ANKO 907 User manual

Brand: ANKO

Model: 907

Category: Heat pumps

Type: User manual

This manual is also suitable for

ANKO 907 is a general purpose pump for dispensing fluid-based products. It is a fixed speed pump with a simple on/off switch and a 6 foot power cord. The pump is self-priming and can run dry without damaging the motor or drive unit, though the tubing life will be reduced. The pump has a maximum working pressure of 40 PSI and a maximum suction lift of 29 feet (8.8m) with H₂O. The flow rate of the pump depends on the tubing used and can range from .4 to 987 ml/min. The pump is made of polypropylene housing and case using stainless steel fasteners.

1



MITYFLEXPERISTALTICPUMPS



PERISTALTICPUMP

OWNERSMANUAL



907&908SERIES



QUALITYMANAGEMENTSYSTEMREGISTERED

TOISO9001INTERNATIONALSTANDARDS



ANKO PRODUCTS INC. PUMP DIVISION

www.ankoproducts.com

2



ThankyouforpurchasinganAnkoMityflex®Peristalticpump.Wearesureyou

willbecompletelysatisfiedwithitsperformance.Shouldyouneedassistanceor

havequestionsregardingtheuseorinstallation,pleasevisitourwebsiteat

www.ankoproducts.com.



TABLEOFCONTENTS



WARRANTY 3

WARNING 3

RETURNANDREPAIR 3

PUMPFEATURES 4

PUMPINSTALLATION 4

FLOWCHARTS 5

ROLLERSELECTION 6

FUSEINSTALLATION/FANASSEMBLY 6

TUBINGINSTALLATION 7

TUBINGINSTALLATIONPROCEDUREA 7

TUBINGINSTALLATIONPROCEDUREB 8

TUBINGINSTALLATIONPROCEDUREC

ROLLERBRACKETASSEMBLY

9

10

ILLUSTRATIONOFPUMPHEAD

ASSEMBLY 11

REPLACEMENTPARTSLIST 11



Everyprecautionforaccuracyhasbeentakeninthepreparationofthismanual,however,ANKO

PRODUCTS,INC.neitherassumesresponsibilityforanyomissionsorerrorsthatmayappearnor

assumesliabilityforanydamagesthatresultfromtheuseoftheproductsinaccordancewiththe

informationcontainedinthismanual.



3



LIMITEDWARRANTY

ANKOPRODUCTS,INC.,warrantsequipmentofitsmanufactureandbearingitsidentification

tobefreefromdefectsinworkmanshipandmaterial.ANKOPRODUCTS,INC.’sliabilityunder

thiswarrantyextendsforaperiodofoneyearfromthedateofdeliveryfromourfactoryor

authorizeddistributor.Itislimitedtorepairingorreplacinganydeviceorpartofanydevice

whichisreturned,transportationprepaid,tothefactorywithinoneyearofdeliverytothe

originalpurchaser,andwhichisproventobedefectiveuponexaminationbyus.ANKO

PRODUCTS,INC.disclaimsallliabilityforconsequentialdamageofwhatevernature,damage

ofequipmentduringtransportation,damage,damageduetoimproperhandling,installation

orimproperoperationorfordeterminingsuitabilityfortheparticularuseintendedbya

purchaser.Replaceablepartsincludingtubessuppliedwiththeproductarenotcoveredby

anywarrantieseitherexpressedorimplied.ANKOPRODUCTS,INC.,makesnowarranties

eitherexpressorimplied,includingimpliedwarrantyormerchantability,otherthanthose

statedabove.Norepresentativehasauthoritytochangeormodifythiswarrantyinany

respect.Jurisdictionandvenueforenforcementofthiswarrantymaybebroughtonlyinthe

StateofFlorida.Thiswarrantgivesyouspecificlegalrights,andyoumayalsohaveother

rightswhichvaryfromstatetostate.



WARNING

ANKOPRODUCTS,INC.assumesnoresponsibilityorliabilityforchemicalcompatibilityofour

tubinginspecificapplications.ALWAYSpretesttubinginaccordancewithtubing

manufacturer’sspecifications.Tubingthatshowssignsofswelling,embrittlement,orother

deteriorationshouldnotbeused.



RETURNANDREPAIRREQUESTS

Pleasedirectallwarrantyrequeststotheappropriatedistributortheproductwaspurchased

from.



4



TheMITYFLEX®907and908modelsarefixedspeedgeneralpurposepumpsfordispensing

fluidbasedonproducts.The907ishousedinacaseandiscontrolledbyasimpleon/off

switchthatactivatesthepump.The908ismanufacturedwithazincplatedsteelbracketand

sixinch

leadwiresforconvenientassemblytoyourOEMapplication.



FEATURES

1. ELECTRICAL:115VAC,60HZ;OPTIONS:24to240VAC;50Hz,60Hz,or50/60Hz;12&

24VDC.The907alsoincludes;On/Offswitch;6footpowercord.

2. PRIMING:Unitisself‐primingandwillholdvacuumwhenoff.

3. OPERATION:Pumpcanrundrywithoutdamagingthemotorordriveunit,howeverthe

tubinglifewillbereduced.

4. CONSTRUCTION:Polypropylenehousingandcaseusingstainlesssteelfasteners.

5. MAX.HEADPRESSURE:Maximumworkingpressure40PSI.

6. MAX.SUCTIONLIFT:29feet(8.8m)withH₂O.

7. RATING:ACUnits‐100%ofcontinuousoperationat25°Cambient;DCUnits‐100%

continuousoperationat40°Cambient.

8. FLOWRATE:.4‐987ml/min.Dependingonthetubingused.(Seepage5).

9. FUSE:(907only)Locatedontheexteriorofthecase.(Seepage6forreplacement

procedureandpage5forfusetype).



INSTALLATIONINSTRUCTIONS

1. POWERREQUIREMENTS:Voltageandfrequencyofpowersupplymustbethesameas

shownonunit.

2. WIRINGCONNECTIONS:Allwiringandelectricalconnectionsmustcomplywithlocal

andnationalelectricalcodes.

3. MOUNTING:(907)Caseenclosedmodelhasrubberfeetandmountingflanges.This

enablesittobeusedonaflatsurfaceorwallmounted.Besurethatoneofthesetsof

ventholeshasplentyofairforcirculation.(908)MountingbracketsforOEM

applications.Besurethereisplentyofspaceforaircirculation.Donotallowtubingto

becrimped.

4. MOUNTINGLOCATION:Pump

shouldbeplacedinadrylocationwithadequatecooling

provided.Theambienttemperatureshouldnotexceed25°CforACunitsor40°Cfor

DCunits..



WARNING

Thisunitshouldnotbeusedinoutdoororhazardouslocations.



5



MODEL907FLOWRANGECHART

FLOWRATES(ml/min.)FUSE/ FAN

Tubing

ID

.062In

(1.6mm)

.125In

93.2mm)

.187In

(4.7mm)

.250In

(6.3mm)

 Fuse Fan

Unit#     

907‐002 .4 1.7 4 7  .5amp

907‐007 1.5 5.9 14 25  .5amp None

907‐014 3 12 28 48  1amp None

907‐023 5 19 46 81  1amp 12‐1115‐18‐00

907‐028 6 24 56 98  2amp 12‐1115‐18‐00

907‐036 8 30 72 126  1amp 12‐1115‐20‐00

907‐049 10 41 98 172  5amp 12‐1115‐25‐00

907‐058 12 49 116 208  2amp 12‐1115‐18‐00

907‐075 16 63 150 263  3amp 12‐1115‐18‐00

907‐108 23 91 216 378  3amp 12‐1116‐18‐00

907‐129 27 108 258 452  3amp 12‐1116‐18‐00

907‐172 36 144 344 602  3amp 12‐1116‐18‐00

907‐203 43 170 406 711  3amp 12‐1116‐18‐00

907‐282 60 237 564 987  5amp 12‐1116‐18‐00

Flowratebasedonpumpingwaterar25°Cand0PSIusing60durometerthermoplasticelastomertubing.



MODEL908FLOWRANGECHART

(ml/min.)

Tubing

ID

.062In

(1.6mm)

.125In

93.2mm)

.187In

(4.7mm)

.250In

(6.3mm)

 RPMS AMPS Fan

Unit#      

908‐002 .4 1.7 4 7  2 .37

908‐007 1.5 5.9 14 25  7 .37

908‐014 3 12 28 48  14 .37

908‐023 5 19 46 81  23 .42 12‐1116‐18‐00

908‐028 6 24 56 98  28 .75 12‐1116‐18‐00

908‐036 8 30 72 126  36 .90 12‐1116‐20‐00

908‐049 10 41 98 172  49 1.0 12‐1116‐25‐00

908‐058 12 49 116 208  58 1.2 12‐1116‐18‐00

908‐075 16 63 150 263  75 1.5 12‐1116‐18‐00

908‐108 23 91 216 378  108 1.9 12‐1115‐18‐00

908‐129 27 108 258 452  129 2.2 12‐1115‐18‐00

908‐172 36 144 344 602  172 2.2 12‐1115‐18‐00

908‐203 43 170 406 711  203 3.3/2.2 12‐1115‐18‐00

908‐282 60 237 564 987  282 3.3/2.2 12‐1115‐18‐00

Flowratebasedonpumpingwaterar25°Cand0PSIusing60durometerthermoplasticelastomertubing.



