MiraScreen Doando User manual

Brand: MiraScreen

Model: Doando

Type: User manual

MiraScreen Doando is a wireless HD transmitter and receiver kit that allows you to stream content from your computer or other devices with HD video output to your TV or monitor. It supports pairing with Ezcast TX devices and has a privacy mode that can be activated by tapping the transmitter function button. The MiraScreen Doando is easy to set up and use, simply connect the receiver to your TV or monitor and the transmitter to your computer or other device. Once connected, you can enjoy streaming your favorite content without the need for cables.

User manual

Ver. A 1.0

Wireless HD Transmitter

& Receiver Kit

Thank you for purchasing the MiraScreen products, For optimum

operation, please read this manual carefully before use.

Preface

Size:100*57mm

Connection Diagram

Problem solving

Q: How to restore factory settings?

A: When the product fails, press and hold the receiver function button

for 10 seconds. After a black screen appears and restart, the factory

settings will be restored.

Q: Can devices without HD interface be used?

A: Yes, please use the device with an HD interface converter.

Q: How to enter privacy mode?

A: Tap the transmitter function button to disconnect or reconnect.

1. Connect the HD port of the receiver to the video input port of the

display device such as the monitor or TV.

2. Connect the Micro power supply port of the receiver to the charging

cable and plug it into the power adapter ( Voltage above 5V, current above

2A). Turn on the Receiver power switch.

3. Adjust the HD Signal source of the monitor or TV to the corresponding

HD port untithe boot screen is displayed.

4. Connect the transmitter to the computer or other devices With HD video

output function . After the indicator Light enters the fast ﬂash state , Wait

for ten seconds to complete Casting.

*Please make sure that the power of the computer is suﬃcient. If the

power supply of the computer is insuﬃcient or HD is unable to supply

power , please connect the transmitter to the power adapter or Micro

power supply port ( Voltage above 5V , current above 2A )

Receiver -RX

Transmitter -TX

1. Please Press the receiver function button for more than 3 seconds, and

the prompt will pop up on the interface : Release the button to pair With

Ezcast TX. Wait for the transmitter to enter pairing mode

2. Press the transmitter function button for more than 5 seconds , the

indicator will ﬂash for pairing , and Wait for the transmitter indicator to be

always on,indicating that the connection is successful.

Receiver[RX]

Function Button

Transmitter[TX] - Function Button

Transmitter Indicator Status

Hardware Casting

Combination of receiver and transmitter, plug and play

Pairing Instructions

The product has been paired out of the factory. In case of pair ing failure

due to improper operation or other circumstances during use, it is

necessary to restore and re pair the device as follows:

Slow Flash Disconnected

Fast Flash Pairing

Always OnConnected

Micro Power

Supply Port

Micro Power

Supply Port

Indicator

Light

Indicator

Light

Function

Button

Function

Button

Waining:

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:(1) this device may not cause harmful interference,

and (2) this device must accept any interference received,including interference

that may cause undesired operation.

changes or modiﬁcations not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits

for a Class B digital device,pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful inter ference

in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However,there is no guarantee that interference will not occur in a particular

installation.If this equipment does cause harmful interference to rradio or

television reception. whtch can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by one

or more of the following measures:

--Reorient or relocate the receiviong antenna.

--Increase the separation betweeb the equipment and receiver.

--Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

--Consult the dealer or an experienceed radio/TV techinician for help.

NOTE: This device and its antenna(s) must not be co-located or operation in

conjunction with any other antenna or transmitter

RF Exposure Statement（Only for RX）

To maintain compliance with FCC’s RF Exposure guidelines, This equipment

should be installed and operated with minimum distance of 20cm the radiator

your body.This device and its antenna(s) must not be co-located or operation

in conjunction with any other antenna or transmitter

MiraScreen Doando User manual

MiraScreen Doando User manual

MiraScreen Doando User manual

Other documents