H3C S3100-52P Installation guide

H3C
Brand
H3C
Model
S3100-52P
Category
Network switches
Type
Installation guide

This manual is also suitable for

H3C S3600 Series Ethernet Switches
Installation Manual
Hangzhou H3C Technologies Co., Ltd.
http://www.h3c.com
Manual Version: T2-08045V-20070517-C-1.04
Copyright © 2006-2007, Hangzhou H3C Technologies Co., Ltd. and its licensors
All Rights Reserved
No part of this manual may be reproduced or transmitted in any form or by any means
without prior written consent of Hangzhou H3C Technologies Co., Ltd.
Trademarks
H3C, , Aolynk, , H
3
Care,
, TOP G, , IRF, NetPilot,
Neocean, NeoVTL, SecPro, SecPoint, SecEngine, SecPath, Comware, Secware,
Storware, NQA, VVG, V
2
G, V
n
G, PSPT, XGbus, N-Bus, TiGem, InnoVision and
HUASAN are trademarks of Hangzhou H3C Technologies Co., Ltd.
All other trademarks that may be mentioned in this manual are the property of their
respective owners.
Notice
The information in this document is subject to change without notice. Every effort has
been made in the preparation of this document to ensure accuracy of the contents, but
all statements, information, and recommendations in this document do not constitute
the warranty of any kind, express or implied.
To obtain the latest information, please access:
http://www. h3c.com
Technical Support
customer_service@h3c.com
http://www. h3c.com
About This Manual
Related Documentation
In addition to this manual, each H3C S3600 Series Ethernet Switches documentation
set includes the following:
Manual Description
H3C S3600 Series Ethernet Switches
Operation Manual-Release 1510
It guides users to use H3C S3900 Series
Ethernet Switches, in respect of CLI,
login, configuration file management,
VLAN, management VLAN, voice VLAN,
GVRP, port basic configuration, link
aggregation, MSTP, routing protocol,
DHCP, and HWPing. It also explains the
acronyms and abbreviations present in
the manual.
H3C S3600 Series Ethernet Switches
Command Manual-Release 1510
It provides detailed descriptions of the
commands available on H3C S3900
Series Ethernet Switches about CLI,
login, configuration file management,
VLAN, management VLAN, voice VLAN,
GVRP, port basic configuration, link
aggregation, MSTP, routing protocol,
DHCP, and HWPing. It also indexes the
commands presents in the manual.
Organization
H3C S3600 Series Ethernet Switches Installation Manual is organized as follows:
Chapter Contents
1 Product Overview
Introduces the characteristics and
technical specifications of S3600 Series
Ethernet Switches.
2 Preparation
Introduces the installation preparation
and precaution of S3600 Series
Ethernet Switches.
3 Installation
Introduces the procedures to install an
S3600 Series Ethernet Switch, including
the setup of the mainframe, cards and
cables.
Chapter Contents
4 Starting up the Switch at the Initial
Boot
Introduces the booting process of an
S3600 Series Ethernet Switch, including
the power-on booting of the switch and
the system initialization.
5 Loading Boot ROM and Host Software
Introduces how to load BootROM and
host software for an S3600 Series
Ethernet Switch.
6 Maintenance and Troubleshooting
Introduces the problems that might
occur during the installation and the
booting of an S3600 Series Ethernet
Switch and the related solution.
7 Appendix Lightning Protection of the
Switch
Introduces lightning protection of S3600
Series Ethernet Switches.
Conventions
The manual uses the following conventions:
I. GUI conventions
Convention Description
< >
Button names are inside angle brackets. For example, click
<OK>.
[ ]
Window names, menu items, data table and field names
are inside square brackets. For example, pop up the [New
User] window.
/
Multi-level menus are separated by forward slashes. For
example, [File/Create/Folder].
II. Symbols
Convention Description
Warning
Means reader be extremely careful. Improper operation
may cause bodily injury.
Caution
Means reader be careful. Improper operation may cause
data loss or damage to equipment.
Note Means a complementary description.
Environmental Protection
This product has been designed to comply with the requirements on environmental
protection. For the proper storage, use and disposal of this product, national laws and
regulations must be observed.
