VADDIO AutoTrak 2.0 Installation and User Manual

Category
Camera accessories
Type
Installation and User Manual
©2014 Vaddio - All Rights Reserved. AutoTrak 2.0 with Optional EasyTalk Wireless Audio Interface - Document 342-0382 Rev. E
Vaddio™ AutoTrak™ 2.0
Camera Tracking System featuring Automatic Pan/Tilt/Zoom
Camera Tracking
Part Numbers:
AutoTrak 2.0
Camera Tracking System: North America
999-7250-000
: AutoTrak 2.0-Dual HD-18 Kit with
Quick-Connect DVI/HDMI Interface-North America
999-7260-000
: AutoTrak 2.0-HD-18 & HD-20 Kit with
Quick-Connect DVI/HDMI Interface-North America
AutoTrak 2.0
Camera Tracking System: International
999-7250-001
: AutoTrak 2.0-Dual HD-18 Kit with
Quick-Connect DVI/HDMI Interface-International
999-7260-001
: AutoTrak 2.0-HD-18 & HD-20 Kit with
Quick-Connect DVI/HDMI Interface-International
Optional:
EasyTalk AutoTrak 2.0 Wireless Audio Interface:
998-7230-000: EasyTalk AutoTrak 2.0 Wireless Audio Interface - North America
998-7230-001: EasyTalk AutoTrak 2.0 Wireless Audio Interface - International
I
NSTALLATION AND
U
SERS
G
UIDE
AutoTrak 2.0 Camera Tracking System
AutoTrak 2.0 Camera Tracking System - Document Number 342-0382 Rev. E Page 2 of 52
Inside Front Cover - Blank
Inside Front Cover - Blank
AutoTrak 2.0 Camera Tracking System
AutoTrak 2.0 Camera Tracking System - Document Number 342-0382 Rev. E Page 3 of 52
AutoTrak 2.0 System Overview
The AutoTrak 2.0 System is an IR tracking system that consists of an IR
lanyard attached to a rechargeable Lithium Ion Belt Pack that is worn by a
presenter or instructor. Within the lanyard’s cloth cover, there are fifteen
(15) 850nm wavelength IR LEDs on a flat flex circuit that emit IR light that
is tracked by a HD-18 PTZ IR Reference Camera with special IR filters.
The IR position is relayed to the AutoTrak 2.0 CPU which in turn controls
the HD-18 PTZ (or the HD-20 PTZ) Tracking Camera which follows the
presenter and keeps the presenter framed in the camera shot throughout
the presentation environment.
The AutoTrak 2.0 System is designed to integrate with the optional
EasyTalk AutoTrak 2.0 Wireless Audio System. The EasyTalk AutoTrak
2.0 Wireless Audio System includes a HD wireless receiver that receives
the HD wireless microphone audio transmitted from the AutoTrak 2.0 IR
Lanyard and Belt Pack. It also provides audio outputs for connection to
an audio amplifier/speaker system or a video conference system. It
includes a USB output that can directly connect to a PC USB port which
will provide connection of the microphone and room speaker audio for use
with Unified Communication clients such as Skype, Microsoft Lync,
Google+ and others.
There are two versions of AutoTrak 2.0:
AutoTrak 2.0 Dual HD-18
999-7250-000 North America
999-7250-001 International
Includes: One (1) HD-18 PTZ IR Reference Camera and one (1)
HD-18 Tracking Camera
AutoTrak 2.0 HD-18/HD-20
999-7260-000 North America
999-7260-001 International
Includes: One (1) HD-18 PTZ IR Reference Camera and one (1)
HD-20 PTZ Tracking Camera
The HD-18 and HD-20 cameras use the Vaddio Quick-Connect DVI/HDMI Interface to provide Cat-5e
cabling systems for ease of set up and installation. The system can be permanently installed or
configured as a cart system for portability and ease of positioning in the largest of lecture halls. Each
system includes a dual camera mount which can be wall mounted or mounted on top of the Vaddio Edge
series video carts.
The optimum operating range or the system (from the IR Lanyard to the IR Reference camera) is between
12’ (3.65m) and up to 40’ (12.2m). System positioning is critical for proper and consistent operation.
The AutoTrak 2.0 can be installed as a standalone system or can be used in conjunction with myriad
Vaddio Presenter controlled solutions including AutoPresenter™, PresenterPOD™, ControlVIEW XHD™,
TouchVIEW™, AutoVIEW™ IR, StepVIEW™ Mats, and MicVIEW™. As an added benefit, once the
AutoTrak 2.0 system is configured the Mouse, Keyboard and Monitor I/O devices can be removed from
the system to ensure the system isn’t subject to unauthorized modification.
The AutoTrak’s camera tracking has been improved and the new SmoothTrak™, AutoTilt™ and
SmoothTilt™ functions have been implemented. AutoTilt works to keep the presenter centrally framed in
the shot as they move side to side and now closer and further away from the camera too. SmoothTrak
provides for a much more natural set of camera movements as the presenter moves around the room.
SmoothTilt allows the camera to follow the presenter in multiple directions for concurrent pan and tilting of
the camera, which more closely resembles a professional production.
AutoTrak 2.0, 999-7250-000
Dual HD-18 PTZ Cameras
AutoTrak 2.0, 999-7260-000
HD-18 PTZ IR Reference and
HD-20 PTZ Tracking Camera
AutoTrak 2.0 Camera Tracking System
AutoTrak 2.0 Camera Tracking System - Document Number 342-0382 Rev. E Page 4 of 52
Intended Use:
Before operating the device, please read the entire manual thoroughly. The system was designed, built and tested for
use indoors, and with the provided power supply and cabling. The use of a power supply other than the one provided
or outdoor operation has not been tested and could damage the device and/or create a potentially unsafe operating
condition.
Important Safeguards:
Read and understand all instructions before using. Do not operate any device if it has been dropped or damaged. In
this case, a Vaddio technician must examine the product before operating. To reduce the risk of electric shock, do
not immerse in water or other liquids and avoid extremely humid conditions.
Save These Instructions:
The information contained in this manual will help you install and operate your product. If these instructions are
misplaced, Vaddio keeps copies of Specifications, Installation and User Guides and most pertinent product drawings
for the Vaddio product line on the Vaddio website. These documents can be downloaded from www.vaddio.com free.
UNPACKING:
Carefully remove all of the parts for the AutoTrak 2.0 999-7250-000 Dual HD-18 Kit with Quick Connect DVI/HDMI Interface (North
America Only) packaging:
One (1) AutoTrak 2.0 CPU (closed system preloaded with AutoTrak 2.0 software and video card)
One (1) AC Cord Set for AutoTrak 2.0 CPU
One (1) PS/2 Keyboard and PS/2 Mouse
One (1) IR and Audio Lanyard with attached cable with 5-pin mini XLR connector,
One (1) Audio-Technica AT8439 Cable Clip to attach Lanyard Central Medallion to clothing
One (1) Triple Circle Magnet Kit for attaching the Lanyard Central Medallion to clothing from the inside
One (1) Belt Pack Unit “BPU” with 1” (1/4 wave) RP-SMA straight antenna and attached belt clip with rechargeable lithium-ion
battery pack and 5 VDC USB charging power supply for North America
One (1) USB Type A-Male to micro-B-Male Charging Cable
One (1) Vaddio PowerRite 12 VDC, 1A Switching Power Supply with North American Power Cord
One (1) AutoTrak POD Kit (for presets and rescan) and Manual (in separate box)
AutoTrak 2.0-Dual HD-18 Kit:
One (1) *HD-18 PTZ Camera with AutoTrak 2.0 Software preloaded - Tracking Camera
One (1) Quick-Connect DVI/HDMI SR Interface (998-1105-018) for Tracking Camera
One (1) 24VDC, 2A, Switching Power Supply with North American Power Cord
One (1) *HD-18 PTZ Camera with AutoTrak 2.0 Software preloaded – IR Reference Camera
One (1) 37mm female lens ring adapter, One (1) 37mm to 58mm adapter ring, One (1) 58mm polarizing filter, One (1) 58mm
band-pass IR filter, all parts adapters and filters attached to HD-18 Camera
One (1) AutoTrak 2.0 Quick-Connect Box (998-1105-020)
One (1) Standard Quick-Connect Box (998-1105-001)
One (1) 24VDC, 2A, Switching Power Supply with North American Power Cord
One (1) 18”/45.8cm Video Cable (BNC to RCA)
One (1) 12”/30.48cm Cat 5e Patch Cable
One (1) 998-2100-000 - Vaddio IR Remote & Manual (2-AAA batteries not included)
One (1) **535-2000-233 Stacked Dual Mount for two cameras and Mounting Hardware
Three (3) 998-1001-232 Control Adapters
One (1) 998-7200-232 Control Adapter for use with the AutoPresenter - (Only needed when used with the AutoPresenter for
Tracking Camera PTZ Presets)
One (1) AutoTrak Pod Kit 998-7200-110 (for presets and rescan) and Manual (in separate box)
Documentation and Manuals (Document Number (342-0382)
For the 999-7260-000 System¨ Start with the 999-7250-000 System
Remove: One (1) *AutoTrak HD-18 PTZ Camera with AutoTrak 2.0 Software preloaded - Tracking Camera
Add: One (1) *AutoTrak HD-20 PTZ Camera with AutoTrak 2.0 Software preloaded - Tracking Camera
Use only the power supply provided with the system. Use of any unauthorized power
supply will void any and all warranties.
Please do not use “pass-thru” type RJ-45 connectors. These pass-thru type connectors do not
work well for professional installations and can be the cause of intermittent connections which
can result in the RS-232 control line failing and locking up, and/or compromising the HSDS™
signals. For best results please use standard RJ-45 connectors and test all cables for proper
p
in-outs
p
rior to use and connection to Vaddio
p
roduct.
The AutoTrak 2.0 CPU is a computer running a Linux OS. Please do not
remove power from the AutoTrak 2.0 CPU without first shutting the system
down, as you would any other business computer. Only after the AutoTrak
2.0 CPU has been shut down, it is safe to remove power. Consistently power
cycling the CPU with the Rear Power Switch may cause the system to load
improperly, which could potentially result in data errors requiring factory
service.
Please treat the AutoTrak 2.0
CPU like a computer.
Please shut down
the CPU before
removing power,
like all business
computers, or…
AutoTrak 2.0 Camera Tracking System
AutoTrak 2.0 Camera Tracking System - Document Number 342-0382 Rev. E Page 5 of 52
UNPACKING:
Carefully remove all of the parts for the AutoTrak 2.0 999-7250-001 (Int’l) Dual HD-18 Kit with Quick
Connect DVI/HDMI Interface) packaging:
One (1) AutoTrak 2.0 CPU (closed system preloaded with AutoTrak 2.0 software and video card)
One (1) Euro Power Cord for AutoTrak 2.0 CPU
One (1) UK Power Cord for AutoTrak 2.0 CPU
One (1) PS/2 Keyboard and PS/2 Mouse
One (1) IR and Audio Lanyard with attached cable with 5-pin mini XLR connector
One (1) Audio-Technica AT8439 Cable Clip to attach Lanyard Central Medallion to clothing
One (1) Triple Circle Magnet Kit for attaching the Lanyard Central Medallion to clothing
One (1) Belt Pack Unit “BPU” with 1” (1/4 wave) RP-SMA straight antenna and attached belt clip with
rechargeable lithium ion battery pack
One (1) 5 VDC USB Charging Supply for Europe
One (1) 5 VDC USB Charging Supply for UK
One (1) USB Type A-Male to micro-B-Male Charging Cable
One (1) Vaddio PowerRite 12 VDC, 1A Switching Power Supply
One (1) Euro Power Cord
One (1) UK Power Cord
One (1) AutoTrak POD Kit (for presets and rescan) and Manual (in separate box)
AutoTrak 2.0-Dual HD-18 Kit:
One (1) *HD-18 PTZ Camera with AutoTrak 2.0 Software preloaded - Tracking Camera
One (1) Quick-Connect SR Interface (998-1105-016) for Tracking Camera
One (1) 24VDC, 2A, Switching Power Supply
One (1) Euro Power Cord
One (1) UK Power Cord
One (1) *HD-18 PTZ Camera with AutoTrak 2.0 Software preloaded - IR Reference Camera
One (1) 37mm female lens ring adapter, One (1) 37mm to 58mm adapter ring, One (1) 58mm
polarizing filter, One (1) 58mm band-pass IR filter, all parts adapters and filters attached to HD-18
Camera
One (1) AutoTrak 2.0 Quick-Connect Box (998-1105-020)
One (1) Standard Quick-Connect Box (998-1105-001)
One (1) 24VDC, 2A, 50/60Hz 110-240V Switching Power Supply (451-2000-0024)
One (1) Euro Power Cord
One (1) UK Power Cord
One (1) 18”/45.8cm Video Cable (BNC to RCA)
One (1) 12”/30.48cm Cat 5e Patch Cable
One (1) 998-2100-000 - Vaddio IR Remote & Manual (2-AAA batteries not included)
One (1) **535-2000-233 Stacked Dual Mount for two (2) cameras and Mounting Hardware
Three (3) 998-1001-232 Control Adapters
One (1) 998-7200-232 Control Adapter for use with the AutoPresenter - (Only needed when used with
the AutoPresenter for Tracking Camera PTZ Presets)
One (1) AutoTrak Pod 998-7200-110 (for presets and rescan) and Manual (in separate box)
Documentation and Manuals (Document Number (342-0382)
For the 999-7260-001 System - Start with the 999-7250-001 System
Remove: One (1) *HD-18 PTZ Camera with AutoTrak 2.0 Software preloaded - Tracking Camera
Add: One (1) *HD-20 PTZ Camera with AutoTrak 2.0 Software preloaded - Tracking Camera
*Note 1: The Vaddio HD-18 and HD-20 cameras are preloaded with AutoTrak 2.0 control protocols which
differ from the modified VISCA type control codes normally used in the stock HD-18 PTZ Camera. The
HD-18 and HD-20 cameras will work with the Vaddio IR Remote but is recommended that the PTZ
positions of the camera be set with the AutoTrak 2.0 Software. The HD-18 and HD-20 AutoTrak 2.0
cameras will not work with any other controller other than AutoTrak 2.0 at this time.
**Note 2: The stacked camera arrangement is required for the AutoTrak 2.0 software to track properly.
AutoTrak 2.0 Camera Tracking System
AutoTrak 2.0 Camera Tracking System - Document Number 342-0382 Rev. E Page 6 of 52
AutoTrak 2.0 Components:
AutoTrak 2.0 CPU
The AutoTrak 2.0 CPU is a 1-RU rack mount computer that will come preloaded with the AutoTrak 2.0
software. The exact specifications are subject to change and any changes that will be made will be in the
spirit of product improvement only. The AutoTrak 2.0 CPU uses an Intel® Atom™ Dual Core Processor,
Intel Graphics Media Accelerator, 1GB DDR2 Memory, four (4) RS-232 Ports, six (6) USB 2.0 ports, two
(2) PS/2 interfaces for keyboard/mouse, 16GB Compact Flash and Video capture card.
Note: The AutoTrak 2.0 CPU may be subject to change in cosmetics due to the extraordinarily turbulent nature of the PC industry,
parts availability and model year upgrades. If changes are made, Vaddio will be certain to make changes in the documentation
accordingly.
An important feature: After the AutoTrak 2.0 CPU and software is configured using the mouse, keyboard
and monitor, these I/O devices can be removed to prevent any unauthorized access to the system. To
reattach the mouse and keyboard, the system will need to be rebooted to recognize these devices.
Front Panel Controls of AutoTrak 2.0 Worldwide CPU:
1) Power Indicator: Illuminates when power in on
2) Hard Drive Activity Indicator: Indicates when solid state drive is active
3) Recessed Reset Switch: A Momentary press of this switch resets the system and prepares the
CPU for an orderly shut-down. When the green light blinks, it is ready to be turned off or it is safe
to restart (power cycle).
4) USB Ports: Two (2) Front Panel USB Ports
Rear Panel of AutoTrak 2.0 Worldwide CPU:
1) Power Receptacle: IEC60320 C14 for power cable
2) Power Switch: Turns ON/OFF AutoTrak 2.0 CPU
NOTE: Do not turn the power off with the power switch on the rear panel or rack
power switch unless the computer has been shut down first. Repeated power
cycling without shutting down the computer first will cause harm to the system
(like all other business computers) and any warranties will be voided.
3) COM PORT 1: RS-232 Port for HD-18 IR Reference Camera
4) COM PORT 2: RS-232 Port for HD-18 Tracking Camera
5) COM PORT 3: Use RS-232 Port 3 when AutoTrak 2.0 is used with the AutoTrak POD or the
AutoPresenter 6x1 HD Switcher
6) RGBHV (on DE-15) Output: To setup and view software menus (800 x 600 @ 60Hz)
7) Ethernet Ports: Not used with AutoTrak 2.0 Application
8) USB Ports: Four USB Ports on the back panel for use with Keyboard, Mouse and USB Flash
Drive
9) Audio I/O: Not used with AutoTrak 2.0 Application
10) Video Input Port: Plug the HD-18 IR Reference Camera into the center yellow composite video
connector
①②
④⑤
Shut Down
CPU First
AutoTrak 2.0 Camera Tracking System
AutoTrak 2.0 Camera Tracking System - Document Number 342-0382 Rev. E Page 7 of 52
The IR Lanyard and Belt Pack for use with the AutoTrak 2.0 Camera Tracking Systems:
999-7250-000 and 999-7260-000 North America
999-7250-001 and 999-7260-001 International
1) IR Lanyard: Cloth covered flat flex circuit with IR LEDs terminates at the Central Medallion
2) Central Medallion: Supplies a connection point for the flat flex cable, contains an integrated
condenser microphone and a rubber over-molded cable strain relief that attaches the 32” cable.
3) 32” (813mm) Cable: Terminates the Central Medallion to the Belt Pack with a 5-Pin Mini XLR-F
connector.
4) Belt Pack: Holds power circuitry, wireless microphone transmitter, transmitter frequency control
switches (see pages 6-7) and rechargeable lithium battery pack.
5) Belt Pack Front Panel Controls: The System on/off controls and LED indicator as well as the
Microphone on/off controls are located on the Belt Pack Control Panel (see page 6-7).
6) Belt Clip: To clip the Belt Pack on a belt like device that the presenter wears.
7) Antenna: 1” (25.4mm) ¼-wave RP-SMA straight antenna to transmit RF wireless audio at 2.4 GHZ
utilizing Adaptive Frequency Hopper (AFH) from the integrated unidirectional microphone element.
The Lanyard’s Central Medallion Clothing Clips:
The system is shipped with two types of clothing clips to keep the
unidirectional mic built-in to the medallion facing the right direction and
keep it from flopping around when the presenter moves their hands and
arms to make a point.
1. A Triple Circle Magnet is a 2-piece magnetic kit meant to attach the
central medallion to the presenter’s clothes with magnets.
Peel off the adhesive backing cover and place the metal plate to the
back of the medallion and push to make good contact
Place the Central Medallion next to the clothing (shirt or dress) and
from the back side of the clothing attach the magnet. The magnet
will hold the medallion firmly against the clothing.
Note: Please do not use the magnet solution if the presenter
has a pacemaker or implantable cardioverter-defibrillator (ICD).
Magnets can negatively affect the operation of these medical
devices. The magnet side is labeled with a caution to warn the
user. Use only the Cable Clip for pacemaker and ICD patients
2. Additionally, an Audio-Technica AT8439 Cable Clip is also included.
This clip for clothing is a small and is to be attached to the cable just
below the central medallion’s cable strain relief. The clip will hold the
medallion firmly to the clothing
Note: Do not fold the Lanyard Necklace at any time as it contains a
flexible circuit that may cease to work if the necklace is hard folded.
Attach Cable
Clip to a point
just below the
strain relief.
Attach metal plate
with the adhesive
backing to the back of
the medallion. Use
the triple magnets to
attach trough clothing.
AutoTrak 2.0 Camera Tracking System
AutoTrak 2.0 Camera Tracking System - Document Number 342-0382 Rev. E Page 8 of 52
Belt Pack Control Panel
1) Lanyard Cable Connector (5-pin mini XLR - M): Plug the cable attached to the Lanyard into
the mini XLR connector to allow audio to be received by the Belt Pack and for power to be
provided to the IR LEDs in the Lanyard.
2) Radio: This LED indicates an active radio link with the EasyTalk AutoTrak 2.0 Wireless Audio
Interface. Solid blue LED indicates connection with the AutoTrak 2.0 Wireless Audio Interface.
Flashing blue LED indicates radio link has been lost.
Note: Radio link operates up to 100 feet line of sight of the AutoTrak 2.0 Wireless Audio
Interface.
3) System Power: To use the Belt Pack or IR Lanyard, turn the SYSTEM POWER switch to the on
position and the LED will illuminate. Be sure to turn off the SYSTEM POWER switch when the
system is not in use to save the battery life. The Rechargeable Lithium Ion Battery Pack provides
up to ten (10) hours with full charge.
Note: It is highly recommended that the Rechargeable Lithium Ion Battery Pack be
fully charged prior to using the Belt Pack for the first time!
4) Microphone ON/OFF: This switch turns the wireless microphone on or off at the Belt Pack
allowing the presenter to use an existing room system microphone instead, or for momentary
microphone muting.
Note: The System Status light on the EasyTalk AutoTrak 2.0 Wireless Audio Interface will light if
the microphone signal is detected. If the Microphone is turned off at the Belt Pack, the System
Status light will not light.
5) 1” ¼-Wave Antenna: Used to transmit the wireless microphone audio back to the AutoTrak 2.0
Wireless Audio Interface.
③④
AutoTrak 2.0 Camera Tracking System
AutoTrak 2.0 Camera Tracking System - Document Number 342-0382 Rev. E Page 9 of 52
Belt Pack Views:
Belt Pack and Battery Compartment:
1) Removable Battery Compartment Cover: To open, carefully press down at the top of the
Removable Battery Cover near the center of the small opening and slide the cover downward. To
replace the Removable Battery Cover, start sliding the cover on at the bottom of the Battery Pack
Compartment and slide cover upward to the top to the small opening until the cover latches in place.
2) Micro-B USB Charging Port: The Belt Pack rechargeable battery can be charged by the micro-B
USB connector on the bottom side of the belt pack enclosure. A USB charger is included with the
Belt Pack. The Belt Pack can also be recharged by using a micro-B USB to USB adapter which can
be connected to a PC or Laptop USB port for recharging. Use only the charging power supply
provided.
3) Dip Switches: There are two (2) 4-position dip switches located on the circuit board, SW4 and SW5.
They provide configuration settings for Microphone Gain Control, Filtering, Compression and
Microphone Filtering and Pairing of the Wireless Belt Pack to the AutoTrak 2.0 Wireless Audio
Interface.
4) Rechargeable Lithium Ion Battery: The battery is housed and attached inside the Battery
Compartment and under normal use should last up to ten (10) hours when fully charged.
5) Battery Indicator LED: The Battery Indicator LED is located on the bottom of the Belt Pack.
When the USB Charger is not connected to the Belt Pack: The Battery Indicator LED will be
off when battery power is adequate for the Belt Pack. The Battery Indicator LED will blink Red
indicating that the battery power is low and needs to be recharged soon.
When the USB Charger is connected to the Belt Pack: The Battery Indicator LED will be
Yellow when the battery is charging. The Battery Indicator LED will be Green when the battery is
fully charged. Average charging time from dead battery to full charge is 10 hours.
6) Radio Pairing Button SW3: push this button in conjunction with the Pairing button on the front panel
of the Optional Wireless Receiver to “pair” the transmitting Belt Pack with the Receiver.
AutoTrak 2.0 Camera Tracking System
AutoTrak 2.0 Camera Tracking System - Document Number 342-0382 Rev. E Page 10 of 52
Belt Pack Dip Switch Settings:
Belt Pack Configuration Settings:
The Belt Pack has a number of custom settings that can be enabled or disabled for specific applications.
These settings can be applied by activating dip switch settings on the two (2) 4-position dip switches SW4
and SW5 located on the Belt Pack Circuit Board.
Switch Set 4:
SW4: Dip Switch 1 - Not Used
SW4: Dip Switch 2 - IR Transmitter: ON enables the IR Transmitter LED’s in the IR Lanyard. OFF
disables the IR Transmitters in the Lanyard and the camera tracking will not function.
SW4: Dip Switch 3 - Radio in Belt Pack: ON enables the Radio circuit in the Belt Pack. OFF
disables and will turn off the Radio circuit to increase battery life. Make sure this switch is in the ON
position for use with Audio Interface (if applicable). It ships from the factory in the OFF position.
Note: Turn OFF Dip Switch 3 when not using the optional EasyTalk AutoTrak 2.0
Wireless Audio Interface with the AutoTrak 2.0 System.
SW4: Dip Switch 4 - Clear Pairing: ON clears the pairing setting of the receiver in the Belt Pack.
.
Switch Set 5:
SW5: Dip Switch 1 - 3dB Gain Boost: Enable adds a three (3) dB gain to the microphone audio.
Disable provides zero gain.
SW5: Dip Switch 2 - 6dB Gain Boost: Enable adds a six (6) dB gain to the microphone audio.
Disable provides zero gain.
SW5: Dip Switch 3 - 9dB Gain Boost: Enable adds a nine (9) dB gain to the microphone audio.
Disable provides zero gain.
Note: The following Gain Boost Switches, 1 through 3, can be used individually or in
combination. For example, if Dip Switch 1, 3dB Gain and Dip Switch 2, 6dB Gain are
both ON, they will add a total of 9 dB of gain
SW5: Dip Switch 4 - Automatic Gain Control: ON enables an Automatic Gain Control function that
maintains a constant audio level to regulate soft talkers as well as loud talkers. OFF disables the
Automatic Gain Control, of course.
Optional: AutoTrak 2.0 Wireless Audio Interface for AutoTrak 2.0 Systems:
Switch
Number
Dip Switch Function
Switch Set 4
1 Not Used
2 ON/OFF - IR LED’s in Lanyard
3 ON/OFF - Radio in Belt Pack *Turn off when not
using Optional EasyTalk Wireless Receiver
4 Clear Pairing (pairing is required for proper operation)
Switch Set 5
1 ON/OFF: ON adds 3dB Gain Boost on Microphone
2 ON/OFF: ON adds 6dB Gain Boost on Microphone
3 ON/OFF: ON adds 9dB Gain Boost on Microphone
4 ON/OFF: Automatic Gain Control Mode
SW3
SW4
SW5
AutoTrak 2.0 Camera Tracking System
AutoTrak 2.0 Camera Tracking System - Document Number 342-0382 Rev. E Page 11 of 52
998-7230-000: EasyTalk AutoTrak 2.0 Wireless Audio Interface-North America
998-7230-001: EasyTalk AutoTrak 2.0 Wireless Audio Interface-International
Front Panel Controls
1) Power ON/OFF: This switch turns the power for the AutoTrak 2.0 Wireless Audio Interface on or off.
To use, push the power button until the blue LED is lit and the system is ready for operation.
2) Pair: This button initiates the automatic pairing (Pairing is the matching of the same Adaptive
Frequency Hopper AFH hopping sequence for both devices) for the Belt Pack Radio Transmitter and the
AutoTrak 2.0 Wireless Audio Interface Radio Receiver in the AutoTrak 2.0 Wireless Audio Interface.
3) Mute: This control mutes (turns off) the audio outputs of the AutoTrak 2.0 Wireless Audio Interface.
4) Volume: The + (plus) and – (minus) buttons are used to raise and lower the audio outputs (Balanced
and Unbalanced) from the AutoTrak 2.0 Wireless Audio Interface.
5) Audio Level: This LED display will indicate the relative audio level output (from all sources) of the
AutoTrak 2.0 Wireless Audio Interface. Red Line at the top of the LED Display indicates clipping of the
audio signal.
6) Radio, EQ Filter and Compressor Status LED’s:
Radio LED: Solid blue light indicates normal operations. Fast flashing indicates no link
established with the Belt Pack Wireless Microphone. Slow flashing indicates the Pairing cycle is in
progress.
EQ Filter: Blue light on indicates the EQ Filter is turned on. Blue light off indicates the EQ Filter is
off. When EQ Filter is enabled, it helps increase speaker intelligibility for voice applications.
Compressor: Solid blue light indicates that the Compressor is on. No light indicates that the
Compressor is off. Compressor on minimizes the potential of “clipping” by attenuating the audio
signals that exceed the maximum output levels.
7) Antenna: The 4” antenna is tuned to receive 2.4 GHZ signals from the IR Lanyard Belt Pack
Microphone. Note: If the AutoTrak 2.0 Wireless Audio Interface is installed deep inside a metal
equipment rack or is surrounded by other metal cased equipment, the antenna may need to be
extended away from the rack to improve reception.
Optional Antenna Extension Kit
The Audio Interface has an Optional Antenna Extension Kit available which will add
approximately 6dB gain to the system and extend the front panel receiver antenna to a
base antenna that would sit on top of the rack. It also includes a longer ½ wave whip
RP-SMA antenna for the belt pack.
See part number: 999-1234-000.
①② ⑤⑥
Optional Antenna
Extension Kit
AutoTrak 2.0 Camera Tracking System
AutoTrak 2.0 Camera Tracking System - Document Number 342-0382 Rev. E Page 12 of 52
Optional: AutoTrak 2.0 Wireless Audio Interface/Rear Panel Connections
1) 12 VDC, 1.0 Amp Power Connector: The 5.5mm OD and 2.5mm ID power connector should be
plugged into the PowerRite power supply provided by Vaddio. Use of any unauthorized power
supplies will void any and all warranties.
2) RS-232 Control: The DB-9 female connector is provided for 3
rd
party control systems using the
Wireless Audio Interface Application Protocol Interface (API). See the Command List.
3) Settings (8-Position Dip Switch): The eight position dip switch is used for system configuration of
the AutoTrak 2.0 Wireless Audio Interface:
Dip Switch 1 - Compressor: Enable adds a Dynamic Range Compressor for the Audio Line
Level Outputs (balanced or unbalanced). Disable turns it off.
Dip Switch 2 - Speaker EQ Filter: Enable adds a specialized output filter for improved
intelligibility for voice applications. Disable turns it off.
Dip Switch 3 - ON Position/USB Conference Mode: Enable (Dip Switch 3 On) creates the
desired audio mixing (Near and Far ends) for USB conferencing applications such as Skype.
Disable turns off the USB Conference Mode.
o Note: In the USB Conference Mode, the PC USB Speaker Audio is sent to the balanced and
unbalanced audio line outputs, which allows the Far End Audio to be presented in the room.
The Belt Pack Wireless Microphone Audio is also sent to the PC to send to the Far End.
o The AutoTrak 2.0 Wireless Audio Interface will also be recognized as a USB Audio Device by
the PC with recording (the Belt Pack Wireless Microphone Audio) and playback (the Speaker
Audio) capabilities. Disable turns the USB Conference Mode off.
Dip Switch 3 - OFF Position/USB Record Mode: Disable (Dip Switch 3 Off) creates a USB
Record Mode for PC Audio Recording (PC requires Audio Recording Software-not included) and
Playback through the USB port (Audio output through the Balanced or Unbalanced Audio Line
Outputs).
o The AutoTrak 2.0 Wireless Audio Interface will be recognized as a USB Audio Device by the
PC with recording (the Belt Pack Wireless Microphone Audio) and playback (the Speaker
Audio) capabilities.
Dip Switch 4 - Radio ON/OFF: ON enables the Radio Receiver for the Wireless Microphone on.
OFF turns it off, naturally.
Dip Switch 5 - Baud Rate Selection ON/OFF: OFF sets the Baud Rate to the default 9600bps.
ON sets the Baud Rate to 38400bps.
Dip Switch 6 - Front Panel Buttons Lock ON/OFF: ON locks the Front Panel Buttons and
disables the buttons from functioning. OFF allows the front panel buttons to be used.
Dip Switch 7 - Software Control ON/OFF: When ON, dip switches 1, 2, 3, 4, and 8 are ignored
to allow full serial control of the audio interface
Dip Switch 8 - Resets to Factory Defaults ON/OFF: When ON and power is plugged in, the
interface is set to factory defaults. Leave OFF for normal operation.
①②⑤⑥
AutoTrak 2.0 Camera Tracking System
AutoTrak 2.0 Camera Tracking System - Document Number 342-0382 Rev. E Page 13 of 52
4) GPIO Port: The GPIO Port provides the ability to interface with external control systems. Inputs
are logic level low. Output is an open collector.
Pin Function
1
Power (12 VDC)
2
Mute Toggle (Input)
3
Mute Status (Output)
4
Volume Up (Input)
5
Volume Down (Output)
6
Not Used
7
Ground
5) USB Type B Connector: This connector is used to interface with the Host PC for soft-client
codec type applications.
6) Audio Outputs: There are two (2) Audio Outputs on the rear panel:
Balanced Audio Output Jack: Balanced Line Level (on XLR - M connector) +4dBu
Unbalanced Audio Output Jack: Unbalanced Line Level (on RCA-F connector) -10dbV
Pairing Procedure for Belt Pack Pairing with the AutoTrak 2.0 Wireless Audio Interface:
A. Place the Belt Pack in close proximity to the AutoTrak 2.0 Wireless Audio Interface.
B. Remove the Battery Compartment Cover: To open: See top of page 9.
C. Locate Pairing Button Switch labeled SW3. Press the button and release. The Radio LED on the
Belt Pack will begin blinking at a slow rate.
Important Note: The Pairing button on the AutoTrak 2.0 Wireless Audio Interface must
be pushed within ten (10) seconds of pressing the pairing button SW3 on the Belt Pack or
pairing will not occur!
D. Press the Pair Button on the front panel of the EasyTalk AutoTrak 2.0 Wireless Audio Interface.
E. The Belt Pack and the AutoTrak 2.0 Wireless Audio Interface will automatically sync with each
other. The blue Radio LED’s on the Belt Pack and the AutoTrak 2.0 Wireless Interface will
illuminate solid blue indicating they are paired and ready for operation.
Lanyard, Belt Pack Controls:
The central medallion of the lanyard has an attached, strain-relieved, 32” cable
that terminates to a 5-pin mini XLR female connector. Attach the 5-pin mini XLR
to the 5-pin mini XLR male connector on the belt pack. The microphone element
is on the top of the central medallion. The lanyard material houses a flat flex type
circuit where the IR LEDs are mounted. After the initial setup is complete, the
presenter should slip the lanyard over their head and position the medallion away
from the presenter and face the Vaddio logos on the lanyard cloth cover out,
toward the cameras. Clip the belt pack onto the clothing, belt or waistband
securely. Please avoid dropping the belt pack! A smashed Belt Pack isn’t a
happy thing. However, replacements are available.
Power to illuminate the IR LEDs is supplied from the Belt Pack and if the System
Power Switch is ON, the IR LEDs will illuminate at 850 nanometers (out of the
range of visible light for mere humans). Each Lanyard has 15 IR LEDs spread
out evenly throughout the Lanyard Necklace. This invisible light is picked up by
the IR reference camera of the AutoTrak 2.0 System and information is sent to
the Tracking Camera in order to follow the presenter throughout the presentation
environment.
Central
Medallion
32” Cable to
Belt Pack
Mic
Element
24”
Lanyard
Necklace
AutoTrak 2.0 Belt
Pack and Lanyard
Belt Pack
Note: Do not fold the Lanyard Necklace at any time as it contains a
flexible circuit that may cease to work if the necklace is hard folded.
Folding the Lanyard Flex Circuit will void any and all warranties.
AutoTrak 2.0 Camera Tracking System
AutoTrak 2.0 Camera Tracking System - Document Number 342-0382 Rev. E Page 14 of 52
Basic System Configuration 1:
AutoTrak 2.0 999-7250-000 Dual HD-18 Kit with Quick Connect DVI/HDMI Interface (North America Only)
Power to Camera
Differential HSDS Video from Camera
CVBS
BNC to RCA
Cat-5e
Power to
EZ
Port
Power to
Camera
CVB from
Camera
RS-232
Cat-5e
Std Quick-Connect
Box 998-1105-001
24 VDC
PWR
Supply
CVBS in
Video 2
Keyboard & Mouse
RGBHV Monitor
(
Not Included
)
Optional Wireless Audio
EasyTalk AutoTrak 2.0 Wireless Audio Interface
Receiving Audio from Wireless Belt Pack at 2.4 GHz
Instructor’s Confidence
Monitor
(Not Included)
Simulated Video Feed
24 VDC
PWR
Supply
Quick-Connect DVI/HDMI - SR
Interface 998-1105-018
AutoTrak 2.0 IR Lanyard,
attached cable, Rechargeable
Belt Pack and 1-inch RP-SMA
Cat-5e
Cat-5e
HD-18
IR Reference
Camera with
Adapters and
Filters
Composite Video
feed to AutoTrak
2.0
HD-18
Tracking Camera
AutoTrak
2.0
Dual HD-18
Mount
HD Video Monitors
(Not Included)
Really Simulated Video Feeds
Note: Belt Pack is capable of
transmitting Wireless Mic Audio at 2.4
GHz to Optional EasyTalk AutoTrak 2.0
Wireless Audio Interface
Cat-5e
Cat-5e Cable to EZ Power Video Port
Sound System
(Not Included)
Balanced Line Level (on XLR +4dBu) or
Unbalanced Line Level (on RCA -10dBV)
RGBHV
Cat-5e
Cat-5e
4” RP-SMA
Antenna
YPbPr
DVI-D or
HDMI with
adapter
HDMI
Video
C60 Codec
(
Not Included
)
AutoTrak 2.0 CPU
Port 2
Port 1
Serial to Cat-5e
Control Adapters
Use Adapter P/N:
998-1001-232 on
these Ports
AutoTrak 2.0 Quick-Connect
Box 998-1105-020
AutoTrak 2.0 Camera Tracking System
AutoTrak 2.0 Camera Tracking System - Document Number 342-0382 Rev. E Page 15 of 52
Basic System Configuration 2:
AutoTrak 2.0 999-7260-000
HD-18 IR Reference Camera and HD-20 Tracking Camera Kit with Quick Connect DVI/HDMI
Interface (North America Only)
Power to Camera
Differential HSDS Video from Camera
CVBS
BNC to RCA
Cat-5e
Power to
EZ
Port
Power to
Camera
CVBS
from
Camera
RS-232
Cat-5e
Std Quick-Connect
Box 998-1105-001
CVBS in
Video 2
Keyboard & Mouse
RGBHV Monitor
(
Not Included
)
Instructor’s Confidence
Monitor
(Not Included)
Simulated Video Feed
Quick-Connect DVI/HDMI - SR
Interface 998-1105-018
AutoTrak 2.0 IR Lanyard,
attached cable, Rechargeable
Belt Pack and 1-inch RP-SMA
Cat-5e
Cat-5e
HD-18
IR Reference
Camera with
Adapters and
Filters
Composite Video
feed to AutoTrak
2.0
HD-20
Tracking Camera
AutoTrak
2.0
HD-18-
HD-20
Mount
HD Video Monitors
(Not Included)
Simulated Video Feeds
Note: Belt Pack is capable of
Transmitting Wireless Mic Audio at 2.4
GHz to Optional EasyTalk AutoTrak
2.0 Wireless Audio Interface
Cat-5e
Cat-5e Cable to EZ Power Video Port
AutoTrak 2.0 Quick-Connect
Box 998-1105-020
Sound System
(Not Included)
Balanced Line Level (on XLR +4dBu) or
Unbalanced Line Level (on RCA -10dBV)
RGBHV
Cat-5e
Cat-5e
4” RP-SMA
Antenna
YPbPr
DVI-D or
HDMI with
adapter
HDMI
Video
T C60 Codec
(
Not Included
)
AutoTrak 2.0 CPU
Port 2
Port 1
Serial to Cat-5e
Control Adapters
Use Adapter P/N:
998-1001-232 on
these Ports
Optional Wireless Audio
EasyTalk AutoTrak 2.0 Wireless Audio Interface
Receiving Audio from Wireless Belt Pack at 2.4 GHz
24 VDC
PWR
Supply
24 VDC
PWR
Supply
AutoTrak 2.0 Camera Tracking System
AutoTrak 2.0 Camera Tracking System - Document Number 342-0382 Rev. E Page 16 of 52
The AutoTrak 2.0 CPU, Camera and Software Operating Instructions
The AutoTrak 2.0 CPU is a 1-RU rack
mount computer that comes preloaded
with the AutoTrak 2.0 software. It is a
closed system based on a Linux operating
system.
One More Time: The AutoTrak 2.0 CPU is a computer running a Linux OS. Please do not remove power from the AutoTrak 2.0
CPU without first shutting the system down, as you would any other business computer. It is safe to remove power only after the
AutoTrak 2.0 CPU has been shut down. Consistently power cycling the CPU with the Rear Power Switch will eventually wreck the
AutoTrak 2.0 CPU and void the warranty.
The AutoTrak 2.0 CPU uses an Intel® Atom™ Dual Core Processor, Intel Graphics Media Accelerator,
1GB DDR2 Memory with six (6) USB ports, four (4) RS-232 Ports, two (2) PS/2 interfaces for
keyboard/mouse, 16GB Compact Flash and Video capture card. CPU specifications and cosmetics are
subject to change.
Getting Started:
1) Take the AutoTrak 2.0 CPU out of the box (typical) and start the system connection.
2) Connect two (2) of the 998-1001-232 control adapters (check part numbers carefully) to serial com
ports 1 and 2. The IR Reference camera will be connected to Port 1 and the Tracking Camera will be
connected to Port 2.
3) Connect the Keyboard and the Mouse to the AutoTrak 2.0 CPU using USB ports
4) Connect the computer monitor (not included) to the DE-15 (HD-15) on the AutoTrak 2.0 CPU.
5) Connect the AC Power Cord, but do not turn on the computer yet.
Mounting Cameras and Distance Limits:
The AutoTrak 2.0 systems are shipped with
either dual HD-18 cameras and mount or
an HD-18 and HD-20 cameras and mount
that can be mounted to a wall permanently
or mounted to an optional cart system. The
vertically stacked camera arrangement is
required for the AutoTrak 2.0 software to
track properly
.
Consider the placement of the cameras
carefully; the range of use is from 12’
(3.65m) and up to 40’ (12.2m). System
positioning is critical for proper and
consistent operation. If the distance from
the presenter to the wall mounting location
is greater than 40’ (12.2m), then an optional
portable cart system is recommended to
place the cameras in range of the IR
Lanyard, which is required for the tracking
system to acquire the IR LED light in order
to track the presenter.
Mount the cameras with the IR Reference Camera on the top shelf of the dual mount and mount the
Tracking Camera on the lower shelf of the dual mount.
Please mark and test all cables prior to termination. Please do not connect
these cameras to the Quick-Connect systems using the “guess/trial and error”
method. Plugging the EZ POWER/VIDEO Cat. 5 Cable into the wrong RJ-45
may cause damage to the camera system and void the warranty!
AutoTrak 2.0
HD-18
IR Reference
Camera with
Adapters and
Filters
AutoTrak 2.0
HD-18
Tracking
Camera
Dual Mount
AutoTrak 2.0
HD-20
Tracking
Camera
AutoTrak 2.0
HD-18
IR Reference
Camera with
Adapters and
Filters
AutoTrak 2.0 999-7260-000
HD-18 IR Reference
Camera and HD-20
Tracking Camera
AutoTrak 2.0 999-7250-000
Dual HD-18 Cameras for
IR Reference and Tracking
Cameras
Dual Mount
Guessing Bad
AutoTrak 2.0 Camera Tracking System
AutoTrak 2.0 Camera Tracking System - Document Number 342-0382 Rev. E Page 17 of 52
Installing the PTZ Cameras
The IR Reference Camera requires two (2) Cat-5e cables run from the head-end
equipment; one for composite video and power, and one for control. The installation
steps for the IR Reference Camera are as follows:
1) Identify the IR Reference Camera, the HD-18 with the 37mm lens adapter on the lens
2) Make sure the 37mm to 58mm adapter ring is in place
3) Make sure the 58mm polarizing filter is in place
4) Make sure the 58mm band-pass IR filter is in place
5) Mount this camera to the top shelf of the dual mount with the supplied ¼”-20 screws.
6) Connect the 18”/45.8mm BNC to RCA Video Cable to the Composite (CVBS) BNC-M video connector on the
back of the camera and connect the RCA-M connector to the RCA–F connector on the AutoTrak 2.0 Quick-
Connect Box 998-1105-020.
7) Connect one side of the 12”/30.48cm Cat-5e Patch Cable to the EZ Power Video RJ-45 connector on the
camera and the other end of the cable to the AutoTrak 2.0 Quick-Connect Box 998-1105-020 to the end marked
“IR Reference Camera”. This connector is only providing power to the EZ Power Video Port.
8) Connect the 1
st
Cat-5e cable (up to 100’/30.5m not supplied) to the AutoTrak 2.0 Quick-Connect Box 998-1105-
020 to the RJ-45 port labeled “AutoTrak 2.0”. This Cat-5e cable is terminated at the head end to the other
Quick-Connect Box (998-1105-001) RJ-45 connector.
9) Take the composite output of the Quick-Connect Box 998-1105-001 and connect it to the AutoTrak 2.0 CPU
composite video input (you’ll need a RCA-M to RCA-M cable, which is not supplied) to the center yellow
composite input on the back of the AutoTrak 2.0 CPU.
10) Connect the 2
nd
Cat-5e cable (up to 100’ /30.5m - not supplied) to the RS-232/IR port on the camera, and at the
head-end connect it to the Control Adapter that is on COM PORT 1 on the CPU.
11) Connect the 24VDC power supply to the 998-1105-001 Quick-Connect Box.
The Tracking Camera requires two (2) Cat-5e cables run from the head-end equipment; one for YPbPr
HD video and power, and one for control. Note: AutoTrak 2.0 999-7250-000 includes a HD-18 Camera
for Tracking and 999-7260-000 includes a HD-20 Camera for Tracking.
1) Identify the HD-18 or HD-20 Tracking Camera (the normal camera without the 37mm lens adapter).
2) Mount this camera on the lower shelf of the mount with the supplied ¼”-20 screws.
3) Run one Cat-5e (up to 100/30.5m) cable between the EZ Power Video Port on the HD-18 or HD-20 Tracking
Camera to the EZCamera Power & HD Video Port on the Quick-Connect DVI-HDMI-SR Interface 998-1105-018.
4) Connect the HD Video DVI-D or the YPbPr output (or both) to a high definition monitor
5) Run the 2nd Cat-5e from the RS-232/IR port on the back of the HD-18 or HD-20 Camera to Control Adapter that
is connected to COM PORT 2 on the AutoTrak 2.0 CPU.
6) Connect the 24VDC Power supply to the Quick-Connect DVI-HDMI-SR Interface.
Booting up the System and Initial Set-up:
1) With the AutoTrak 2.0 Belt Pack on (at least the system power switch on) and the lanyard plugged into the belt
pack (with the battery fully charged), place the lanyard/belt pack in a centered location approximately 20’
(6.096m) from the AutoTrak 2.0 stacked camera assembly and about 5’ (1.524m) off the floor to imitate the
height of a presenter/instructor.
2) Turn on the cameras and AutoTrak 2.0 CPU. The AutoTrak 2.0 CPU should boot up to the AutoTrak 2.0
application automatically. Click the Pause button to enter setup. The screen shot is below:
AutoTrak 2.0 Camera Tracking System
AutoTrak 2.0 Camera Tracking System - Document Number 342-0382 Rev. E Page 18 of 52
Note: If AutoTrak 2.0 CPU green light is blinking (which indicates standby mode), restart system by:
Turn the rear mounted Power Switch OFF for a few seconds and then back ON - or - remove
CPU power and then restore it - or - push the recessed Restart Button for a few seconds and
then release it.
3) Plug the IR Reference Camera into a monitor for set-up purposes. With the IR Reference plugged
into a monitor, the IR LEDs should be visible as white dots on a black background. These LEDs will
be tracked as the presenter moves around the room. To aid in set-up, a temporary RCA Y-cable may
be used to split the signal between the monitor and CPU.
4) Select the Presets Tab, then the Reference Camera Tab. Use the Position buttons to Center
the IR lanyard in the monitor display horizontally and vertically.
5) Use the Zoom buttons (tele & wide) to increase the size of the lanyard in the display until it is
approximately 1/3 the size of the video image on the monitor. Use the Position up/down buttons to
locate the lanyard in the center of the screen so the presenter’s head is in the top ½ of the screen.
6) The Pan speed and the Tilt speed adjusts for the Reference camera’s speed to the Home
position.
7) The Custom Home position allows the user to define an alternate Default Home position for the
Reference and Tracking cameras (i.e. presenter’s lectern position, which is not always the dead
center of the room).
8) Click the Save button to save this default zoom and tilt position for the IR Reference Camera. The
Load button is for recalling a previously saved preset.
9) Plug the composite video from the IR Reference Camera back into the middle yellow RCA-F jack on
the back of the AutoTrak 2.0 CPU.
AutoTrak 2.0 Camera Tracking System
AutoTrak 2.0 Camera Tracking System - Document Number 342-0382 Rev. E Page 19 of 52
10) With the Tracking Camera plugged into a monitor, select the Presets Tab and then the Tracking
Camera Tab. Adjust the Position buttons and the Zoom buttons to tilt/zoom the camera to the
desired presenter framing. Set the zoom position and the tilt angle of the Tracking Camera and click
on the Save Preset Button to store the System Tracking Preset. The Load button is for recalling
a previously saved preset.
Note: The AutoPresenter Camera Presets are supported by AutoTrak 2.0 when used in conjunction
with an AutoTrak POD or a AutoPresenter 6x1 HD Seamless Switcher and Automated Camera Preset
Controller. A later section explains the connectivity and set-up when using these devices together.
AutoTrak presets can be assigned to any AutoPresenter trigger input. Pan and tilt speeds are set on an
individual preset basis as well. When set, the Save button will save the Tracking camera preset
configuration. The Load button recalls previously stored presets. Check the Disable Tracking during
presets checkbox if you wish the IR Reference camera to not follow the IR lanyard while the Tracking
camera is driven to a preset location. Typically, the presenter will remain near the preset location, and
won’t require searching for the lanyard when tracking resumes. If the lanyard is not in the shot when
tracking resumes, the IR Reference will then search for the lanyard.
AutoTrak 2.0 Camera Tracking System
AutoTrak 2.0 Camera Tracking System - Document Number 342-0382 Rev. E Page 20 of 52
1) On the Tuning / Tracking Camera page, Camera Select automatically detects the camera
being used as the Tracking Camera. The auto-detect choices are between the HD-18 and HD-20.
2) The Iris control allows the user to set the specific f-stop (iris value) of the camera for challenging
lighting environments or use the system in Automatic mode. The system will auto set this value.
3) The Auto Focus Type allows the user to select the type of auto focus that is preferred. The Low and
Bright Light setting is effective for bright to low light conditions. The Low Light setting allows for faster
focusing in low light conditions. The system will auto set this value.
4) The Tilt Correction angle is to compensate for the different heights of the camera lens when the
HD-18 cameras are mounted in a co-linear stacked array which is a highly preferred and
recommended configuration. This correction angle is automatically figured by the system when the
Tracking Camera Preset or the Reference Camera Preset is saved assuring that both cameras are
pointing at the same target.
5) The Zoom Position is a reference position stored as part of the system Tracking Camera Preset.
6) The Pan Correction parameter should only be used: if there is absolutely no way that the
cameras can be stacked in a co-linear array and have to be used side by side. The side by side
configuration is not recommended. The stacked configuration is highly preferred.
7) Auto or Manual White Balance. In Manual mode, access to the Red and Blue levels is allowed to
manually adjust the camera’s color/white balance.
8) To start AutoTrak 2.0 click the Resume button.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52

VADDIO AutoTrak 2.0 Installation and User Manual

Category
Camera accessories
Type
Installation and User Manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI