn on

the chassis.

2 Turn on any external hard drives. Wait approx-

imately ten seconds for them to come up to

speed.

3 Turn on any external machines (VTR, ATR,

synchronizer, and monitors).

4 Turn on any MIDI interfaces, MIDI devices and

synchronization peripherals.

5 Lower the volume of all output devices in your

system.

6 Turn on Pro Tools audio interfaces. Wait at

least fifteen seconds for your system hardware

to initialize.

7 Turn on your computer.

8 Launch Pro Tools.

Machine Local and Remote

Modes

Be sure to set your machine-controllable device to

“remote” or “ext” mode to receive the 9-pin infor-

mation (not “local” or front-panel mode). With

some supported machines, if all other communica-

tion is established and the machine is not in remote

mode, Pro Tools will indicate machine “local”

mode.

For more information, visit the iLok website

(www.iLok.com).

MachineControl Guide10

Chapter 3: MachineControl Communication Modes 11

Chapter 3: MachineControl Communication

Modes

MachineControl supports two machine communi-

cation modes: Serial Deck Control mode and Re-

mote 9-Pin Deck Emulation mode.

Serial Deck Control Mode

With Serial Deck Control mode, you can use the

Pro Tools Transport window to control an

external deck.

Transport

The setting of the Transport Master determines the

type of Serial Deck Control, as follows:

Transport = Pro Tools

The Transport window

controls the Pro Tools Timeline. When online, the

deck locates relative to actions taken in the

Pro Tools Timeline.

Transport = Machine

The Transport window con-

trols the machine. When Pro Tools is Online, the

Pro Tools Timeline chases the machine.

Transport = MMC

The Transport window controls

MIDI Machine Control (MMC). When Pro Tools

is Online, the Pro Tools Timeline chases MMC.

Cueing and Pre-Roll

Pro Tools Preference settings let you optimize

MachineControl operation, including adjustable

machine pre-roll, selectable edit and memory loca-

tion chasing.

Track Arming

When the Transport Master is set to Transport =

Machine, you can arm tracks of external machines

from within Pro Tools for layback and transfer.

Features include individual record enables for up

to 48 external tracks, with selectable record proto-

col and mode. Machine profiles included with the

software let you pre-configure track arming for

many machine types.

Online button, Right-click to set Transport Master

Pro Tools sessions can be as long as 24

hours. MachineControl features are dis-

abled for the final minutes of the 24-hour

period, to allow for pre-roll to be used at

the beginning of the session without un-

wanted machine shuttling.

MachineControl Guide12

Serial Timecode

When the Positional Reference is set to Serial

Timecode

in the Session Setup window, Pro Tools

can control an external machine via the Serial

Deck Control cable. This setting also enables

Pro Tools to receive timecode directly using only

the Serial Deck Control cable.

(This mode requires that the 9-pin device be capa-

ble of transmitting serial timecode. It also requires

that the Pro Tools and the device receive a com-

mon video reference.)

Using a Paddle Device in Local

Mode

When using MachineControl in Local mode with

or without an external synchronizer, you can use a

supported third-party paddle device to issue the

following Pro Tools track commands:

• Input monitoring

• Record Enable

• Record Safe

• Solo

• Solo Mute

Remote 9-Pin Deck Emulation

Mode

With Remote 9-Pin Deck Emulation mode (also

called Remote 9-Pin mode), an external synchro-

nizer can take control over Pro Tools transport and

recording functions.

Pro Tools responds to commands sent by the mas-

ter 9-pin machine controller, but because

Pro Tools is in Remote mode, many of its transport

commands are locked out.

Remote and Remote/LTC Chase

Modes

When using an external machine controller to con-

trol Pro Tools, you can configure Pro Tools to em-

ulate a 9-pin deck in either of the following modes:

Remote mode

Pro Tools emulates a device that

can be the timecode master or timecode slave.

Remote/LTC Chase mode

Pro Tools emulates a

device that receives track and transport arming

commands, while chasing incoming LTC.

Track Arming

In Remote Deck Emulation mode, you can arm

Pro Tools tracks from an external machine.

Features include remote control of individual re-

cord enables for up to 48 tracks, with selectable re-

cord protocol and mode. Included factory and user

programmable profiles let you configure track

arming for any machine type.

See Chapter 7, “Using a Paddle Device in

Local Mode.”

For arming tracks during playback, refer to

the TrackPunch and DestructivePunch fea-

ture description in the Pro Tools Reference

Guide.

Chapter 4: Setting Up Machine Control 13

Chapter 4: Setting Up Machine Control

Online and Offline Operation

Pro Tools can remotely control, or be controlled

by, any approved enabled external device. You can

select a device by using the Transport Master se-

lector in the Transport window.

To trigger Pro Tools playback or recording from

an external source, the Pro Tools Transport needs

to be online. There are four ways to put the

Pro Tools Transport online:

• Click the Online button in the Transport win-

dow.

• Choose

Options > Transport Online.

• Press Command+J (Mac) or Control+J (Win-

dows).

• Press Option+Spacebar (Mac) or Alt+Spacebar

(Windows).

The Online button in the Transport window

indicates online status. It flashes while enabled and

waiting for synchronization, and stays lit when

lock is achieved.

Transport Controls

With MachineControl, the Pro Tools Transport

window becomes a multi-function controller.

Counter Display

The Pro Tools Edit window counter displays the

current machine (9-pin) or session timecode loca-

tion, depending on which device is the Transport

Master, plus any current Session Start Time Off-

sets being applied. (See “External Timecode Off-

sets” on page 23 for more information.)

The Incoming Time display in the Session Setup

window always shows absolute incoming time-

code, without any offsets.

Transport online, Transport = Machine

(9-pin Deck Control)

Pro Tools can generate LTC while the

Transport is online, but only when Posi-

tional Reference is set to Serial Timecode.

MachineControl Guide14

Transport Master

To selecting the Transport Master:

 Right-click the Online button in the Transport

and select

Transport > Pro Tools or Transport >

Machine

.

Transport = Pro Tools

In this mode, the controls in the Transport

window are focused on Pro Tools playback and re-

cording.

When the transport is online, the machine slaves to

Pro Tools, and the session locks to the machine’s

timecode. The machine follows Preferences for

Machine Chase and Online Record.

When the transport is offline, the Pro Tools Trans-

port window controls Pro Tools only.

Transport = Machine

In this mode, the controls in the Transport window

are focused on the machine connected and enabled

for Serial Deck Control mode. Record commands

are sent to the machine only.

When the transport is online, Pro Tools slaves to

the machine. The Transport window controls the

machine, and Pro Tools chases and locks to it.

In addition, when -Spot is turned on, clips are spot-

ted to the current machine time, and the Trim tool

trims to the current machine time.

When the transport is offline, the Pro Tools Trans-

port window controls the machine only.

Toggling the Transport while

Online

When the Transport window is online, toggling the

Transport Master between Pro Tools and your ma-

chine will also toggle their master/slave relation-

ship.

Toggling the Online Status of a

Device

Use the Online pop-up menu in the Transport Mas-

ter selector to toggle the online status of a Machine

device.

To put a device online (or offline):

 Right-click the Online button in the Transport

and select (or deselect)

Online > Pro Tools or

Online > Machine.

You can also press Control+backslash (\) to

toggle between Pro Tools, the Machine,

and Remote transport (or, on a Pro Tools

control surface, press EXT TRANS).

Selecting the Transport Master

See the Pro Tools Reference Guide

for details on Auto-Spotting.

Chapter 4: Setting Up Machine Control 15

Device choices depend on the current Transport

Master and which devices have been set up in

Pro Tools.

Online Display Information

Several display elements of the Edit and Transport

windows provide machine status information

during MachineControl use, as follows:

• When Pro Tools is online, the Transport Online

button flashes. “Waiting for Sync” will be dis-

played in the status box in the lower left corner

of the Edit window.

• The Transport Online button continues to flash

until you click Play and timecode lock occurs

(all devices locked and responding in sync).

• The Timecode display in the Edit window shows

the Machine Time when the machine is Master.

• Upon lockup, the Timecode display switches to

show the session time.

• When set to 9-pin Deck mode, the Online button

icon updates to show a 9-pin icon.

Remote Mode

In Remote 9-Pin Deck Emulation mode, you put

Pro Tools in Remote mode to enable Machine

Control operation.

When you put Pro Tools in Remote mode, it re-

sponds to commands sent by the master 9-Pin ma-

chine. Many Pro Tools commands, including

transport controls, are inactive in the Transport

window.

When you take Pro Tools out of Remote mode, it

operates in Local mode and ignores commands

from the 9-pin machine controller. Pro Tools re-

sponds only to requests from the 9-pin machine

controller for machine type and status, and returns

that it is in Local mode.

To put Pro Tools in Remote mode:

1 Choose View > Transport > Synchronization.

2 Click the Remote button in the Transport

window.

For more information on Remote mode in

Pro Tools, see Chapter 6, “Remote 9-Pin Deck

Emulation Mode.”

Online menu in Transport window

The Online pop-up menu will only display de-

vices that have been properly set up in

Pro Tools.

To set up machine devices, see Chapter 5,

“Serial Deck Control Mode.”

To set up MIDI devices, see the Pro Tools

Reference Guide.

Remote button in the Transport window

MachineControl Guide16

Page is loading ...

Avid Pro Tools 11.2 User guide

Avid Pro Tools 11.2 User guide

Related papers

Other documents