6



ROLLER/TUBINGSELECTION

UsethefollowingcolorcodedrollerswiththeappropriatetubingI.D.Yourunitisassembled

withblackrollers.Redrollersareincludedinyourtubingkit.Seeseparateinstructionsfor

rollerreplacementenclosedinyourtubekit.



Roller TubingID ML/Revolution

Black 1/4”(.250) 3.5

Black 3/16”(.187) 2.1

Red 1/8”(.125) 0.8

Red 1/16”* 0.21



*The1/16”IDtubingmustbeinsertedinto3/16”(.187)IDX3/8”(.375)ODtubing(sleeve)for

operationinpump.



FUSEINSTALLATION(907)

(Seepage4forfusetypeandpage10forfuseorderinginformation)

1. Disconnectpowertopump.

2. Removefourscrewsfromcasefront.

3. Carefullyremovecasecoverbeingsurenottopullwiresapart.

4. Laytheunitonaflatsurface.

5. Findfuseholderandpullapart.

6. Removeoldfuseandreplacewithnewfuse.

7. Replacecasecover.



FANASSEMBLY

(Seepage4forreplacementnumber)

Disconnectthepowerfromthepump.

Thefanispressedontotherotorshaft.Onall907caseunits,thefanispressedonwithmetal

clipawayfromthemotor.OnallOEM908units,thefanispressedonwiththemetalclip

towardthedoor.



7



TUBINGINSTALLATION

Inspectalltubingregularlyandreplaceifanysignofdeteriorationoccurs.Alwayswearsafety

glassesandprotectiveclothingwhenworkingwithchemicals.Seechartbelowforproper

tubinginstallationprocedureforyourunit.

*90_‐002through90_‐014 ProcedureA(below)

90_‐023through90_‐049 ProcedureAorB(page6or8)

90_‐058through90_‐282 ProcedureAorC(page6or9)

*WARNING:MODEL907‐002,907‐007,907‐014,908‐002,908‐007and908‐014GEARTRAINS

CANBEDAMAGEDIFDRIVESHAFTISROTATEDBYHANDFORTUBEINSERTION.

PROCEDUREA

 (Ifunitisnewstartwithstep#6.)



1. Disconnectpowertothepump.



2. Disconnectthesuctionanddischarge

tubingfromthepumptubing.



3. Removefourscrewsandpumpcover

frompumphead.



4. Pulloutoldpumptubinganddiscard.



5. Cleanrollerrace,removingand

particlesthatcoulddamagetubing.



6. Connectpowerandrunatslowest

speeduntilrollerbracketassemblyis

inpositionasshowninfigure1.



7. Pushnewtubingintoinletport,

anchoringtubingingrippers.Ifusing

a9”pieceoftube,11/2”shouldbe

extendedoutsideofinletport.(figure

2)



8. Continuetorunatslowestspeed

carefullyfeedingtubeintoraceasthe

rollersturn.(figure3)

(Keepfingersawayfromrollers).



9. Inserttubingintooutletport(figure

4)andreplacecover.



8



PROCEDUREB



Followsteps1‐5inprocedureA,then

continuewiththefollowing.



6. Usingextrabracket(figure1),rotate

rollerbracketassemblyuntilitisin

positionasinfigure2.(Besurepower

isdisconnected).



7. Pushnewtubingintoinletport,

anchoringthetubingingrippers(see

figure3).Ifusing9”pieceoftube,1

1/2”shouldbeextendedoutsideof

inletport.



8. Continuetorotatetherollerbracket

assemblyusingtheextrabracket,

whilepushingthetubingintothe

rollerrace.(figure4)



9. Insertthetubingintotheouterport

(figure5)andreplacethecoverand

screws.



9



PROCEDUREC

Withoutremovingthepumpcover,runtheentireunitat

highRPM.Pulltheoldtubingoutfromoutletportpump.

Installnewtubebyinsertingintoinletport;continue

feedingtube1/4”inatatimeallowingtheroller

assemblytopushtubingthrough.Whentubingishalf

wayaroundtherace,putyourfingerovertheinlethole

ofthetubeandcontinuetofeedtubing1/4”atatime,

thisshouldmakeinstallationeasier.Continueuntil

desiredtubingextensionisobtained.Rununitforabout

oneminute.



WARNING

ANKOPRODUCTS,INC.assumesnoresponsibilityorliabilityforchemicalcompatibilityofour

tubinginspecificapplications.ALWAYSpretesttubinginaccordancewithtubing

manufacture’sspecifications.Tubingthatshowssignsofswelling,embrittlement,orother

deteriorationshouldnotbeused.

ROLLERBRACKETASSEMBLYINSTRUCTIONS

10



ForRollerReplacement

(Aplasticrollerbracketassemblyissuppliedwithunitsrangingfrom2to108RPM.Noassemblyisrequiredforthe

plasticbracket.Ifnewrollersarerequiredanewassemblymustbeordered).

1. Toremovetherollerbracketassemblyfromthepump,useaflatheadscrewdriverand

pryopenbothsidesofthespringstotheedgeofthebracket.

2. Pulltherollerbracketassemblyofftheshaftholdingontotherollerareaofthebracket.

3. Holdingthetopandbottomofthebracket,slidethespringofftothesideandlaythe

assemblyonaflatsurface.Trynottoletitfallapartasyouwillneedtoputittogether

thesamewayitisnow.

4. Removethetopbracketandtherollers.

Ifarollerpincomesoutofitsrecess,replaceitatthistime.

6. Placethenewrollersonthepinsandreplacethetopbracket.Besurethattheflatinthe

innerholeofthetopbracketlinesupwiththeflatonthebottombracket.

7. Slidethespringfastenerbackoverthebracket.Donotsnapthespringtogether.

8. Matchingtherollerbracketflattotheoutputshaftflat,slidetherollerbracketassembly

downuntilitstopswithoutusingforce.

9. Snapthespringtogether.



Illustrationofthepumpassembly.





11



1‐ Fan 

2‐ Screw(1)8‐32x7/8”

3‐ Gearmotor

4‐ MountingBracket(908only)

5‐ PumpHousing 

6‐ Tube

7‐ Screws(4)10‐32x11/4”

8‐ *NylonWasher

9‐ RollerBracketAssembly

10‐ PumpCover

11‐ Screws(4)8‐32x5/8”

The908mountingbracketisreplacedwiththe907casecoveronthecasemodel.



ReplacementPartsList

Contactyourlocaldistributortoorder.Pleaserememberto includethecompletemodel

numberwhenyouplaceyourorderforreplacementparts.Forfanordersusethechartonpage

4forthepartnumber.

Item UnitNumber

PlasticRollerBracket(Red)………………………………………… RBA‐1718‐03‐25

PlasticRollerBracket(Black)……………………………………… RBA‐1718‐01‐25

BlackRollerBracketAssembly…………………………………… RB‐1212‐01‐00

RedRollerBracketAssembly…………………………………….. RB‐1212‐03‐00

PumpKit……………………………………………………………………. 907‐101‐0000‐10

Includeshousing,cover,w/bearing,fourscrews,andwasher.

TubeKit……………………………………………………………………… TU‐1124‐0000‐00

Includes9”ofeachofthefollowing:1/16”ID(inasleeve),1//8”ID,3/16”ID,and¼”IDthermoplasticelastomer

tubing.(Seechartonpage5fortubingandrollercompatibility).

Model907only:

Fuses.5amp(5/pack)……………………..FU‐1127‐00‐05

Fuses1amp(5/pack)……………………..FU‐1127‐01‐00

Fuses2amp(5/pack)……………………..FU‐1127‐02‐00

Fuses3amp(5/pack)……………………..FU‐1127‐03‐00

Fuses5amp(5/pack)……………………..FU‐1127‐05‐00

*Nowashernecessaryforunitsusinganallplasticrollerbracketassembly.(2to36RPM)

ANKO 907 User manual

Brand: ANKO

Model: 907

Category: Heat pumps

Type: User manual

This manual is also suitable for

Download PDF

report

ANKO 907 User manual

This manual is also suitable for

ANKO 907 User manual

Related papers

Other documents