Riva RC3102HD-5211 Installation guide

Brand
Riva
Model
RC3102HD-5211
Category
Camera accessories
Type
Installation guide

This manual is also suitable for

1
www.rivatech.de
RC3102HD-5211
Installation Guide
2
01A.06
www.rivatech.de
INFORMATION TO USER
CAUTION
RISK OF ELECTRIC SHOCK,
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
CONTACT QUALIFIED SERVICE PERSONNEL FOR INTERNAL
PARTS.
This symbol is intended to alert the user the presence of un-
insulated “dangerous voltage” within the product’s enclosure,
which may be sufficient magnitude to constitute a electric shock
risk to persons.
This symbol is intended to alert the user the presence of
important operating and maintenance (servicing) instructions
within the guide manual.
!
!
3
01A.06
www.rivatech.de
Table of Contents
1. FEATURES ................................................................................ 4
2. PACKAGE CONTENTS ................................................................. 5
3. PART NAMES ........................................................................... 6
4. INSTALLATION .......................................................................... 8
4.1. Installation Template ............................Fehler! Textmarke nicht definiert.
4.2. Setting the Lens Position .............................................................. 10
4.3. Setting the Image Attribute ........................................................... 11
5. CONNECTIONS ........................................................................ 11
6. CONFIGURATION...................................................................... 15
6.1.Set up network environment .......................................................... 15
6.1.1. Generic IP Environment .......................................................... 15
6.1.2. Custom IP Environment .......................................................... 16
6.2. View video on web page ............................................................... 17
6.2.1. View video using IPAdmin Tool ................................................. 19
6.3. Reset ........................................................................................ 20
6.4. Factory Default ........................................................................... 20
APPENDIX (A): SPECIFICATIONS ..................................................... 21
Summary .......................................................................................... 21
Electrical Characteristics ..................................................................... 22
Environment Condition ........................................................................ 22
Mechanical Condition .......................................................................... 22
APPENDIX (B): POWER OVER ETHERNET ......................................... 23
PoE compatibility ................................................................................ 23
Power classification ............................................................................ 23
APPENDIX (C): DIMENSIONS .......................................................... 24
APPENDIX (D): HEXADECIMAL-DECIMAL CONVERSION TABLE ............. 25
REVISION HISTORY ....................................................................... 26
4
1.FEATURES
Camera
Full HD indoor dome IP camera (Vandal proof)
High quality compression in real time streaming
1/2.7” High Quality CMOS Image Sensor
True Day / Night (ICR)
Improved color rolling suppression
Streaming
Dual streaming mode (such as different codec/resolution/bit rate and so
on.)
*
Burnt-in text
Unicast/Multicast
Video/Audio
Video compression: H.264, MJPEG, up to 30FPS@1080p*
Audio compression: G.711(µLaw, aLaw)/PCM
Analog video output (for installation only)
Video motion detection
Two-way mono audio
Network
RTSP/ HTTP protocol
10/100 Base-T Ethernet
Additional Features
Micro SD card
PoE supported
Built-in Video Content Analysis
SDK (Software Development Kit) provided
* When VCA is activated, frame rate is limit to max15fps@1080p. Limitations are
based on V.1.5.0 firmware release and could be changed without notice.
5
2. PACKAGE CONTENTS
The package contains main camera, DC power adaptor, DC jack cable, 9-pin and 2-pin
terminal blocks, video-out cable, screws, anchors, hex wrench driver, and clamping
cores. Unpack carefully and handle the equipment with care.
Camera
DC power adaptor
DC Jack Cable
9-pin and 2-pin terminal block
Video out cable
Screws and anchors
Quick installation guide
Hex wrench driver
Clamping core
To prevent electromagnetic interference
The above contents are subject to change without prior notice.
Note
i
6
3. PART NAMES
1. PAL/NTSC button
The initial factory version setting is free from PAL or NTSC. Push the button once to
set as PAL format. Push the button twice to set as NTSC. Push the button one more
time to return to no video output mode. Please note that the analog video signal is
only 3 minutes present and go back automatically to none video output mode (only
installation process).
2. Reset button
The reset button can be used for restarting the device or resetting it to Factory
Default. Refer to
6.3. Reset
and
6.4. Factory Default
for more details.
* Models herein and their
appearance are subject to change
without any prior notice.
*This button is
located under PCB.
7
3. Video output, audio and IO terminal connector
A 9-pin terminal block is included in the device package. Connect this terminal block
into this connector for cable connection of video output, audio input/output and digital
input/output. Refer to section
5. Connections
for more details. Video out is used
only for installation and works for 3 minutes when PAL/NTSC button is pushed.
4. LAN connector
This is a RJ45 LAN connector for 10/100 Base-T Ethernet.
5. Micro SD card slot
It is a memory card slot for external storage.
6. Power Adaptor Connector (DC 12V)
The camera requires a DC 12V 1A power adapter.
8
4.INSTALLATION
To prevent products from damaging, place the camera on
stable and non-vibrating surfaces If the stability is in doubt,
consult with safety personnel for reinforcements, and then
proceed with the installation.
Caution
!
1) Place the installation template
(paper) that is included in the
package on the desired installation
surface.
2) Drill three holes in correct
positions based on the template
paper, and insert anchor blocks into
the holes.
3) Place the camera body and match
three alignment holes with three
anchor blocks. Fasten the camera
with screws.
4) Connect all the required cables to
the camera.
5) Adjust the lens position. Detailed
information can be found in
4.2.
Setting the Lens Position
.
6) Place the dome cover on the main
body of the camera. Dome cover has
three alignment holes that match
camera body’s alignment holes.
7) Once properly placed, insert
alignment screws into the three
holes of the body and fasten them
up.
9
4.1. Installation Template
Installation template image’s size scale in this installation guide is
not 1:1.
The correct-size template design paper can be found inside the
package separately.
Caution
!
10
4.2. Setting the Lens Position
Instruction below describes how to set the lens positions and manually adjust zoom
and focus.
1) Remove the dome cover.
2) Adjust the lens to the desired position by manually moving its reinforced body,
upper lens shell, or horizontal platform in the following directions.
3) Connect to the web page of the device to see its real-time image. Refer to
step
6.
Configuration
for details about using its web page.
5) Unscrewing the focus puller in counterclockwise rotation will allow users to adjust
the lens focus position. After the setting, tighten up the focus puller again by turning it
clockwise.
Zoom puller
Focus puller
C. Tilt the lens with
horizontal platform
A. Rotate the lens
with upper lens shell
B. Pan the lens with
reinforced lower body
4) Unscrewing the zoom puller in
counterclockwise rotation will allow
users to adjust the lens zoom position.
After the setting, tighten up the zoom
puller again by turning it clockwise.
11
4.3. Setting the Image Attribute
Through the camera’s webpage, users can configure image settings.
The camera image’s brightness, contrast, saturation and sharpness are adjustable
through the image settings. (Setup > Video & Audio > Camera).
5.CONNECTIONS
1. Audio input/output
The camera has a mono audio input and a mono audio output. Due to low audio output
power, an amplified speaker is recommended for enhanced sound (Do not connect a
headphone or earphone directly to the camera).
Mic
Amp Speaker
ETHERNET
MICRO SD
DC12V
DO
DI
1
OutOut
1
VIDEO
C C
In
AUDIO
+
Reset
SW1 SW2 SW3
SW5 SW6
N / A N / A
N / A N / A
SW1
SW2
SW3
SW4
SW5
SW6
ETHERNET
MICRO SD
DC12V
DO
DI
1
OutOut
1
VIDEO
C C
In
AUDIO
+
Reset
SW1 SW2 SW3
SW5 SW6
N / A N / A
N / A N / A
SW1
SW2
SW3
SW4
SW5
SW6
12
2. Sensor (DI) connection
The camera provides 1 channel D/I. It can be connected to either a voltage type
sensor or a relay type sensor as the following figures. Settings can be done through
the camera’s webpage.
Input voltage range: 0VDC minimum to 5VDC maximum, Max 50mA
Input voltage threshold: 1.5V
Do not exceed the maximum input voltage or relay rate.
Caution
!
+5V
DI
COM
DI
COM
+
-
Relay Type
Voltage Type
+
-
Output of
Sensor
Output of
Sensor
Internal
Internal
+
-
13
3. Alarm (DO) connection
Only the relay type is supported.
Relay Rating: Max 24VDC 50mA
Do not exceed the maximum relay rating.
4. Video output
The camera provides 1 video out. Please note that the analog video signal is only 3
minutes present after pushing the PAL/NTSC button and go back automatically to
none video output mode (only installation process).
Caution
!
Video
GND
Red
Black
DO
COM
Relay Type
Device
Internal
14
5. LAN connection
This is a RJ45 LAN connector for 10/100 Base-T Ethernet. Connect a LAN cable.
When the device is powered-on, both LEDs blink for a second. Then the orange LED
turns on initially for a while, and eventually green LED turns on when the device is
ready.
6. 12V DC Power
A 12 DC power connector is required for this device.
12V
Red
Black
LED LED
Green Orange
15
6.CONFIGURATION
6.1.Set up network environment
The default IP address of the device is 192.168.XXX.XXX. Users can identify the IP
address of the device from converting the MAC address’s hexadecimal numbers, which
is attached to the device. Be sure that the device and PC are on a same area network
before running the installation.
IP address : 192.168.xxx.xxx
Subnet mask: 255.255.0.0
6.1.1. Generic IP Environment
In case of generic private network environment where IP address 192.168.XXX.XXX
are used, users may view the live streaming images on a web page using the device’s
default IP address:
1. Convert the device’s MAC address to the IP address. Refer to the Hexadecimal-
Decimal Conversion Chart at the end of the manual.
(The MAC address of the device is attached on the side or bottom of the device.)
2. Start the Microsoft® Internet Explorer web browser and enter the address of the
device.
3. Web streaming and device configurations are supported through ActiveX program.
When the ActiveX installation window appears, authorize and install the ActiveX.
MAC address = 00-13-23-01-14-B1 → IP address = 192.168.20.177
Convert the last two set of hexadecimal numbers to decimal numbers.
16
6.1.2. Custom IP Environment
IPAdminTool and the manual are provided on USB stick or can download from
www.rivatech.de homepage.
IPAdminTool is a management tool, which automatically scans all of the network
products for users to perform administrative tasks, which includes network
configurations, firmware update, device reboot, and device organizations.
To modify the device’s default IP address for customized network area;
1. Find the device from the IPAdminTool’s list and highlight the device’s name.
2. Right-click the mouse and select “IP Address”; IP Setup window appears.
PC environment Info
Give new unique IP address in
last two sets and mirror other
information in other boxes
17
3. In the IP Setup’s window, information under ‘Local Network information’ displays the
user/PC’s network area information. Those information need to be incorporated to
the IP Address, Subnet Mask, Gateway, and DNS boxes, except the last 2 sets of
IP Address, which are to be the unique numbers for the device. Refer to the image
above for the setting
4. Click ‘Setup’ to complete the modification. When the dialog box appears to request
user name and password, enter the default value for the administrator account
(case-sensitive) as below:
ID:
root
Password:
pass
6.2. View video on web page
Type the proper IP address to view the live streaming images through a web browser.
The default username and password is
root / pass
.
1. The browser asks to install the ActiveX. Click Allow.
2. Setup.exe installation link or pop-up window appears, depends on Microsoft®
Internet Explorer version. Proceed with rest of setup installation.
18
Caution
!
3. Follow the instructions of the dialog boxes and complete the installation. Once the
installation is complete, start the web browser again and check if video stream is
displayed in the main view frame.
If “
This software requires the Microsoft XML Parser V6 or higher.
Please download MSXML6 from the Microsoft website to continue.
Error code: Cannot create XMLDOMDocument.
” message appears,
download and install the Microsoft Core XML Services (MSXML)
19
Caution
!
6.2.1. View video using IPAdmin Tool
IPAdminTool automatically searches all activated network encoders and IP cameras
and shows the product name, IP address, MAC address and etc. IPAdminTool is
provided on USB stick or can download from www.rivatech.de homepage.
1. From the IPAdminTool’s product list, select the device by highlighting it.
2. Right-click the mouse and select Web view
3. The system’s default web browser opens the device’s address. Please take care
that the default system web browser is Microsoft® Internet Explorer to support
ActiveX plug-in.
Whether directly accessing the streaming video through
typing IP address on a web page or taking steps through
IPAdminTool, the ActiveX is needed to be installed for the
Microsoft® Internet Explorer to have the complete
configuration privileges.
20
6.3. Reset
1. Push the Reset button and hold for 1~2 seconds.
2. Wait for the system to reboot.
6.4. Factory Default
If you reset your device to the factory default setting, all parameters including the IP
address will be initialized.
To proceed back to the Factory Default reset:
1. While the device is on, press reset button and hold.
2. Release the Reset button after about 5 seconds when green LED blinks at rate of
200ms.
3. Wait for the system to reboot
The factory default settings can be inferred as follows:
More Information
To learn more about using other features of your devices, refer to the manuals as
“Web Interface Manual” or “VCAsys_Online_Help”, which is available on USB stick or on
www.rivatech.de homepage.
IP address: 192.168.xx.yy
Network mask: 255.255.0.0
Gateway: 192.168.0.1
User ID: root
Password: pass
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26

Riva RC3102HD-5211 Installation guide

Brand
Riva
Model
RC3102HD-5211
Category
Camera accessories
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents