V-ZUG 86A, the innovative glass ceramic hob, offers a unique cooking experience with its versatile features. Enjoy precise temperature control and even heat distribution for your culinary creations. The induction technology allows you to boil water quickly and efficiently, saving you time and energy. With its sleek, frameless design, the V-ZUG 86A seamlessly integrates into your kitchen, providing a modern and elegant touch.
V-ZUG 86A, the innovative glass ceramic hob, offers a unique cooking experience with its versatile features. Enjoy precise temperature control and even heat distribution for your culinary creations. The induction technology allows you to boil water quickly and efficiently, saving you time and energy. With its sleek, frameless design, the V-ZUG 86A seamlessly integrates into your kitchen, providing a modern and elegant touch.
Installation instructions
Glass ceramic hob, Teppan Yaki
Frameless, for flush installation
J85A.123-0
30.11.11 WIMA
1
These installation instructions apply to the model: 85A (GK16TIYSF), 86A (GK26TIYSF)
Identification plate / connection plate
Positioning: See diagram opposite
➤ Affix the second identification plate (supplied) in an accessible position behind the
front of the fitted cabinet beneath the appliance.
➤ Refer to the identification plate for specifications for the required mains voltage, current type and fuses.
➤ Application height of the appliance: up to max. 2000 m above sea level
➤ The appliance is equipped with a mains cable that should be connected to a distribution box by the customer.
The appliance should be installed by qualified personnel only. Each step must be carried out and checked in full in the order
specified.
Validity
General notes
If fitting in flammable material, the guidelines and standards for low voltage installations and for the fire protection must be
strictly observed.
This appliance is considered to be suitable for use in countries having a warm damp equable climate (WDaE). It may also be
used in other countries. If used in warm damp equable climated countries, the appliance is to be supplied through a residual
current device (RCD) having a rated residual operating current not exceeding 30 mA.
Installation accessories included
Designation Article
no.
Number
Sealing strip set H6.2695 1
Wok cover H6.2626 1
Frying spatula H6.2627 2
Accessories
Designation Article no.
Steel angle set
Installation dimension 40
Installation dimension 60
H6.2571
H6.2084
Protective plate set
For niche width 550 mm
For niche width 600 mm
H6.1082
H6.1083
Instant adhesive for installation of the steel angle
Permabond F246, incl. activator, 50 ml tube. From Silitech AG, 3008 Berne.
B11.502
Cement set
Complete with cleaning agent, primer type 1105, cartridge with silicon adhesive, black with nozzle.
Suitable for all absorbent worktop materials (wood and natural stones such as marble or granite).
86.3928.85
Special primer, type 107
Suitable for non-absorbent worktop materials (not suitable for polyethylene, polypropylene or Teflon).
45.2771.76
Electrical connections
Electrical connections must made by trained electricians in accordance with the guidelines and standards for low-voltage
installations and the specifications of the local electricity supply companies.
A plug-in appliance may only be connected to a socket outlet with earthing contact, installed according to specifications. An
all-pole mains isolating device with 3 mm contact opening should be provided in the house wiring system. Switches, plug and
socket devices, circuit breakers and fusible cut-outs which are accessible after installation and which have all-poles switching
are permissible as isolating devices. Effective earthing and separately installed neutral and earth conductors ensure safe and
fault-free operation. After installation, live parts and cables with basic insulation must not be accessible. Old installations should
always be checked.
Identification plate
Connection plate
Installation instructions
Glass ceramic hob, Teppan Yaki
Frameless, for flush installation
J85A.123-0
30.11.11 WIMA
2
Error message U400
Indications
• The worktop must be flat.
• Width of material between cut-outs for adjacent hobs in stone worktops:
The material width is determined by the producer of the stone worktop. The minimum material width of 40–60 mm can vary according
to the property of the stone, or it can be reinforced below.
Installing
1. Create the installation cut-out accurately.
– The mounting surface can be recessed by installing wood or stone bars or produced using the steel angle set (see «Accessories»).
2. Prepare the cut-out and the appliance according to the instructions in the "cementing-in" section.
3. Carefully cement the appliance in place and allow the silicon cement joints to dry for at least 24 hours.
4. Where necessary establish the mains supply connection before inserting the appliance.
Incorrect connection:
A pole conductor was connected to the connecting terminal for neutral conductors.
Quickly disconnect the appliance from the mains!
Installation
Access to the appliance from below must be guaranteed over the entire cut-out surface. For servicing, the induction
generator with the mounting plate can be removed from below. The covers to prevent accidental contact with live parts
must be removable by unscrewing.
Installation pipe
Distribution box
Clamp
600/550
min 400 for GK16TIYSF
400 V~ 2N
GK26TIYSF
PE/ green/yellow
N blue
L1 brown
L2 black
230 V~
AUS/NZ
GK16TIYSF
PE/ green/yellow
N blue
L1 brown
600/500
(30)
Z
min. 73.6
for ventilation
min. 55
600
min. 55
477
547
56.1
600/550
min.400
min. 55
600
min. 55
Z
min. 73.6
for ventilation
56.1
384
477
483
±1
min. 300
min. 300
483
±1
390
±
1
553
±1
(373/536)
(466)
R14
R0–5
8.5
0
-1
8.5
0
-0.5
8.5 ±0.5
8.5 ±0.5
GK16TIYSF
GK26TIYSF
Detail Z
Steel angle bonded or screw mounte
d
(for adhesive see «Accessories»)
Both-sided for
procedural reasons
Both-sided for
procedural reasons
Installation instructions
Glass ceramic hob, Teppan Yaki
Frameless, for flush installation
J85A.123-0
30.11.11 WIMA
3
Cool air supply if installed over a drawer or cabinet
In order to guarantee good ventilation, a space of at least 17.5 mm height is necessary beneath the appliance.
Installing the protective plate with a 3 mm ventilation gap at the front (see Accessories)
A protective plate is necessary for the adequate ventilation of the hob.
The distance between the underside of the appliance and the protective plate must be at least 17.5 mm.
Fans
min. 5
(17.5)
600/550
(30)
600/550
(30)
min. 73.6
56.1
Necessary space below
work surface for ventilation
Gk16TIYSF
Gk26TIYSF
min. 15
Air gap min. 5 mm
over entire width of
cabinet element min. 25 mm
2
Drawer
min. 400 for GK16TIYSF
min. 15
(17.5)
56.1
Caution:
Do not put mains cable
near protective plate
Well-fitting seal
over cabinet width
Air gap over entire
cabinet width min. 17 cm
2
min. 3
(30)
5..10
min. 73.6
61.6
max. 0.5
56
According to template
393
ø4
Drawer
Fan
(2.5)
Installation instructions
Glass ceramic hob, Teppan Yaki
Frameless, for flush installation
J85A.123-0
30.11.11 WIMA
4
Cement set 86.3928.85 (not supplied)
Suitable for all absorbent worktop materials (wood and natural stones such as marble, granite).
The set comprises:
For the remaining, resp. for non-absorbent worktop materials and artificial stone surfaces, the special primer type 107 *, article no.
45.2771.76 must be used. Not suitable for polyethylene, polypropylene or Teflon.
* Primer types: Firm name H. OTTO GmbH u. Co., Chemie GK, D-83413 Fridolfing
Good adhesion cannot be obtained on slate or other materials containing oil. The use of such worktop materials is not advised for the
flush installation of glass ceramic hobs.
Sealing strip set H6.2138 (supplied)
The set comprises:
Steel angle set (not supplied), see Accessories
When using the steel angle set, the cut-out and the corner radius can be cut smoothly over the entire worktop thickness, without bearing
protrusion. The correct position of the sides of the angle mounting with reference to the worktop is set with the 2 spacer gauges supplied.
Procedure
1. Thoroughly clean and degrease the cut surface of the stone.
2. Sparingly coat the bonding surface on the stone side with quick adhesive (see Accessories) (Fig. 1).
3. Thoroughly clean and degrease the bonding surface of the steel angle.
4. Apply activator to the first steel angle so that the activator and the stone surface with adhesive applied come into contact.
5. Place the two spacer gauges on the first angle mounting (Fig. 1).
6. Place the spacer gauges on the worktop surface, position the angle mounting centrally on the cut edge of the stone (Fig. 3) and
apply pressure (Fig. 2).
– The adhesive is sufficiently hardened after approx. 1 minute.
7. Remove both spacer gauges and keep them for future use.
8. Bond the other 3 angle mountings using the same procedure.
*Permabond F246 (incl. activator), 50 ml tube, article no. B11.502, from Silitech AG, 3008 Berne.
Accessories – Use
Designation Remarks Number
Cleaning agent, type T * – 1
Primer, type 1105 * 100 ml bottle 1
Silicon adhesive, black cartridge with
nozzle
1
In case of doubt as to the suitablity of cement set materials, especially when using them for the first time, we recommend that
you carry out adhesion trials on test pieces or at non-visible locations.
Article no. Characteristics Thickness × width Length per roll Number
H6.2695
Sealing strip, open-cell (soft) 5mm x 8mm 2,5 m 1
Sealing strip, highly compressed
(hard)
2mm x 8mm 0,8 m 12
The steel angles can be screw mounted with wood surfaces.
~60
~60
Fig. 2 Fig. 3Fig. 1
~40
~40
~40
~40
~40
~6
Spacer gauge
Adhesive
ActivatorAdhesive
Installation instructions
Glass ceramic hob, Teppan Yaki
Frameless, for flush installation
J85A.123-0
30.11.11 WIMA
5
1. Make sure the cut-out is clean, free of dust and any other dirt.
2. Coat 1–2× liberally with special primer (see «Accessories») (Fig. 4) and leave exposed to the air for at least 30 minutes. Wait for
the primer to completely dry.
– The surface of the cut-out will be protected by the primer against the ingress of moisture (sealed), enhancing the adhesive
properties of the adhesive.
1. Clean any grease or dirt from the edges of the hob with ethyl alcohol (fuel alcohol), isopropyl alcohol, trichlorethylene or type T
cleaning agent. Do not use water with washing-up liquid!
2. Leave to dry for a short time.
3. Stick the self-adhesive sealing strip (5 mm × 8 mm) supplied with the hob to the cleaned edge mounting surface (Fig. 5).
4. In corner areas, cement 2 «hard» sealing strip pieces each, and in centre areas 1 «hard» sealing strip piece each, over the sealing
strip.
Preparing the cut-out
Lack of care in the preliminary work can result in the ingress of liquid which will lead to the swelling of the wood and hence the
destruction of the cover.
If inappropriate pre-processing agents and adhesives are use for special cover materials, these materials may possibly show
colour changes along the cemented joint and sealing joint.
Cementing-in
Fig. 4
Apply primer
to this area
Installation instructions
Glass ceramic hob, Teppan Yaki
Frameless, for flush installation
J85A.123-0
30.11.11 WIMA
6
5. Place the hob carefully in the prepared cut-out and align it so that the sealing gap is uniform all around.
6. Press the hob, especially in the corners, so that the hob surface is level with the work surface.
7. Press the silicon adhesive into the sealing gap, avoid air bubbles and draw a somewhat raised bead.
8. Spray the silicon bead with soap solution (water and washing-up liquid).
9. Using a hard rubber or plastic spatula which has also been previously dipped into the soapy solution, spread the silicon bead so it is
flush. Regularly clean and immerse the spatula in the soapy solution.
10.Clean off all silicon residues from the glass surface and the worktop. As appropriate, the edges of the cut-out and the glass ceramic
hob plate can be covered with wide masking tape before commencing the sealing work, so that only the sealing gap is exposed.
The silicon bead can also be smoothed more finely using the thumb liberally lubricated with soap solution.
Do not press against the edge of the glass with tools!
If level compensation cannot be obtained straightaway, the length of the sealing strip pieces must be shortened
accordingly.
The silicon adhesive requires a curing time (waiting time) of at least 24 to achieve the final strength and elasticity. During this
time the hob is not to be placed in operation nor subjected to any form of mechanical stress. For this reason (impermissible
mechanical stress), the final cleaning of the hob is only to take place after the expiry of this waiting time. Cover the hob with
cardboard or similar to prevent dust and dirt from settling during the drying phase.
2
6
=
=
60
Fig. 5
Fig. 6
6
Fig. 7
1. Layer
Sealing strip «soft»
Thickness × width = 5 mm × 8 mm
2. Layer
12× Sealing strip pieces «hard»
Thickness × width = 5 mm × 8 mm x 40 mm
Sealing strip
pieces
GK16TIYSF
GK26TIYSF
-
1
-
2
-
3
-
4
-
5
-
6
V-ZUG 86A Installation guide
- Type
- Installation guide
- This manual is also suitable for
V-ZUG 86A, the innovative glass ceramic hob, offers a unique cooking experience with its versatile features. Enjoy precise temperature control and even heat distribution for your culinary creations. The induction technology allows you to boil water quickly and efficiently, saving you time and energy. With its sleek, frameless design, the V-ZUG 86A seamlessly integrates into your kitchen, providing a modern and elegant touch.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Hansgrohe AXOR XtraStoris Minimalistic Wall Niche Frameless Owner's manual
-
Whirlpool EKA 3483 IN LI Installation guide
-
Gaggenau VP 414 611 User guide
-
Typhoon 83413 Datasheet
-
LAMONA LAM1551 Operating instructions
-
Unbranded RKC0602 Owner's manual
-
ALLUSERV AIPH1 Operation & Service Manual
-
Crossco PB023-2 Operating instructions
-
Electrolux TY38TSICN User manual
-
