Torqeedo 1269-00, a state-of-the-art electric outboard motor, offers a serene boating experience with its clean and efficient propulsion system. Designed for a wide range of boats, it delivers exceptional power and control, making it an ideal choice for both leisure and professional use. The motor's intuitive操控, coupled with its robust construction and advanced safety features, ensures a smooth and reliable operation on the water.
Torqeedo 1269-00, a state-of-the-art electric outboard motor, offers a serene boating experience with its clean and efficient propulsion system. Designed for a wide range of boats, it delivers exceptional power and control, making it an ideal choice for both leisure and professional use. The motor's intuitive操控, coupled with its robust construction and advanced safety features, ensures a smooth and reliable operation on the water.
Installation Drawing: I15
Version 1.0
Power cable connection
This installation drawing is an addition to the original operating instructions.
Read operating instructions before wiring.
678
H3000 mm
1
1
Power cable connection
Positive power cable
Negative power cable AC power cable
100-240 VAC/50-60 Hz
P
QB-
Positive charging cable
Negative charging cable
Optional equipment, see seperate sheet for wiring
1000 mm
2800 mm
1800 mm
I
K
L
M
2
AC 2000 mm
1300 mm
1300 mm
3
B+ B-
Installation Drawing: I15
Version 1.0
System ground connection
This installation drawing is an addition to the original operating instructions.
Read operating instructions before wiring.
2
System ground connection
Use for boats without common point for grounding
Use for boats with common point for grounding
W
In this conguration the motor fulllls the function of the grounding point
3
B+ B-
1
1
3
B+ B-
W
25 mm2 grounding cable
25 mm2 grounding cable
Installation Drawing: I15
Version 1.0
System ground connection
This installation drawing is an addition to the original operating instructions.
Read operating instructions before wiring.
3
System ground connection
In case the charger is permanently installed in the boat,
the charger housing or its AC PE and battery minus pole must be
connected to the common grounding point.
The AC connection requires specialist knowledge and may only be carried
out by qualied personnel.
If necessary, have the planning and installation carried out by a specialist.
NOTE! To charge the batteries in the boat, a land connection in the boat with galvanic
isolator or isolation transformer is required according to applicable
national requirements (e.g. DIN EN ISO 13297, ABYC E-11).
6
7
Connect the charger housing and the minus battery
pole to the common grounding point.
B-
3
B+
25 mm2 grounding cable
Installation Drawing: I15
Version 1.0
Data cable connection
This installation drawing is an addition to the original operating instructions.
Read operating instructions before wiring.
T
5000 mm
900 mm
50 mm
a
3
900 mm
50 mm
a
67 8
13
max. 900 mm
1500 mm
50 mm
4
4
4
a
5 5
dd
1500 mm
1000 mm
1000 mm/2000 mm
20
17
18
19
T
5000 mm
e
2600 mm
1
T
4
Data cable connection
8 pin data cable
5 pin data cable Backbone 5 pin data cable Bus system termination resistor
4 pin data cable
Backbone TorqLink, 8 pin data cable
e
Optional equipment
Installation Drawing: I15
Version 1.0
Bill of material/Legend/Information
This installation drawing is an addition to the original operating instructions.
Read operating instructions before wiring.
Pos. Item number Name Remarks
1 1269-00 Cruise 6.0 FP TorqLink
H, I, K,
L, M
Cable set with battery switch See picture for cable length
2 Power connector max. 175 A
b Backbone TorqLink cable 8-pin 5000 mm
3 2104-00 Power 48-5000 Select TorqLink-Battery in throttle menu!
a T-Cable 8-pin 900 mm/50 mm,
Do not extend!
not illus-
trated
+ Battery pole adapter
- Battery pole adapter
Not needed for your conguration
W System ground min. 25 mm2, not included
4 1949-00 Throttle Sidemount Sail
5 Throttle Display
22 000-00858 Gateway
U Gateway Power cable 1700 mm
b Backbone TorqLink cable 8-pin 5000 mm
d Data cable 4-pin 1500 mm
17 Emergency switch with cable 1000 mm
18 On/Off switch with cable 2000 mm
13 000-00876 TorqLink Terminator Bus termination resistor
a T-Cable 8-pin 900 mm/50 mm,
Do not extend!
4 1950-00 Throttle Sidemount
5 Throttle Display
22 000-00858 Gateway
U Gateway Power cable 1700 mm
b Backbone TorqLink cable 8-pin 5000 mm
d Data cable 4-pin 1500 mm
19 Kill switch with cable 1000 mm
20 Key switch
g Cable for key switch
6-Pin to 8-pin
1000 mm
13 000-00876 TorqLink Terminator Bus termination resistor
Pos. Item number Name Remarks
a T-Cable 8-pin 900 mm/50 mm,
Do not extend!
4 1951-00 Throttle Topmount
22 000-00858 Gateway
U Gateway Power cable 1700 mm
b Backbone TorqLink cable 8-pin 5000 mm
17 Emergency switch with cable 1000 mm
20 Key switch
g Cable for key switch
6-Pin to 8-pin
1000 mm
13 000-00876 TorqLink Terminator Bus termination resistor
a T-Cable 8-pin 900 mm/50 mm,
Do not extend!
6 2213-00 Charger Power 48 650 W, for AC charging while running use Fast
charger Power 48 2212-00;
Not compatible with solar charger 2218-00
P + DC charge cable 1300 mm; Do not extend!
Q - DC charge cable 1300 mm; Do not extend!
B+ + Battery pole 7,5 Nm
B- - Battery pole 7,5 Nm
AC AC power cable 2000 mm
a T-Cable 8-pin 900 mm/50 mm,
Do not extend!
5
Bill of material/Legend/Information
Installation Drawing: I15
Version 1.0
Bill of material/Legend/Information
This installation drawing is an addition to the original operating instructions.
Read operating instructions before wiring.
Pos. Item number Name Remarks
Optional equipment
7 2212-00 Fast charger Power 48 2900 W
P + DC charge cable 2400 mm; Do not extend!
Q - DC charge cable 2400 mm; Do not extend!
B+ + Battery pole 7,5 Nm
B- - Battery pole 7,5 Nm
AC AC power cable 1000 mm
a T-Cable 8-pin 900 mm/50 mm,
Do not extend!
8 2218-00 Solar charge controller for
Power 48-5000
For TorqLink system only!
Only as stand alone charger or in combination
with 2212-00 Fast charger Power 48!
P + Charge cable 1500 mm
Q - Charge cable 1500 mm
R + Input solar cable 150 mm
S - Input solar cable 150 mm
a T-Cable 8-pin 900 mm/50 mm,
Do not extend!
Connect the cruise motor and terminator to each end of the backbone.
The TorqLink bus system requires a terminator (terminating resistor) at both ends of the backbone in order
to function correctly.
One of the terminators is located in the „Terminator Single“, „Terminator Twin“, „Throttle 1918-00“, „ Throttle
1976-00“ , the other is built into the cruise motor. Therefore, when installing, make sure that the components
„Terminator“ and „Cruise motor“ are each connected to one end of the backbone.
The connection position of the remaining components on the backbone can be freely selected.
Keep the following points in mind when planning:
• An earthing point is required for your Torqeedo system. Take into account the connection and the
cables required for this in your planning. The required cable cross-sections can be found in the
section Tools, equipment and material.
• First determine and plan the installation positions of all components.
• Measure the required length of the TorqLink backbone.
• Measure the lengths of all required stub lines (cable connection between component
and TorqLink backbone).
• When planning, please note that TorqLink drop cables must not be extended. If necessary, plan
the TorqLink backbone so that the components can be connected through the
TorqLink drop cable without an extension. If necessary, extend the TorqLink backbone to connect
a component that is far away; you can nd corresponding extensions in our accessories
catalogue.
• Cables must be xed every 400 mm, plan attachment material. In places where fastening is not
possible, a scuff guard must be tted.
• Openly laid cables (e.g. inatable boat) must be protected with chang protection,
plan sufcient material.
• When planning, please note not to bundle power cables with data or antenna cables
(e.g. radios) for other loads.
• Observe the minimum bending radius of the cables when planning.
• If a second earthed onboard power system is available, ensure that both systems use a common
earthing point.
• Live parts must be tted or installed with protection against accidental contact; the necessary
installation space must be taken into account during the planning stage.
• Always connect batteries as the last component to the system to avoid short circuits and voltage
peaks.
• Do not extend drop cables, extend backbone if necessary.
• Protect plugs and contacts against contamination before installing them.
• Do not pull at the cables.
• Do not twist cables.
• Do not install cables in permanently wet areas such as bilges.
• Install cables free of chang and not around sharp edges, if necessary, attach chang protection.
• Maintain bending limits.
• Install plug connections free of tension and load.
Observe the minimum bending radius when laying all cables:
Torqeedo data cable 8 x diameter
Torqeedo power cable 8 x diameter
Earth cable see cable manufacturer's specica-
tions
Other power cables see cable manufacturer's specica-
tions
6
Bill of material/Legend/Information
Installation Drawing: I15
Version 1.0
Power cable connection
This installation drawing is an addition to the original operating instructions.
Read operating instructions before wiring.
7
Power cable connection
Positive power cable
Negative power cable AC power cable
Positive charging cable
Negative charging cable
100-240 VAC/50-60 Hz
P
Q
AC 1000 mm
2400 mm
2400 mm
7
3
B+ B-
Installation Drawing: I15
Version 1.0
Power cable connection
This installation drawing is an addition to the original operating instructions.
Read operating instructions before wiring.
8
8
Power cable connection
Positive power cable
Negative power cable AC power cable
Positive charging cable
Negative charging cable
R
S
Solar
P
Q
1500 mm
1500 mm
3
B+ B-
150 mm
150 mm
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Torqeedo 1269-00, a state-of-the-art electric outboard motor, offers a serene boating experience with its clean and efficient propulsion system. Designed for a wide range of boats, it delivers exceptional power and control, making it an ideal choice for both leisure and professional use. The motor's intuitive操控, coupled with its robust construction and advanced safety features, ensures a smooth and reliable operation on the water.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Torqeedo 1269-00 User manual
-
Torqeedo 1262-00 User manual
-
Torqeedo I45 Installation guide
-
-
-
-
-
-
-
Torqeedo Power 48-5000 Installation guide
Other documents
-
JLG T350 Service And Maintenance Manual
-
-
Smithco 7504 & 7506 Tournament Express Roller Owner's manual
-
Furuno GP330B User manual
-
Simrad GO XSE Installation guide
-
-
Xantrex XW4548-120/240-60 User manual
-
-
Raymarine SEATALK NG Installation Instructions Manual
-