Installation Manual
H3C S3600 Series Ethernet Switches Table of Contents
i
Table of Contents
Chapter 1 Product Overview ........................................................................................................1-1
1.1 Introduction ........................................................................................................................ 1-1
1.2 S3600-28P-SI .................................................................................................................... 1-3
1.2.1 Front Panel.............................................................................................................. 1-3
1.2.2 Rear Panel .............................................................................................................. 1-7
1.3 S3600-28TP-SI .................................................................................................................. 1-8
1.3.1 Front Panel.............................................................................................................. 1-8
1.3.2 Rear Panel ............................................................................................................ 1-12
1.4 S3600-52P-SI .................................................................................................................. 1-13
1.4.1 Front Panel............................................................................................................ 1-13
1.4.2 Rear Panel ............................................................................................................ 1-14
1.5 S3600-28P-EI .................................................................................................................. 1-15
1.5.1 Front Panel............................................................................................................ 1-15
1.5.2 Rear Panel ............................................................................................................ 1-19
1.6 S3600-28F-EI................................................................................................................... 1-19
1.6.1 Front Panel............................................................................................................ 1-19
1.6.2 Rear Panel ............................................................................................................ 1-25
1.7 S3600-52P-EI .................................................................................................................. 1-26
1.7.1 Front Panel............................................................................................................ 1-26
1.7.2 Rear Panel ............................................................................................................ 1-27
1.8 S3600-28P-PWR-SI/S3600-28P-PWR-EI ....................................................................... 1-28
1.8.1 Front Panel............................................................................................................ 1-28
1.8.2 Rear Panel ............................................................................................................ 1-34
1.9 S3600-52P-PWR-SI/S3600-52P-PWR-EI ....................................................................... 1-34
1.9.1 Front Panel............................................................................................................ 1-34
1.9.2 Rear Panel ............................................................................................................ 1-36
1.10 Features of the S3600 Series ........................................................................................ 1-37
1.10.1 Features of the S3600-SI .................................................................................... 1-37
1.10.2 Features of the S3600-EI .................................................................................... 1-38
1.10.3 Features of the S3600-PWR-SI/S3600-PWR-EI................................................. 1-39
Chapter 2 Preparation...................................................................................................................2-1
2.1 Safety Precautions............................................................................................................. 2-1
2.2 Installation Site................................................................................................................... 2-1
2.2.1 Temperature/Humidity............................................................................................. 2-1
2.2.2 Cleanness ............................................................................................................... 2-2
2.2.3 Electromagnetic Susceptibility ................................................................................ 2-2
2.2.4 Laser Safety ............................................................................................................ 2-3
Installation Manual
H3C S3600 Series Ethernet Switches Table of Contents
ii
2.3 Installation Tools................................................................................................................ 2-3
Chapter 3 Installation....................................................................................................................3-1
3.1 Mounting the Switch .......................................................................................................... 3-1
3.1.1 Mounting the Switch into a 19-Inch Standard Cabinet............................................ 3-1
3.1.2 Mounting the Switch on a Desktop/Workbench .................................................... 3-10
3.2 Connecting the Power Cord and the Ground Wire.......................................................... 3-10
3.2.1 Connecting the AC Power Cord............................................................................ 3-10
3.2.2 Connecting the DC-Input Power Cord .................................................................. 3-11
3.2.3 Connecting the Ground Wire................................................................................. 3-13
3.2.4 Multi-power Input................................................................................................... 3-15
3.3 Connecting Optical Fiber ................................................................................................. 3-15
3.4 Connecting the Switch to a Console Terminal................................................................. 3-16
3.4.1 Console Cable....................................................................................................... 3-16
3.4.2 Connecting the Console Cable ............................................................................. 3-16
3.5 Connecting and Removing Special Stack Interconnect Cables ...................................... 3-17
3.5.1 Special Stack Interconnect Cables ....................................................................... 3-17
3.5.2 Connecting Special Stack Interconnect Cables .................................................... 3-17
3.5.3 Removing Special Stack Interconnect Cables ...................................................... 3-18
3.6 Verifying Installation......................................................................................................... 3-18
Chapter 4 Starting up the Switch at the Initial Boot ..................................................................4-1
4.1 Setting up a Configuration Environment............................................................................ 4-1
4.2 Connecting the Console Cable .......................................................................................... 4-1
4.3 Setting Terminal Parameters ............................................................................................. 4-1
4.4 Booting the Switch ............................................................................................................. 4-4
4.4.1 Verifying Installation before Power-up .................................................................... 4-4
4.4.2 Powering up the Switch........................................................................................... 4-4
Chapter 5 Loading Boot ROM and Host Software .....................................................................5-1
5.1 Introduction to Loading Approaches.................................................................................. 5-1
5.2 File attribute in Boot ROM ................................................................................................. 5-1
5.2.1 Introduction to File Attribute .................................................................................... 5-1
5.2.2 Impact of File Attributes on Downloading and Booting ........................................... 5-2
5.2.3 Setting the Attribute of a File................................................................................... 5-3
5.3 Loading Software Locally................................................................................................... 5-5
5.3.1 Boot Menu ............................................................................................................... 5-5
5.3.2 Loading Software from Console Port Using XModem ............................................ 5-6
5.3.3 Loading Software from an Ethernet Port Using TFTP .......................................... 5-11
5.3.4 Loading Software from an Ethernet Port Using FTP............................................. 5-12
5.4 Loading Software Remotely............................................................................................. 5-13
5.4.1 Loading Software Remotely Using FTP................................................................ 5-14
5.4.2 Loading Software Remotely Using TFTP.............................................................. 5-15
Installation Manual
H3C S3600 Series Ethernet Switches Table of Contents
iii
Chapter 6 Maintenance and Troubleshooting............................................................................6-1
6.1 Dealing with Loading Failures............................................................................................ 6-1
6.2 Dealing with Password Loss.............................................................................................. 6-1
6.2.1 Dealing with User Password Loss........................................................................... 6-1
6.2.2 Recovering the Boot ROM Password ..................................................................... 6-2
6.3 Dealing with Power System Failures ................................................................................. 6-2
6.4 Dealing with Configuration System Failures...................................................................... 6-2
Installation Manual
H3C S3600 Series Ethernet Switches Chapter 1 Product Overview
1-1
Chapter 1 Product Overview
1.1 Introduction
H3C S3600 Series Ethernet Switches developed by H3C are high-performance,
high-density, easy-to-install, NMS-manageable intelligent Ethernet switches which
support wire-speed Layer 2/3 switching.
Table 1-1 lists the models of H3C S3600 Series Ethernet Switches.
Table 1-1 Models of the S3600 series
Subseries Model
Power
supply
Number
of
service
ports
Number of
100 Mbps
ports
Number
of 1000
Mbps
uplink
ports
Number
of
Console
ports
S3600-2
8P-SI
AC 28
24 ×
10Base-T/
100Base-T
X Ethernet
ports
4 ×
1000Bas
e-X SFP
ports
1
S3600-2
8TP-SI
AC 28
24 ×
10Base-T/
100Base-T
X Ethernet
ports
2 ×
1000Bas
e-X SFP
ports, 2 ×
10/100/1
000Base-
T
Ethernet
ports
1
H3C
S3600-SI
S3600-5
2P-SI
AC 52
48 ×
10Base-T/
100Base-T
X Ethernet
ports
4 ×
1000Bas
e-X SFP
ports
1
S3600-2
8P-PW
R-SI
AC/DC 28
24 ×
10Base-T/
100Base-T
X Ethernet
ports
4 ×
1000Bas
e-X SFP
ports
1
H3C
S3600-PW
R-SI
S3600-5
2P-PW
R-SI
AC/DC 52
48 ×
10Base-T/
100Base-T
X Ethernet
ports
4 ×
1000Bas
e-X SFP
ports
1
Installation Manual
H3C S3600 Series Ethernet Switches Chapter 1 Product Overview
1-2
Subseries Model
Power
supply
Number
of
service
ports
Number of
100 Mbps
ports
Number
of 1000
Mbps
uplink
ports
Number
of
Console
ports
S3600-2
8P-EI
AC/DC 28
24 ×
10Base-T/
100Base-T
X Ethernet
ports
4 ×
1000Bas
e-X SFP
ports
1
S3600-2
8F-EI
AC/DC 28
24 x
100Base-X
SFP ports
2 ×
1000Bas
e-X SFP
ports, 2 ×
10/100/1
000Base-
T
Ethernet
ports
1
H3C
S3600-EI
S3600-5
2P-EI
AC/DC 52
48 ×
10Base-T/
100Base-T
X Ethernet
ports
4 ×
1000Bas
e-X SFP
ports
1
S3600-2
8P-PW
R-EI
AC/DC 28
24 ×
10Base-T/
100Base-T
X Ethernet
ports
4 ×
1000Bas
e-X SFP
ports
1
H3C
S3600-PW
R-EI
S3600-5
2P-PW
R-EI
AC/DC 52
48 ×
10Base-T/
100Base-T
X Ethernet
ports
4 ×
1000Bas
e-X SFP
ports
1
Note:
z The S3600-28P-PWR-SI, S3600-28P-PWR-EI, S3600-52P-PWR-SI, and
S3600-52P-PWR-EI provides over-temperature protection mechanism. When the
internal temperature exceeds 65°C (149°F), they will stop providing power from all
ports. When the temperature is below 60°C (140°F), they will continue to provide
power from all ports.
z Only the recommended PoE power supply can be used for the S3600-28P-PWR-SI,
S3600-28P-PWR-EI, S3600-52P-PWR-SI, and S3600-52P-PWR-EI. The –48 VDC
from the equipment room cannot be used directly. Otherwise, devices may be
damaged.
Installation Manual
H3C S3600 Series Ethernet Switches Chapter 1 Product Overview
1-3
1.2 S3600-28P-SI
1.2.1 Front Panel
I. Schematic diagram
The S3600-28P-SI provides twenty-four 10Base-T/100Base-TX auto-sensing Ethernet
ports, four 1000Base-X SFP ports, and one Console port on the front panel, as shown
in
Figure 1-1.
(1) 10Base-T/100Base-TX auto-sensing Ethernet port status LEDs
(2) 1000Base-X SFP port status LEDs (3) AC power LED
(4) Mode LED (5) Mode button
(6) 7-segment digital LED (7) Console port
Figure 1-1 Front panel of the S3600-28P-SI
II. LEDs
The S3600-28P-SI provides one AC power LED, one mode LED, one 7-segment digital
LED, twenty-four 10Base-T/100Base-TX auto-sensing Ethernet port status LEDs, and
four 1000Base-X SFP port status LEDs on the front panel. You can learn how the
switch operates by observing the LEDs listed in
Table 1-2.
Table 1-2 LEDs on the front panel of the S3600-28P-SI
LED Mark Status Indication
Speed Solid green
Rate information of
10Base-T/100Base-TX
auto-sensing Ethernet ports, and
1000Base-X SFP ports
Mode
LED
Mode
Duplex Solid yellow
Duplex information of
10Base-T/100Base-TX
auto-sensing Ethernet ports, and
1000Base-X SFP ports
Installation Manual
H3C S3600 Series Ethernet Switches Chapter 1 Product Overview
1-4
LED Mark Status Indication
Solid green The switch is started normally.
Flashing green (1 Hz)
The system is running a power-on
self-test (POST) or downloading
software.
Solid red
The system fails a POST or a fault
occurs.
Flashing yellow (1 Hz)
Some ports fail a POST or
malfunctions occur.
AC
Power
LED
PWR
OFF The power is disconnected.
ON A 100 Mbps link is present.
Green
Flashi
ng
Data is being received/sent on
the port.
ON A 10 Mbps link is present.
Yellow
Flashi
ng
Data is being received/sent on
the port.
Flashing yellow
(3 Hz)
The port fails the POST.
Speed
OFF No link is present.
ON
The port is operating in full duplex
mode.
Green
Flashi
ng
Data is being received/sent on
the port.
ON
The port is operating in half
duplex mode.
Yellow
Flashi
ng
Data is being received/sent on
the port.
Flashing yellow
(3 Hz)
The port fails the POST.
10Base
-T/100
Base
-TX
port
status
LED
—
Duplex
OFF
No data is being received/sent on
the port.
Installation Manual
H3C S3600 Series Ethernet Switches Chapter 1 Product Overview
1-5
LED Mark Status Indication
ON A 1000 Mbps link is present.
Green
Flash
Data is being received/sent on
the port.
Flashing yellow
(3 Hz)
The port fails POST.
Speed
OFF No link is present.
ON
The port is operating in full duplex
mode.
Green
Flash
Data is being received/sent on
the port.
Flashing yellow
(3 Hz)
The port fails the POST.
Duplex
OFF The port is not connected.
Flashing green
(3 Hz)
The port fails the POST.
1000
Base-S
FP port
status
LED
—
PoE
mode
OFF ––
ON
The port is connected, and the
device is in an IRF loop fabric.
Green
Flashi
ng
Data is being received/sent on
the port.
ON
The port is connected, and the
device is in an IRF chain fabric.
Yellow
Flash
Data is being received/sent on
the port.
Flashing green
(3Hz)
A fault occurs to Fabric.
Flashing yellow
(3 Hz)
The port fails the POST.
Speed
OFF The port is not connected.
ON The port is in full duplex mode.
Green
Flashi
ng
Data is being received/sent on
the port.
Flashing yellow
(3 Hz)
The port fails the POST.
Duplex
OFF The port is not connected.
Flashing yellow
(3 Hz)
The port fails the POST.
Status
LED of
the
1000B
ase-X
SFP
port
serving
as a
fabric
port
—
PoE
OFF ––
Installation Manual
H3C S3600 Series Ethernet Switches Chapter 1 Product Overview
1-6
LED Mark Status Indication
POST
running
The PWR LED
flashes green
Displays the POST test ID (in the
range of 1 to 9).
The PWR LED
flashes yellow
POST
failed
The PWR LED
is solid red
Flashes the POST test ID of the
failed test.
Software
downloa
ding
The PWR LED
flashes green
A bar rotates clockwise around
the LED.
Fan
failed
The PWR LED
is solid red
Displays “F”.
7-segm
ent
digital
LED
Unit
Unit ID Button released
Displays the unit ID in the fabric;
and displays “1” if there is only
one unit.
III. Attributes of the 10Base-T/100Base-TX Ethernet ports
Table 1-3 Attributes of the 10Base-T/100Base-TX Ethernet Ports on the S3600-28P-SI
Attribute Description
Connector RJ-45
Number of ports 24
Rate
z 10 Mbps, half duplex/full duplex
z 100 Mbps, half-duplex/full duplex
z MDI/MDI-X auto-sensing
Standard IEEE 802.3u
Transmission distance
over the selected medium
100 m (328.08 ft) over the category-5 unshielded
twisted pair (UTP) cable
IV. Console port
The S3600-28P-SI provides one EIA/TIA-232 compliant Console port for local or
remote configuration.
Table 1-4 lists the attributes of the Console port.
Table 1-4 Console port attributes
Attribute Description
Connector RJ-45
Standard Asynchronous EIA/TIA-232
Baud rate 9600 bps (default)
Installation Manual
H3C S3600 Series Ethernet Switches Chapter 1 Product Overview
1-7
Attribute Description
Service
z Connection to the ASCII terminal
z Connection to the serial interface of a local terminal (a PC for
example) or to a remote terminal through a pair of modems), where
terminal emulation program is run
V. Attributes of the 1000Base-X SFP ports
The S3600-28P-SI provides four 1000Base-X SFP ports (numbered from 25 to 28) on
its front panel.
SFP modules allow for great flexibility because they are hot swappable and user
configurable.
Table 1-5 lists the available SFP modules.
Table 1-5 1000Base-X SFP modules
Type Model
SFP-GE-SX-MM850-A
SFP-GE-LX-SM1310-A
SFP-GE-LH40-SM1310
SFP-GE-LH40-SM1550
1000Base-X SFP
module
SFP-GE-LH70-SM1550
SFP optical
module
SFP electrical
interface module
SFP-GE-T
Note:
z The types of 1000Base-X SFP modules may be subject to changes without notice.
Consult H3C marketing personnel or technical support personnel to obtain the latest
information about SFP modules.
z For specifications of SFP modules, refer to H3C Low End Series Ethernet Switches
Pluggable Modules Manual.
1.2.2 Rear Panel
I. Schematic diagram
The S3600-28P-SI provides an AC power socket and a grounding screw on its rear
panel, as shown in
Figure 1-2.
Installation Manual
H3C S3600 Series Ethernet Switches Chapter 1 Product Overview
1-8
（1）（2）（1）（2）
(1) AC power socket (2) Grounding screw
Figure 1-2 Rear panel of the S3600-28P-SI
II. Power system
The following gives the input voltage specifications for the S3600-28P-SI:
Rated voltage range: 100 VAC to 240 VAC, 50/60 Hz
Input voltage range: 90 VAC to 264 VAC, 47 to 63 Hz
1.3 S3600-28TP-SI
1.3.1 Front Panel
I. Schematic diagram
The S3600-28TP-SI provides twenty-four 10Base-T/100Base-TX auto-sensing
Ethernet ports, two 1000Base-X SFP ports, two 10/100/1000Base-T auto-sensing
Ethernet ports, and one Console port on the front panel, as shown in
Figure 1-3.
(1) 10Base-T/100Base-TX auto-sensing Ethernet port status LEDs
(2) 1000Base-X SFP port status LEDs
(3) 10/100/1000Base-T auto-sensing Ethernet port status LEDs
(4) Console port
(5) 7-segment digital LED (6) AC power LED
(7) Mode LED (8) Mode button
Figure 1-3 Front panel of the S3600-28TP-SI
II. LEDs
The S3600-28TP-SI provides one power LED, one DC power LED, one mode LED,
one 7-segment digital LED, twenty-four 10Base-T/100Base-TX Ethernet port status
Installation Manual
H3C S3600 Series Ethernet Switches Chapter 1 Product Overview
1-9
LEDs, two 1000Base-X SFP port status LEDs, and two 10/100/1000Base-T
auto-sensing Ethernet port status LEDs. You can learn how the switch operates by
observing the LEDs listed in
Table 1-6.
Table 1-6 LEDs on the front panel of the S3600-28TP-SI
LED Mark Status Indication
Solid green The switch is started normally.
Flashing green (1Hz)
The system is running a POST or
downloading software.
Solid red
The system fails the POST or a
fault occurs.
Flashing yellow (1Hz)
Some ports fail a POST or
malfunctions occur.
AC
power
LED
PWR
OFF The power is disconnected.
Speed Solid green
Rate information of
10Base-T/100Base-TX Ethernet
ports, and 1000Base-X SFP ports.
Mode
LED
Mode
Duplex Solid yellow
Duplex information of
10Base-T/100Base-TX Ethernet
ports, and 1000Base-X SFP ports.
ON A 100 Mbps link is present.
Gree
n
Flas
hing
Data is being received/sent on the
port.
On A 10 Mbps link is present.
Yello
w
Flas
hing
Data is being received/sent on the
port.
Flashing
yellow (3Hz)
The port fails a POST.
Speed
OFF No link is present.
ON
The port is operating in full duplex
mode.
Gree
n
Flas
hing
Data is being received/sent on the
port.
ON
The port is operating in half duplex
mode.
Yello
w
Flas
hing
Data is being received/sent on the
port.
Flashing
yellow (3Hz)
The port fails a POST.
10Base-
T/100Ba
se-TX
port
status
LED
—
Duplex
OFF
No data is being received/sent on
the port.
Installation Manual
H3C S3600 Series Ethernet Switches Chapter 1 Product Overview
1-10
LED Mark Status Indication
ON A 1000 Mbps link is present.
Gree
n
Flas
hing
Data is being received/sent on the
port.
Flashing
yellow (3Hz)
The port fails a POST.
Speed
OFF No link is present.
ON
The port is operating in full duplex
mode.
Gree
n
Flas
hing
Data is being received/sent on the
port.
Flashing
yellow (3Hz)
The port fails a POST.
Duplex
OFF No link is present.
Flashing
green (3Hz)
The port fails a POST.
1000Bas
e-X SFP
port
status
LED
—
PoE
OFF —
ON A 1000 Mbps link is present.
Gree
n
Flas
hing
Data is being received/sent on the
port.
ON A 10/100 Mbps link is present.
Yello
w
Flas
hing
Data is being received/sent on the
port.
Flashing
yellow
(3Hz)
The port fails a POST.
Speed
OFF No link is present.
ON
The port is operating in full duplex
mode.
Gree
n
Flas
hing
Data is being received/sent on the
port.
ON
The port is operating in half duplex
mode.
Yello
w
Flas
hing
Data is being received/sent on the
port
Flashing
yellow (3Hz)
The port fails POST.
10/100/
1000Bas
e-T
Ethernet
port
status
LED
—
Duplex
OFF
No data is being received/sent on
the port.
Installation Manual
H3C S3600 Series Ethernet Switches Chapter 1 Product Overview
1-11
LED Mark Status Indication
POST
running
The PWR
LED flashes
green
Displays the POST test ID (in the
range of 1 to 9).
The PWR
LED flashes
yellow
POST
failed
The PWR
LED is solid
red
Flashes the POST test ID of the
failed test.
Softwar
e
loading
The PWR
LED flashes
green
A bar rotates clockwise around the
LED.
Fan
failure
The PWR
LED is solid
red
Displays “F”.
7-segme
nt digital
LED
Unit
Unit ID
Button
released
Displays the unit ID in the fabric,
and displays “1” if there is only one
unit.
III. Attributes of the 10Base-T/100Base-TX Ethernet ports
The S3600-28TP-SI provides twenty-four 10Base-T/100Base-TX Ethernet ports
(numbered from 1 to 24) on the front panel. For attributes of these ports, see
Table 1-3.
IV. Attributes of the 1000Base-X SFP ports
The S3600-28TP-SI provides two 1000Base-X SFP ports numbered 25 and 26 on the
front panel.
SFP modules allow for great flexibility because they are hot swappable and user
configurable.
Table 1-5 lists the available SFP modules.
Note:
z The types of 1000Base-X SFP modules may be subject to changes without notice.
Consult H3C marketing personnel or technical support personnel to obtain the latest
information about SFP modules.
z For specifications of SFP modules, refer to H3C Low End Series Ethernet Switches
Pluggable Modules Manual.
Installation Manual
H3C S3600 Series Ethernet Switches Chapter 1 Product Overview
1-12
V. Attributes of the 10/100/1000Base-T Ethernet ports
The S3600-28TP-SI can provide two 10/100/1000Base-T Ethernet ports numbered 27
and 28 on the front panel. For attributes of these two ports, see
Table 1-7.
Table 1-7 Attributes of the 10/100/1000Base-T Ethernet ports on the S3600-28TP-SI
Attribute Description
Connector RJ-45
Number of ports 2
Rate
z 10/100 Mbps, half duplex/full duplex
z 1000 Mbps, full duplex
z MDI/MDI-X auto-sensing
Standard
z IEEE 802.3u
z IEEE 802.3ab
Transmission distance
over the selected medium
100 m (328.08 ft) over the category-5 unshielded
twisted pair (UTP) cable
VI. Console port
The S3600-28TP-SI provides one EIA/TIA-232 compliant Console port for local or
remote switch configuration. For the attributes, see
Table 1-4.
1.3.2 Rear Panel
I. Schematic diagram
The S3600-28TP-SI provides an AC power socket and a grounding screw on the rear
panel, as shown in
Figure 1-4.
（1）（2）（1）（2）
(1) AC power socket (2) Grounding screw
Figure 1-4 Rear panel of the S3600-28TP-SI
II. Power system
The following gives the input voltage specifications for the S3600-28TP-SI:
Rated voltage range: 100 VAC to 240 VAC, 50/60 Hz
Input voltage range: 90 VAC to 264 VAC, 47 to 63 Hz
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98

H3C S3100-52P Installation guide

H3C
Brand
H3C
Model
S3100-52P
Category
Network switches
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents