V-ZUG 31029 Installation guide

31029
V-ZUG
Brand
V-ZUG
Model
31029
Type
Installation guide

This manual is also suitable for

V-ZUG 31029 is an induction glass ceramic hob with normal mounting frame, designed for use up to 2000 m above sea level. It requires a 400 V 2N~ or 230 V~ electrical connection and offers various safety features such as child lock, overheating protection, and residual heat indicators. The hob has a sleek design with touch controls and a user-friendly interface. It provides precise temperature control and quick heat-up times, making it an efficient and convenient cooking appliance.

V-ZUG 31029 is an induction glass ceramic hob with normal mounting frame, designed for use up to 2000 m above sea level. It requires a 400 V 2N~ or 230 V~ electrical connection and offers various safety features such as child lock, overheating protection, and residual heat indicators. The hob has a sleek design with touch controls and a user-friendly interface. It provides precise temperature control and quick heat-up times, making it an efficient and convenient cooking appliance.

The appliance should be installed by qualified personnel only. Each step must be carried out and checked in full in the order
specified.
Validity
These installation instructions apply to the following models: 973 (GK46TIPSC), 31029 (GK46TIMPSC)
General notes
If installing into a combustible material, the guidelines and standards for low voltage installations and fire protection must be
strictly observed.
Identification plate
The identification plate is located next to the connection
plate.
Affix the second identification plate (supplied) in an
accessible position behind the front of the fitted
cabinet beneath the appliance.
Connection plate
Identification plate
Accessories
Designation Article no.
Ventilation protective plate set for niche width 825 mm H6.1088
Ventilation protective plate set for niche width 900 mm H6.1089
Installation instructions
J973.113-4
01.05.14
Induction glass ceramic hob
With normal mounting frame
1
Electrical connection
Electrical connections must be carried out by trained electricians in accordance with the guidelines and standards for low-
voltage installations and the specifications of the local electricity supply companies.
A plug-in appliance may only be connected to a socket outlet with earthing contact, installed according to specifications. An
all-pole mains isolating device with 3 mm contact opening should be provided in the house wiring system. Switches, plug
and socket devices, circuit breakers and fusible cut-outs which are accessible after installation and which have all-poles
switching are permissible as isolating devices. Effective earthing and separately installed neutral and earth conductors
ensure safe and fault-free operation. After installation, live parts and cables with basic insulation must not be accessible.
Check old installations.
The appliance is designed for use up to a max. altitude of 2000 m above sea level.
See the identification plate for information on the necessary mains voltage, type of current and fuse protection.
The appliance is equipped with a mains cable that should be connected to a distribution box by the customer.
900
600/550
Installation pipe
Distribution box
Clamp
brown + black
blue
yellow/green
black
blue
yellow/green
brown
L2
L1
N
N
L1
PE/
PE/
400 V 2N~
230 V~
Error message U400
Incorrect connection:
Pole conductor connected to connection terminal for neutral conductor.
Quickly disconnect the appliance from the mains!
Ventilation
In order to guarantee good ventilation, a space of
at least 17.5 mm in height is necessary beneath
the appliance.
1. The back wall of the base unit in the area of
the worktop cut-out must be open to guar-
antee continuous air circulation over the
ventilation slits.
2. Alternatively, air circulation inside the cabinet
can be provided for by a concealed fresh air
intake.
In order that enough cold air can be drawn in,
there must be a continuous circulation of
fresh air that extends outside the cabinet.
≥ 15
21
Installation instructions
J973.113-4
01.05.14
Induction glass ceramic hob
With normal mounting frame
2
Installation
Indications
• The worktop must be flat.
• In order to guarantee good ventilation, a space of at least 17.5 mm in height is necessary beneath the appliance.
• A cabinet unit with a width of 900 mm is recommended for the base unit.
Fitting
The layout of the cooking zones on the hob to be built in may differ from the illustrated hob!
Y – Y
Y
Y
410
910
≥ 15
≥ 20
(30)
123
886 ±1
200
≥ 70
386 ±1
≥ 70
900
50
825
=
=
368
Cable length 1.7 m
48
from support
Aim for a
≤ of R10
Drawer/cabinet
Mounting cut-outs in side walls left/right for a niche width of 900 mm, necessary for the ventilation of the appliance.
The underside of the material between cut-outs front and rear is reinforced. The width of material between cut-outs is determined by
the producer of the stone worktop. The minimum material width can vary according to the property of the stone.
1. Create an accurate cut-out.
2. Carefully put the appliance in the installation cut-out and press against the worktop with sufficient overlap.
Installation instructions
J973.113-4
01.05.14
Induction glass ceramic hob
With normal mounting frame
3
Cool air intake if installed over a drawer or cabinet
In order to guarantee good ventilation, a space of at least 17.5 mm in height is necessary beneath the appliance.
263
(17.5)
B ≥ 65.5
B ≥ 360
(263)
A ≥ 50
48
C ≥ 15
900
825
B ≥ 65.5
103
123
A ≥ 240
C ≥ 200
(43)
(30)
3
(17.5)
Drawer
Air intake
≥ 15
for ventilation
Air discharge
Air intake
Fans
A
Necessary space below the work top for the appliance, only for niche width 825 mm.
B
Necessary space below the worktop for the ventilation of the appliance.
C
Necessary ventilation cross-section in side walls left/right. Appliances and cabinet components in the neigh-
bour niches may not cover this ventilation cross-section.
With a protective plate beneath the fan
A protective plate is recommended in the vicinity of the mains cable and to protect the ventilation openings (see ’Accessories’).
5..10 67.5
55.5
(30)
3
56
393
(19.5)
48
≤ 0.5
(2.5)
ø4
≥ 15
Achtung: mains cable
must not touch
protective plate!
C Ventilation cross-section
According to template
Drawer Fans
Installation instructions
J973.113-4
01.05.14
Induction glass ceramic hob
With normal mounting frame
4
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

V-ZUG 31029 Installation guide

31029
V-ZUG
Brand
V-ZUG
Model
31029
Type
Installation guide
This manual is also suitable for

V-ZUG 31029 is an induction glass ceramic hob with normal mounting frame, designed for use up to 2000 m above sea level. It requires a 400 V 2N~ or 230 V~ electrical connection and offers various safety features such as child lock, overheating protection, and residual heat indicators. The hob has a sleek design with touch controls and a user-friendly interface. It provides precise temperature control and quick heat-up times, making it an efficient and convenient cooking appliance.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents