Zeta ZTB6B Installation guide

Zeta
Brand
Zeta
Model
ZTB6B
Category
Fire protection
Type
Installation guide

Zeta ZTB6B is a fire alarm bell designed for indoor use. It has a rated voltage of 20.4 to 27.6Vdc and a rated current of 11mA@24Vdc. The bell has an operating temperature range of -10 to 50 degrees Celsius and an IP rating of 23C. It weighs 410g and has a red body color.

The Zeta ZTB6B is a versatile fire alarm bell that can be used in a variety of applications. It can be mounted on a flush or surface mounted BESA, single gang installation box, or directly onto the wall. A knockout is provided at the top of the base for surface wiring. The bell has a minimum mounting height of 2.4m above the floor.

Zeta ZTB6B is a fire alarm bell designed for indoor use. It has a rated voltage of 20.4 to 27.6Vdc and a rated current of 11mA@24Vdc. The bell has an operating temperature range of -10 to 50 degrees Celsius and an IP rating of 23C. It weighs 410g and has a red body color.

The Zeta ZTB6B is a versatile fire alarm bell that can be used in a variety of applications. It can be mounted on a flush or surface mounted BESA, single gang installation box, or directly onto the wall. A knockout is provided at the top of the base for surface wiring. The bell has a minimum mounting height of 2.4m above the floor.

INSTALLATION INSTRUCTIONS
Indoor Series,
150mm (6 inch) and 200mm (8 inch)
Fire Alarm Bell, Type A
Please ensure that the following instructions are
read carefully prior to installation.
1. Bells should be positioned a minimum of 2.4m
above the floor .
2. Remove gong by unscrewing allen/hex bolt.
3. Ensuring that the terminals are at the top of the
unit, feed field wiring through the base. Base
can be mounted either onto a flush or surface
mounted BESA, single gang installation box or
directly onto the wall. A knockout is provided at
the top of the base for surface wiring. (Fig 2/3)
4. Connect wiring (max 2.5mm ) to terminals (Fig
1) observing polarity. Dress wires to avoid
touching the gong.
5. Correctly align gong on base and replace
allen/hex bolt to secure.
, in the vertical plane
2
Fig 2: Semi-Flush Installation
Gong
Mounting
Screw
Please Note: Care should be taken to
avoid damage to the striker mechanism
BESA Box
or single gang
installation
box
Base
Knock-out for
surface wiring
Fig 3: Basic Mechanism and Gongs
150 or 200
Mounting holes are provided to suit either BESA single
gang installation boxes or for direct wall mounting.
60
53
BESA Box.
50.5
Mounting Holes (
Dimensions in mm)
(Polarised)
+
-
Base
IN INOUT OUT
Field Wiring
Max. 2.5mm
2
To next bell or
end-of-line
monitoring
device
From
control
panel
SPECIFICATION
Model ZTB6B/24 ZTB8B
Rated Voltage 20.4 to 27.6Vdc 20.4 to 27.6Vdc
Rated Current 11mA@24Vdc 17mA@24Vdc
Operating Temperature -10 to +50 C -10 to +50 C
IP Rating (minimum) 23C 23C
Weight 410g 640g
Body Colour Red Red
oo
Fig 1: Wiring (front view) Observe Polarity
Note: For sound output data refer to Sound Output Data Sheet DS/BELLDATA/ZETA/ISS1
Fire Alarm Bells manufactured for ZETA Alarms Ltd. UK
E&OE
Ref: IS/3500016/ZETA iss 1
www.zeta-alarms.co.uk
Allen/Hex bolt
INSTALLATION INSTRUCTIONS
Indoor Series,
150mm (6 inch) and 200mm (8 inch)
Fire Alarm Bell, Type A
Please ensure that the following instructions are
read carefully prior to installation.
1. Bells should be positioned a minimum of 2.4m
above the floor, in the vertical plane.
2. Remove gong by unscrewing allen/hex bolt.
3. Ensuring that the terminals are at the top of the
unit, feed field wiring through the base. Base
can be mounted either onto a flush or surface
mounted BESA, single gang installation box or
directly onto the wall. A knockout is provided at
the top of the base for surface wiring. (Fig 2/3)
4.
2
Connect wiring (max 2.5mm ) to terminals (Fig
1) observing polarity. Dress wires to avoid
touching the gong.
5. Correctly align gong on base and replace
allen/hex bolt to secure.
Fig 2: Semi-Flush Installation
Gong
Mounting
Screw
Please Note: Care should be taken to
avoid damage to the striker mechanism
BESA Box
or single gang
installation
box
Base
Knock-out for
surface wiring
Fig 3: Basic Mechanism and Gongs
150 or 200
Mounting holes are provided to suit either BESA single
gang installation boxes or for direct wall mounting.
60
53
BESA Box.
50.5
Mounting Holes (
Dimensions in mm)
+
(Polarised)
-
Base
IN INOUT OUT
Field Wiring
Max. 2.5mm
2
To next bell or
end-of-line
monitoring
device
From
control
panel
SPECIFICATION
Model ZTB6B/24 ZTB8B
Rated Voltage 20.4 to 27.6Vdc 20.4 to 27.6Vdc
Rated Current 11mA@24Vdc 17mA@24Vdc
Operating Temperature -
o
10 to +50 C
IP Rating (minimum) 23C 23C
Weight 410g 640g
Body Colour Red Red
-10 to +50 C
o
Fig 1: Wiring (front view) Observe Polarity
Note: For sound output data refer to Sound Output Data Sheet DS/BELLDATA/ZETA/ISS1
Fire Alarm Bells manufactured for ZETA Alarms Ltd. UK
E&OE
Ref: IS/3500016/ZETA iss 1
www.zeta-alarms.co.uk
Allen/Hex bolt
  • Page 1 1

Zeta ZTB6B Installation guide

Zeta
Brand
Zeta
Model
ZTB6B
Category
Fire protection
Type
Installation guide

Zeta ZTB6B is a fire alarm bell designed for indoor use. It has a rated voltage of 20.4 to 27.6Vdc and a rated current of 11mA@24Vdc. The bell has an operating temperature range of -10 to 50 degrees Celsius and an IP rating of 23C. It weighs 410g and has a red body color.

The Zeta ZTB6B is a versatile fire alarm bell that can be used in a variety of applications. It can be mounted on a flush or surface mounted BESA, single gang installation box, or directly onto the wall. A knockout is provided at the top of the base for surface wiring. The bell has a minimum mounting height of 2.4m above the floor.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents