MEYER CROSS SF1788 Operating instructions

Type
Operating instructions

MEYER CROSS SF1788 is a semi-flush mount ceiling light designed for indoor use in dry locations. It features a stylish shade that can accommodate a single E26 (medium) base light bulb, with a maximum wattage of 60W for incandescent bulbs, 9W for LED bulbs, 13W for fluorescent (CFL) bulbs, or 9W for self-ballasted LED bulbs. The light fixture is easy to install and includes all necessary hardware for mounting on a standard ceiling junction box. With its versatile design, MEYER CROSS SF1788 is a great choice for adding warm and inviting light to any room in your home.

MEYER CROSS SF1788 is a semi-flush mount ceiling light designed for indoor use in dry locations. It features a stylish shade that can accommodate a single E26 (medium) base light bulb, with a maximum wattage of 60W for incandescent bulbs, 9W for LED bulbs, 13W for fluorescent (CFL) bulbs, or 9W for self-ballasted LED bulbs. The light fixture is easy to install and includes all necessary hardware for mounting on a standard ceiling junction box. With its versatile design, MEYER CROSS SF1788 is a great choice for adding warm and inviting light to any room in your home.

SEMI-FLUSH MOUNT CEILING LIGHT
Save these instructions
CARE INSTRUCTIONS:
• Turnlightoandallowbulbtocoolbeforecleaning.
• Carefullywipecleanwithasoft,dryclothorstaticduster.
• Alwaysavoidtheuseofharshchemicalsorabrasivecleanersastheymay
causedamagetothexture’snish
1
Made in China SF1786SF1787SF1788SF1789rev101822EFSME1A
Removethextureandthemountingpackagefromthebox
andmakesurethatnopartsaremissingbyreferencingthe
illustrationsontheinstallationinstructions.
IMPORTANT SAFETY INSTRUCTIONS:
• CAUTION –TURN OFF THE MAIN POWER AT THE
CIRCUIT BREAKER BEFORE INSTALLING THE FIXTURE,
IN ORDER TO PREVENT POSSIBLE SHOCK.
• CAUTION –If you feel you do not have enough electrical wiring experience contact a
qualiedlicensedelectricianforinstallationofyourlightingxture.
• Theseinstructionsareprovidedforyoursafety.Pleasereadcarefullyandcompletelybefore
beginningtheassemblyandinstallationofthislightingxture.
• Donotusetheelectriccordonly(withoutsteel/reinforcedcable)tosupporttheweightofthe
lightingxture.
• Thislightingxtureisintendedforindooruseonly,andindrylocations.
• Thislightingxtureisintendedforceilingmountonly,andconnectedonlyto3-wire,
single-phaseelectricalsupplysystemwithproperGroundwireorsystem.
• ForusewithE26(medium)baselightbulbsonly.
• Toavoidtheriskofre,donotexceedthemaximumwattageof60Wincandescentbulb,
or9WLEDbulb,or13Wuorescent(CFL)bulb,or9Wself-ballastedLEDbulb.
(Bulbsnotincluded)
WARNINGS:
• Toreducetheriskofre,electricalshock,orpersonalinjury:alwaysturnothislightingxture
andallowittocoolbeforeattemptingtoreplacethelightbulb.
• Donottouchlightbulbwhilextureisturnedon.
• Keepammablematerialsawayfromthislightingxture.
• Neverlookdirectlyatalitbulb.
2
1. Feed wires through the mounting
bracket (A).
2. Securely connect wires as shown
using wire connectors. Connect white
to white, black to black, and connect
the green or copper ground wire to the
mounting plate ground as shown.
3. Secure mounting bracket (A) to the
ceiling mount using long screws (B).
Required Supply Circuit: 120V, 60Hz
1/2 Inch (12.7 mm)
1/2 Inch (12.7 mm)
WHITE WHITE
BLACK BLACK
GREEN/COPPER GREEN/COPPER
1/2 Inch (12.7 mm)
1/2 Inch (12.7 mm)
1/2 Inch (12.7 mm)
!
4. Secure ceiling cover (C) to the mounting
bracket (A) using short screws (D).
6. Install the speciedlightbulb.
5. Lift the Lampshade (E) into place
and secure by screwing on the
Socket Collar (F).
PRE-ASSEMBLY:
Carefully remove all parts and hardware from carton, along with any protective plastic
packaging. The lampshade may be covered with a plastic lm that should be removed
before use.
Do not discard any contents until after assembly is complete to avoid accidentally
discarding small parts or hardware.
C
E
F
A
B
D
DO NOT EXCEED THE SPECIFIED WATTAGE.
Picturedwith:
ST19/ST64LEDL
E26(medium)base
(Notincluded)
PLAFONNIER À MONTAGE SEMI-FLUSH
Conservez ces instructions
INSTRUCTIONS D’ENTRETIEN :
• Éteindrelalumièreetlaisserl’ampoulerefroidiravantdenettoyer.
• Essuyeravecprécautionavecunchiondouxsecouunplumeauantistatique.
• Éviteztoujoursd’utiliserdesproduitschimiquesfortsouagentsnettoyantsabrasifs,
carilspourrontendommagerlanitionduluminaire.
3
FabriquéenChine
CONSIGNES DE SÉCURITÉ ESSENTIELLES :
• ATTENTION – SECTIONNER L’ALIMENTATION AU NIVEAU
DU DISJONCTEUR AVANT D’INSTALLER LE LUMINAIRE,
AFIN D’ÉCARTER LE RISQUE DE CHOC ÉLECTRIQUE.
• ATTENTION–Sivouspenseznepasavoirsusammentdecompétences
decâblageélectrique,faitesinstallerleluminaireparunélectricienagréé.
• Cesconsignessontfourniesauxnsdevotresécurité.Veuillezleslireattentivementet
aucompletavantdecommencerl’assemblageetlamiseenplacedeceluminaire.
• Nepasutiliserlecordonélectriqueseul(sanscâblederenfortenacier)poursoutenirle
poidsduluminaire.
• Celuminaireestconçuexclusivementpouruneutilisationàl’intérieuretdansdesendroits
secs.
• Celuminaireestconçupourêtremontéauplafondseulementetraccordéàuncircuit
électriquemonophaséà3conducteursaveccircuitouconducteurdeterrecorrect.
• PourutilisationuniquementaveclesampoulesavecbasedeE26(moyenne).
• Pouréliminertoutrisqued’incendie,évitezdedépasserlapuissancemaximaleprescrited’une
ampouleàincandescencede60W,oud’uneampouleDÉLde9W,oud’uneampoule
uorescente(CFL)de13W,oud’uneampouleDÉLàballastintégréde9W.
(Ampoulesnonincluses)
AVERTISSEMENTS :
• Pourréduirelerisqued’incendie,dechocélectriqueoudeblessurecorporelle,toujours
éteindreceluminaireetlelaisserrefroidiravantdetenterdechangerl’ampoule.
• Évitezdetoucherl’ampoulependantqueleluminaireestsoustension.
• Gardeztoutematièreinammableéloignéedeceluminaire.
• Éviteztoujoursderegarderdirectementuneampouleallumée.
Sortirleluminaireetlenécessairedexationdel’emballage
etconsulterlesillustrationsdanslesinstructionsd’installation
pourvérierqu’ilnemanqueaucunepièce.
4
1. Faites passer les ls à travers la plaque
de xation (A).
2. Raccordez solidement les ls à l’aide de
connecteurs à ls tel que l’illustre la gure
ci-contre. Raccordez blanc à blanc, et
noir à noir, puis raccordez le l de masse
vert ou cuivre à la mise à la masse de la
plaque de xation tel que l’illustre la gure
ci-contre.
3. Fixez la plaque de xation (A) au
plafond à l’aide de vis longues (B).
4. Mettez en place la couverture de plafond
(C) à la plaque de xation (A) en utilisant
les vis courtes (D).
6. Installez l’ampoule spéciée.
ÉVITEZ DE DÉPASSER LA PUISSANCE
MAXIMALE SPÉCIFIÉE
Surlaphotoavec:
ST19/ST64DÉL
BaseE26(moyenne)
(Noninclus)
5. Soulevez l’abat-jour (E) et xez-le en
vissant la bague à douille (F).
Circuit d’alimentation requis : 120 V, 60 Hz
1/2 Inch (12.7 mm)
12,7 mm (½ pouce)
1/2 Inch (12.7 mm)
BLANC BLANC
NOIR NOIR
VERT/CUIVRE VERT/CUIVRE
1/2 Inch (12.7 mm)
1/2 Inch (12.7 mm)
1/2 Inch (12.7 mm)
!
PRÉASSEMBLAGE :
Retirez soigneusement de la boîte toutes les pièces, toute la quincaillerie, et tout
emballage de plastique protecteur.
Ne mettez aucun élément de contenu au rebut avant de terminer l’assemblage au complet,
an d’éviter de jeter accidentellement de petites pièces ou un élément de quincaillerie.
C
E
F
A
B
D
LÁMPARA DE TECHO DE SEMI EMPOTRADO
Guarde estas instrucciones
INSTRUCCIONES DE CUIDADO:
• Desenchufelalámparaantesdelimpiarla.
• Limpieconunpañosuaveysecooconunpañoparaestática.
• Evitesiempreelusodelimpiadoresquímicosásperosoabrasivos,yaquepuedendañar
elacabadodelaccesorio.
5
Hecho en China
Extraigaelartefactoyelpaquetedemontajedelacajay
asegúresedequenofaltenpiezasvericandoconlas
ilustracionesdelasinstruccionesdemontaje.
INSTRUCCIONES IMPORTANTES DE SEGURIDAD:
• PRECAUCIÓN - ANTES DE INSTALAR EL ARTEFACTO CORTE
LA ALIMENTACIÓN ELÉCTRICA PRINCIPAL EN EL DISYUNTOR
PARA EVITAR POSIBLES DESCARGAS ELÉCTRICAS.
• PRECAUCIÓN-Sicreequenotienesucienteexperienciaconcableseléctricos,
hagainstalarelartefactoporunelectricistacualicadoymatriculado.
• Estasinstruccionesseproporcionanparasuseguridad.Léalascuidadosamenteypor
completoantesdecomenzaraensamblareinstalarestalámpara.
• Noutilicesoloelcableeléctrico(sinunalambredeacero/reforzado)parasostenerelpeso
delalámpara.
• Estalámparaestádestinadaaserutilizadasoloeninterioresyenlugaressecos.
• Estalámparaestádestinadaasermontadaenelcielorrasoúnicamenteyconectadaaun
sistemadealimentacióneléctricade3cables,monofásica,conunsistemaocablede
descargaatierraadecuado.
• ParautilizarconbombillasconunabaseE26(mediano)solo.
• Paraevitarelriesgodeincendios,noexcedaelvatajemáximodeunabombilla
de60Wincandescente
,LEDde9W,uorescente(CFL)de13W,
oLEDbalastoincorporadode9W.(Bombillasnoincluidas)
ADVERTENCIAS:
• Parareducirelriesgodeincendio,electrochoqueolesionespersonales:siempreapaguey
desenchufeestalámparaydéjelaenfriarantesdeintentarreemplazarlabombilla.
• Notoquelabombillamientraslalámparaestáencendida.
• Mantengalosmaterialesinamableslejosdelalámpara.
• Nuncamiredirectamenteaunabombillaencendida.
6
1. Pase los cables a través de la placa de montaje (A).
2. Conecte los cables en forma segura con
conectores para cable, tal como se muestra.
Conecte blanco con blanco, negro con negro
y el cable verde o cobre de descarga a tierra
a la descarga a tierra de la placa de montaje
tal como se muestra.
3. Asegure la placa de montaje (A) al
techo con tornillos largos (B).
4. Instale la cubierta del techo (C) a la placa de
montaje (A) usando los tornillos cortos (D).
6. Instale la bombilla especicada.
5. Levante la pantalla (E) en su lugar y asegúrela
atornillando el anillo de enchufe (F).
Circuito de alimentación necesario: 120V, 60Hz
1/2 Inch (12.7 mm)
1/2 pulgada (12.7 mm)
BLANCO BLANCO
NEGRO NEGRO
VERDE/COBRE VERDE/COBRE
1/2 Inch (12.7 mm)
1/2 Inch (12.7 mm)
1/2 Inch (12.7 mm)
!
ANTES DEL ENSAMBLADO:
Retire con cuidado todas las piezas y herramientas de la caja, junto con todo el
envoltorio plástico protector.
No deseche nada hasta después de haber terminado de ensamblar para evitar botar por
accidente piezas pequeñas o herramientas.
C
E
F
A
B
D
Mostrado:
ST64LED
BasedeE26(mediano)
(Noincluido)
NO EXCEDA EL VATAJE ESPECIFICADO
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

MEYER CROSS SF1788 Operating instructions

Type
Operating instructions

MEYER CROSS SF1788 is a semi-flush mount ceiling light designed for indoor use in dry locations. It features a stylish shade that can accommodate a single E26 (medium) base light bulb, with a maximum wattage of 60W for incandescent bulbs, 9W for LED bulbs, 13W for fluorescent (CFL) bulbs, or 9W for self-ballasted LED bulbs. The light fixture is easy to install and includes all necessary hardware for mounting on a standard ceiling junction box. With its versatile design, MEYER CROSS SF1788 is a great choice for adding warm and inviting light to any room in your home.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI