INSTRUCTION MANUAL
Read and understand all of the instructions and
safety information in this manual before operating or
servicing this tool.
Register this product at www.greenlee.com
52058009 REV 1
LDD-216 Drill/Driver and
LHD-216 Hammer Drill/Driver
21.6V Cordless 1/2"
Power Tools
© 2012 Greenlee Textron Inc. 7/12
Español................23
Français ..............45
2
Table of Contents
Description ................................................................ 2
Safety ........................................................................ 2
Purpose of this Manual .............................................. 2
Important Safety Information .................................. 3–7
General Safety Rules ........................................ 3–4
Specific Safety Rules ........................................... 5
For Battery Charger and Battery Pack ...............6-7
Identification .............................................................. 8
Specifications ............................................................ 9
Operation—Power Tool ......................................10–14
Bit Installation .................................................... 11
Support Handle .................................................. 11
Variable Speed Trigger Operation ....................... 11
Forward/Reverse Switch Operation .................... 12
Clutch Torque Setting ......................................... 12
Speed Selection ................................................. 13
Bit-locking Function ........................................... 13
Control Panel ................................................13-14
Recommended Grip ........................................... 14
Operation—Battery Pack ....................................15-16
Attaching or Removing Battery Pack .................. 16
Appropriate Use of Li-ion Battery Pack ............... 16
Operation—Battery Charger ...............................17-19
Charging Li-ion Battery Pack .............................. 18
Appropriate Use of Battery Charger .................... 19
Lamp Indications ............................................... 19
Maintenance ............................................................ 20
Warranty .................................................................. 21
Description
The Greenlee LDD-216 Drill/Driver and LHD-216
Hammer Drill/Driver 21.6V Cordless 1/2" Power Tools
are intended to drill multiple sizes of holes using
various 1/16" to 1/2" shanks into different types
of materials such as wood, sheet metal, aluminum,
drywall, and other materials. The LHD-216 can also
drill holes in soft concrete.
These tools can also be used for driving screws, bolts,
nuts, and other fastening devices. Consult the other
sections of this manual for proper selection of bits,
torques, speeds, and safety measures for the various
applications.
Safety
Safety is essential in the use and maintenance of
Greenlee tools and equipment. This instruction manual
and any markings on the tool provide information for
avoiding hazards and unsafe practices related to the
use of this tool. Observe all of the safety information
provided.
Purpose of this Manual
This manual is intended to familiarize all personnel
with the safe operation and maintenance procedures
for the following Greenlee tools:
• LDD-216 21.6V Cordless 1/2"
Drill/Driver Power Tool
• LHD-216 21.6V Cordless 1/2"
Hammer Drill/Driver Power Tool
Keep this manual available to all personnel.
Replacement manuals are available upon request at no
charge at www.greenlee.com.
Do not discard this product or throw away!
For recycling information, go to
www.greenlee.com.
KEEP THIS MANUAL
All specifications are nominal and may change as design
improvements occur. Greenlee Textron Inc. shall not
be liable for damages resulting from misapplication or
misuse of its products.
3
LDD-216 • LHD-216
Important Safety Information
SAFETY ALERT
SYMBOL
This symbol is used to call your attention to
hazards or unsafe practices which could result
in an injury or property damage. The signal
word, defined below, indicates the severity of
the hazard. The message after the signal word
provides information for preventing or avoiding
the hazard.
Immediate hazards which, if not avoided, WILL
result in severe injury or death.
Hazards which, if not avoided, COULD result in
severe injury or death.
Hazards or unsafe practices which, if not avoided,
MAY result in injury or property damage.
GENERAL SAFETY RULES
Read all instructions.
Failure to follow all instructions
listed below may result in electric
shock, fire and/or serious injury.
The term “power tool” in all of the
warnings listed below refers to your
mains operated (corded) power
tool and battery operated (cordless)
power tool.
SAVE THESE INSTRUCTIONS
Work Area Safety
1. Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
2. Do not operate power tools in explosive atmo-
spheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
3. Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
Electrical Safety
1. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
2. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges
and refrigerators. There is an increased risk of
electric shock if your body is earthed or grounded.
3. Do not expose power tools to rain or wet con-
ditions. Water entering a power tool will increase
the risk of electric shock.
4. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
5. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
Personal Safety
1. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or medi-
cation. A moment of inattention while operating
power tools may result in personal injury.
2. Use safety equipment. Always wear eye
protection. Safety equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing pro-
tection used for appropriate conditions will reduce
personal injuries.
4
Important Safety Information
3. Avoid accidental starting. Ensure the switch is
in the off position before plugging in. Carrying
power tools with your finger on the switch or
plugging in the power tools that have the switch
on invites accidents.
4. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
5. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
6. Dress properly. Do not wear loose clothing or
jewelry. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewelry
or long hair can be caught in moving parts.
7. If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
these devices can reduce dust related hazards.
Power Tool Use and Care
1. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
2. Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.
3. Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
4. Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
5. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tools operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
6. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
7. Use the power tool, accessories and tool bits
etc. in accordance with these instructions and
in the manner intended for the particular type
of power tool, taking into account the working
conditions and the work to be performed.
Use of the power tool for operations different
from those intended could result in a hazardous
situation.
Battery Tool Use and Care
1. Ensure the switch is in the off position before
inserting battery pack. Inserting battery pack
into power tools that have the switch on invites
accidents.
2. Recharge only with the charger specified by
the manufacturer. A charger that is suitable for
one type of battery pack may create a risk of fire
when used with another battery pack.
3. Use power tools only with specifically desig-
nated battery packs. Use of any other battery
packs may create a risk of injury and fire.
4. When battery pack is not in use, keep it away
from other metal objects like paper clips,
coins, keys, nails, screws, or other small metal
objects that can make a connection from one
terminal to another. Shorting the battery termi-
nals together may cause burns, or a fire.
5. Under abusive conditions, liquid may be
ejected from battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irrita-
tion or burns.
Service
1. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of power
tool is maintained.
5
LDD-216 • LHD-216
Important Safety Information
SPECIFIC SAFETY RULES
1. Wear ear protectors. Exposure to noise can
cause hearing loss.
2. Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
3. Hold power tools by insulated gripping
surfaces when performing an operation where
the cutting tool may contact hidden wiring.
Contact with a “live” wire will make exposed
metal parts of the tool “live” and shock the
operator.
4. Be aware that this tool is always in an operating
condition, since it does not have to be plugged
into an electrical outlet.
5. If the bit becomes jammed, immediately turn the
trigger switch off to prevent an overload which
can damage the battery pack or motor. Use
reverse motion to loosen jammed bits.
6. Do not operate the Forward/Reverse lever when
the trigger switch is on. The battery will discharge
rapidly and damage to the unit may occur.
7. When storing or carrying the tool, set the Forward/
Reverse lever to the center position (switch lock).
8. Do not strain the tool by holding the speed control
trigger halfway (speed control mode) so that the
motor stops. The protection circuit will activate
and may prevent speed control operation. If this
happens, release the speed control trigger and
squeeze again for normal operation.
9. Be careful not to get dust inside the chuck.
10. Do not touch the rotating parts to avoid injury.
11. Do not use the tool continuously for a long period
of time. Stop using the tool from time to time to
avoid temperature rise and heat overload of the
motor.
12. Do not drop the tool.
13. Wear dust mask, if the work causes dust.
14. During charging, the charger may become slightly
warm. This is normal. Do NOT charge the battery
for a long period.
Symbol Explanation
V Volts
Direct current (DC)
no No load speed
Drill setting
Rotation with hammering
(LHD-216 only)
rpm Revolutions per minute
Some dust created by power sanding, sawing,
grinding, drilling, and other construction activities
contains chemicals known to the State of California
to cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks and cement and
other masonry products
• Arsenic and chromium from chemically-treated
lumber.
To reduce your exposure to these chemicals: work
in a well ventilated area, and work with approved
safety equipment, such as dust masks that are spe-
cially designed to filter out microscopic particles.
6
Important Safety Information
FOR BATTERY CHARGER AND
BATTERY PACK
Important Safety Instructions
1. SAVE THESE INSTRUCTIONS–This manual con-
tains important safety and operating instructions
for battery charger LBC-81B.
2. Before using battery charger, read all instructions
and cautionary markings on battery charger,
battery pack, and product using battery pack.
3. CAUTION–To reduce the risk of injury, charge only
battery pack LBP-216. Other types of batteries
may burst causing personal injury and damage.
4. Do not expose charger and battery pack to rain or
snow.
5. To reduce risk of damaging the electric plug and
cord, pull by plug rather than cord when discon-
necting charger.
6. Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected
to damage or stress.
7. An extension cord should not be used unless
absolutely necessary. Use of improper extension
cord could result in a risk of fire and electric
shock. If extension cord must be used, make sure
that:
a. pins on plug of extension cord are the same
number, size and shape as those of plug on
charger.
b. extension cord is properly wired and in good
electrical condition.
c. wire size is large enough for ampere rating of
charger as specified below.
Recommended Minimum AWG Size
of Extension Cords for Battery Chargers
AC Input Rating Amperes AWG Size of Cord
Equal to or
greaterthan
But
lessthan
Length of Cord
(ft)
25 50 100 150
0 2 18 18 18 16
8. Do not operate charger with damaged cord or
plug; replace them immediately.
9. Do not operate charger if it has received a sharp
blow, been dropped, or otherwise damaged in any
way; take it to qualified service personnel.
10. Do not disassemble charger; take it to quali-
fied service personnel when service or repair is
required. Incorrect reassembly may result in a risk
of electric shock or fire.
11. To reduce the risk of electric shock, unplug
charger from outlet before attempting any main-
tenance or cleaning.
12. The charger and battery pack are specifically
designed to work together. Do not attempt to
charge any other cordless tool or battery pack
with this charger.
13. Do not attempt to charge the battery pack with
any other charger.
14. Do not attempt to disassemble the battery pack
housing.
15. Do not store the tool and battery pack in locations
where the temperature may reach or exceed
122°F (50 °C) (such as a metal tool shed, or a car
in the summer), which can lead to deterioration of
the storage battery.
16. Do not charge battery pack when the temperature
is BELOW 32 °F (0 °C) or ABOVE 104 °F (40 °C).
This is very important in order to maintain optimal
condition of the battery pack.
17. Do not incinerate the battery pack. It can explode
in a fire.
18. Avoid dangerous environment. Do not use charger
in damp or wet locations.
19. The charger is designed to operate on standard
household electrical power only. Do not attempt to
use it on any other voltage!
7
LDD-216 • LHD-216
Important Safety Information
20. Do not abuse cord. Never carry charger by cord or
yank it to disconnect from outlet. Keep cord away
from heat, oil and sharp edges.
21. Charge the battery pack in a well ventilated place;
do not cover the charger and battery pack with a
cloth, etc., while charging.
22. Use of an attachment not recommended may
result in a risk of fire, electric shock, or personal
injury.
23. Do not short the battery pack. A battery short
can cause a large current flow, over heating and
create the risk of fire or personal injury.
24. NOTE: If the supply cord of this appliance is
damaged, it must only be replaced by a repair
shop authorized by the manufacturer, because
special purpose tools are required.
25. TO REDUCE THE RISK OF ELECTRIC SHOCK, THIS
APPLIANCE HAS A POLARIZED PLUG (ONE BLADE
IS WIDER THAN THE OTHER). This plug will fit in
a polarized outlet only one way. If the plug does
not fit fully in the outlet, reverse the plug. If it
still does not fit, contact a qualified electrician to
install the proper outlet. Do not change the plug in
any way.
• Do not use other than the Greenlee battery packs
that are designed for use with this rechargeable
tool.
• Do not dispose of the battery pack in a fire, or
expose it to excessive heat.
• Do not drive the likes of nails into the battery
pack, subject it to shocks, dismantle it, or attempt
to modify it.
• Do not allow metal objects to touch the battery
pack terminals.
• Do not carry or store the battery pack in the same
container as nails or similar metal objects.
• Do not charge the battery pack in a high-
temperature location, such as next to a fire or
in direct sunlight. Otherwise, the battery may
overheat, catch fire, or explode.
• Never use other than the dedicated charger to
charge the battery pack. Otherwise, the battery
may leak, overheat, or explode.
• After removing the battery pack from the tool
or the charger, always reattach the pack cover.
Otherwise, the battery contacts could be shorted,
leading to a risk of fire.
8
Identification
1 2 3
4
5
5
6
7
8
13
14
17
11
10 9
12
15
16
1. Keyless drill chuck
2. Clutch handle
3. Speed selector switch
4. Forward/Reverse switch
5. Alignment marks
6. Battery pack release button
7. Battery pack (LBP-216)
8. Control panel
9. Overheat warning lamp (battery)
10. LED light on/off button
11. LED light
12. Battery low warning lamp
13. Variable speed control trigger
14. Support handle
15. Battery charger (LBC-81B)
16. Battery pack cover
17. Li-ion battery pack dock
9
LDD-216 • LHD-216
Specifications
LDD-216/LHD-216 Main Unit
Motor: 21.6 V DC
No Load Speed:
Low: 100 to 400 rpm
High: 350 to 1500 rpm
Chuck Capacity: ø 1/16" to 1/2"
(1.5 mm to 13 mm)
Capacity:
Screw Driving:
Machine Screw: 3/10"
Wood Screw: ø 3/8" (10 mm)
Self-drilling Screw: ø 3/16" (6 mm)
Drilling:
For Wood: ø 1-1/2" (38 mm)
For Metal: ø 1/2" (13 mm)
For Masonry (LHD-216 only): ø 1/2" (13 mm)
Clutch Torque (approx.):
8.8 in-lb (1 Nm)
61 in-lb (6.9 Nm)
Blow Rate per Minute (LHD-216 only):
Low: 1800 to 7200 bpm
High: 6300 to 27,000 bpm
Overall Length:
LDD-216: 9-1/8" (232 mm)
LHD-216: 9-5/8" (245 mm)
Weight (with battery):
LDD-216: 5.39 lb (2.45 kg)
LHD-216: 5.61 lb (2.55 kg)
LBC-81B Battery Charger
Electrical Rating: Refer to the rating plate on the
bottom of the charger.
Weight: 2.1 lb (0.95 kg)
LBP-216 Battery Pack
Storage Battery: Li-ion battery
Battery Voltage: 21.6 V DC (3.6 V × 6 cells)
Charge Time:
Usable: 55 min
Full: 70 min
Accessories
Refer to the Greenlee Accessory Guide for accessories
that can be used with this tool.
10
Operation—Power Tool
• To prevent excessive temperature increase of the
tool surface, do not operate the tool continuously
using two or more battery packs. The tool needs
cool-off time before switching to another pack.
• Do not close up vent holes on the sides of the
body during operation. Otherwise, the machine
function is adversely affected to cause a failure.
• Do NOT strain the tool (motor). This may cause
damage to the unit.
• To prevent burns, use the tool in such a way as
to prevent the air from the body vent holes from
blowing directly onto your skin.
• If the tool body becomes very hot or does not
work properly, remove the battery pack and do
not use. Have it checked by an authorized service
center.
Symbol Explanation
V Volts
Direct current (DC)
no No load speed
Drill setting
Rotation with hammering
(LHD-216 only)
rpm Revolutions per minute
• Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.
• Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Suchpre-
ventive safety measures reduce the risk of start-
ing the power tool accidentally.
• When storing or carrying the tool, set the Forward/
Reverse switch to the center position (switch
lock). Accidentally starting the tool may result in
injury.
• Do not strain the tool by holding the speed control
trigger halfway (speed control mode) so that the
motor stops. The protection circuit will activate
and may prevent speed control operation. If this
happens, release the speed control trigger and
squeeze again for normal operation.
• Be careful not to get dust inside the chuck.
• Do not drop the tool.
Failure to observe these precautions may result in
injury or property damage.
11
LDD-216 • LHD-216
Operation—Power Tool (cont’d)
Bit Installation
Pinch points:
• Due to possibility of accidental
operation, remove battery when
changing bits.
• Keep hands away from spinning
parts while tool is in operation.
Failure to observe these warnings
could result in injury.
This tool is equipped with a keyless drill chuck. When
attaching or removing a bit, disconnect the battery
pack from the tool and place the switch in the center
position (switch lock).
Attaching the Bit
Insert the bit and turn the lock collar clockwise (viewed
from the front) to tighten firmly until it stops clicking.
Lock collar
Removing the Bit
Turn the lock collar counterclockwise (viewed from the
front), and then remove the bit.
Note: If excessive play occurs in the chuck, secure the
drill in place and (1) open the chuck jaws by turning
the lock collar, and (2) tighten the screw (left-handed
screw) with a screwdriver by turning it counterclock-
wise (viewed from the front).
Support Handle
Place the support handle at the desired position, and
tighten the handle securely.
Tighten
Loosen
Remove the handle before placing the tool in the
storage case.
Variable Speed Trigger Operation
1. The speed increases with the amount of depres-
sion of the trigger.
When beginning work, depress the trigger slightly
to start the rotation slowly.
2. A feedback electronic controller is used to give a
strong torque even in low speed.
3. The brake operates when the trigger is released
and the motor stops immediately.
Note: When the brake operates, a braking sound may
be heard. This is normal.
12
Forward/Reverse Switch Operation
• If the bit becomes jammed, immediately release
the trigger to prevent an overload which can
damage the battery pack or motor. Use reverse
motion to loosen jammed bits.
• To prevent damage, do not operate Forward/
Reverse switch until the bit comes to a complete
stop.
• Do NOT operate the Forward/Reverse switch
when the trigger switch is on. The battery will dis-
charge rapidly and damage to the unit may occur.
Forward Reverse
Switch lock
Forward Rotation Switch Operation
1. Push the switch for forward (clockwise) rotation.
2. Depress the trigger slightly to start the tool slowly.
3. The speed increases with the amount of depres-
sion of the trigger for efficient tightening of
screws and drilling. The brake operates and the
chuck stops immediately when the trigger is
released.
4. After use, set the switch to its center position
(switch lock).
Reverse Rotation Switch Operation
1. Push the switch for reverse (counterclockwise)
rotation. Check the direction of rotation before
use.
2. Depress the trigger slightly to start the tool slowly.
3. After use, set the switch to its center position
(switch lock).
Switch Lock Operation
Push the switch to its centered position to lock the
tool. In the switch lock position, the trigger will not be
able to be depressed and the tool will not be allowed
to operate.
Clutch Torque Setting
Test the setting before actual operation.
LDD-216: Adjust the torque to one of the 18 clutch
settings for driving fasteners or the drill setting for
hole-making operations.
LHD-216: Adjust the torque to one of the 18 clutch
settings for driving fasteners, or the drill setting or
hammer setting
for hole-making operations.
Note: Always stop operating the tool and disengage
it from the work before rotating the clutch handle to
switch between the drill and hammer settings.
The lower clutch settings deliver less torque than the
higher clutch settings. During operation a ratcheting
sound may be heard; release the trigger. This sound
indicates that the clutch is slipping because the driving
operation has overcome the available torque for the
engaged clutch setting.
For operations that require higher torque, use the low
speed setting.
Set the scale at this mark ( )
Operation—Power Tool (cont’d)
13
LDD-216 • LHD-216
Operation—Power Tool (cont’d)
Speed Selection
• Check the speed selector switch before use.
• Use at low speed when high torque is needed
during operation. (Using at high speed when
high torque is required may cause a motor
breakdown.)
• Do not operate the speed selector switch (LOW-
HIGH) while pulling on the speed control trigger.
This can cause the rechargeable battery to wear
quickly or damage the internal mechanism of the
motor.
Choose a low or high speed to suit the application. The
lower speed setting allows for higher torque operation.
When the word “High” is visible, the tool is in the high
speed setting. When the word “Low” is visible, the tool
is in the low speed setting.
HIGH
LOW
The more the variable speed control trigger is pulled,
the higher the speed becomes.
Note: When the brake operates, a braking sound may
be heard. This sound indicates engagement of the bit
lock.
Bit-locking Function
With the trigger switch not engaged and a screwdriver
bit locked in place, the tool can be used as a manual
screwdriver (up to 353 in-lb or 40 Nm).
Note: There will be a little play in the chuck, but this is
not a malfunction.
This feature is handy for tightening screws that require
more torque than the maximum torque of the driver
(position on the clutch), for confirming the tight-
ness of a screw, or to loosen an extremely tight screw.
Control Panel
• DO NOT STARE INTO WORK LIGHT. Use of controls
or adjustments or performance of procedures
other than those specified herein may result in
hazardous radiation exposure.
• Do not use it as a substitute for a regular
flashlight.
(1)
(3)
(2)
LED Light (1)
Note: To use the LED light, depress the trigger once.
Press the LED light button.
Pressing
toggles the LED light on and off.
The light illuminates with very low current, and it does
not adversely affect the per-
formance of the driver during
use or its battery capacity.
The built-in LED light is
designed to illuminate the
small work area temporarily.
After installing the battery or
if tool has been idle for more
than 5 minutes, the work light will not illuminate until
the trigger has been initially depressed.
14
Operation—Power Tool (cont’d)
This product has a built-in LED light. This product
is classified into “Class 1 LED Product” to IEC (EN)
60825-1:2001.
Class 1 LED Product
Overheat Warning Lamp (2)
Off
(normal
operation)
Illuminated:
Overheat (motor)
Flashing:
Overheat (battery)
Indicates operation has been halted due
to motor or battery overheating.
To protect the motor or battery, be sure to note the
following when carrying out this operation.
• The overheating protection feature halts driver
operation to protect the battery pack in the event
of overheating. The overheat warning lamp on the
control panel flashes when this feature is active.
• If the overheating protection feature activates, allow
the driver to cool thoroughly (at least 30 minutes).
The driver is ready for use when the overheat
warning lamp goes out.
• Avoid using the driver in a way that causes
the overheating protection feature to activate
repeatedly.
• If the tool is operated continuously under high-load
conditions or if it is used in hot-temperature condi-
tions (such as during summer), the overheating
protection feature may activate frequently.
• If the tool is used in cold-temperature conditions
(such as during winter) or if it is frrequently stopped
during use, the overheating protection feature may
not activate.
Battery Low Warning Lamp (3)
Off
(normal operation)
Flashing (no charge)
Battery protection feature active.
Excessive (complete) discharging of lithium-ion
batteries shortens their service life dramatically. The
driver includes a battery protection feature designed to
prevent excessive discharging of the battery pack.
The battery protection feature activates immediately
before the battery loses its charge, causing the battery
low warning lamp to flash
If you notice the battery low warning lamp flashing,
charge the battery pack immediately.
Recommended Grip
When necessary, attach and use the support handle
with two hands. If the support handle is not attached,
use the grip to hold and operate the driver with one
hand. Also, if the support handle is not attached and
additional force is needed, push against the rear end
of the driver with your other hand.
15
LDD-216 • LHD-216
Operation—Battery Pack
Under abusive conditions, liquid may be ejected
from battery; avoid contact. If contact acciden-
tally occurs, flush with water. If liquid contacts
eyes, additionally seek medical help immedi-
ately. Liquid ejected from the battery may cause
irritation or burns.
• Ensure the trigger is not pressed down before
inserting battery pack. Inserting battery pack
into power tools that have the trigger pressed
down invites accidents.
• When storing the battery or when battery pack
is not in use, keep it away from other metal
objects such as paper clips, coins, keys, nails,
screws, or other small metal objects that
can make a connection from one terminal to
another, causing the battery to short. Shorting
the battery terminals together may cause a large
current overflow resulting in overheating, burns,
or a fire. Refer to the “Maintenance” section for
cleaning procedures.
Other types of batteries may burst, causing personal
injury and damage.
• Do not attempt to charge the battery pack with
any other charger. Otherwise, the battery may
leak, overheat, or explode.
• Do not drive nails into the battery pack, subject it
to shocks, disassemble the battery pack housing,
or attempt to modify it.
• The charger is designed to operate on standard
household electrical power only. Do not attempt to
use it on any other voltage!
• Use of an attachment not recommended may
result in a risk of fire, electric shock, or personal
injury.
• Recharge only with the charger specified by
the manufacturer. A charger that is suitable for
one type of battery pack may create a risk of fire
when used with another battery pack.
• Use power tools only with specifically desig-
nated battery packs. Use of any other battery
packs may create a risk of injury and fire.
Note: SAVE THESE INSTRUCTIONS
This manual contains important safety and operating
instructions for battery charger LBC-81B.
Note: Battery Pack Life
The rechargeable batteries have a limited life. If the
operation time becomes extremely short after recharg-
ing, replace the battery pack with a new one.
16
Operation—Battery Pack (cont’d)
• Do not store the tool and battery pack in locations
where the temperature may reach or exceed
122°F (50°C) (such as a metal tool shed, or a
car in the summer), or below -4°F (-20°C) which
can lead to deterioration of the storage battery.
• Do not incinerate the battery pack. It can explode
in a fire.
• The operating temperature range is between
32°F (0°C) and 104°F (40°C). If the battery
pack is used when the battery temperature is
below 32°F (0°C), the tool may fail to function
properly.
Attaching or Removing Battery Pack
To connect the battery pack:
1. Line up the alignment marks and attach the
battery pack.
2. Slide the battery pack until it locks into position.
Alignment marks
To remove the battery pack:
Push the button on the front to release the battery
pack.
Release
button
Appropriate Use of Li-ion
Battery Pack
• When charging the battery pack, confirm that the
terminals on the battery charger are free of foreign
substances such as dust, water, etc., Clean the
terminals before charging the battery pack if any
foreign substances are found on the terminals. The
life of the battery pack terminals may be affected
by foreign substances such as dust, water, etc.,
during operation.
• When operating the battery pack, make sure the
workplace is well ventilated.
• When the battery pack is removed from the main
body of the tool, replace the battery pack terminal
cover immediately in order to prevent dust or dirt
from contaminating the battery terminals and
causing a short circuit.
17
LDD-216 • LHD-216
Operation—Battery Charger
• Charger plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) char-
gers. Unmodified plugs and matching outlets will
reduce risk of electric shock.
• Do not abuse the cord. Never use the cord for
carrying, pulling, or unplugging the charger.
Keep cord away from heat, oil, sharp edges,
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
• To reduce the risk of electric shock, unplug
charger from outlet before attempting any main-
tenance or cleaning.
• If the temperature of the battery pack falls below
approximately 14°F (−10°C), charging automati-
cally stops to prevent degradation of the battery.
• It is strongly urged that the battery pack not be
charged when the temperature is BELOW 32°F
(0°C) or ABOVE 104°F (40°C). This is very
important in order to maintain optimal condition of
the battery pack.
• When charging a cool battery pack [below 32°F
(0°C)] in a warm place, leave the battery pack
at the place and wait for more than one hour to
warm up the battery to the level of the ambient
temperature.
• Cool down the charger when charging more than
two battery packs consecutively.
• Charge the battery pack in a well ventilated place;
do not cover the charger and battery pack with a
cloth, etc., while charging.
• Do not insert your fingers into contact hole, when
holding charger or any other occasions.
• This plug will fit in a polarized outlet only one way.
If the plug does not fit fully in the outlet, reverse
the plug. If it still does not fit, contact a qualified
electrician to install the proper outlet. Do not
change the plug in any way
• To reduce risk of damaging the electric plug and
cord, pull by plug rather than cord when discon-
necting charger.
• Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected
to damage or stress.
• Do not operate charger with damaged cord or
plug—replace them immediately.
• An extension cord should not be used unless
absolutely necessary.
• Use of improper extension cord could result in a
risk of fire and electric shock.
• If extension cord must be used, make sure that:
– Pins on plug of extension cord are the same
number, size and shape as those of plug on
charger.
– Extension cord is properly wired and in good
electrical condition.
– Wire size is large enough for ampere rating of
charger as specified below.
18
Operation—Battery Charger (cont’d)
Recommended Minimum AWG Size
of Extension Cords for Battery Chargers
AC Input Rating Amperes AWG Size of Cord
Equal to or
greaterthan
But
lessthan
Length of Cord
(ft)
25 50 100 150
0 2 18 18 18 16
Note: If the supply cord of this appliance is damaged,
it must only be replaced by a repair shop authorized by
the manufacturer, because special purpose tools are
required.
The charger and battery pack are specifically designed
to work together. Do not attempt to charge any other
cordless tool or battery pack with this charger.
To reduce the risk of electric shock, this appliance has
a polarized plug (one blade is wider that the other).
To prevent the risk of fire or damage to the battery
charger:
• Do not use power source from an engine generator.
• Do not cover vent holes on the charger and the
battery pack.
• Unplug the charger when not in use.
• Do not operate charger if it has received a sharp
blow, been dropped, or otherwise damaged in any
way; take it to qualified service personnel.
• Do not disassemble charger; take it to quali-
fied service personnel when service or repair is
required. Incorrect reassembly may result in a risk
of electric shock or fire.
• Do NOT charge the battery for more than 2hours.
Charging Li-ion Battery Pack
1. Plug the charger into the AC outlet.
2. If the power lamp does not light immediately after
the charger is plugged in, or if after the standard
charging time the charging lamp does not flash
quickly in green, consult an authorized dealer.
3. Insert the battery pack firmly into the charger.
• Line up the alignment marks and place the
battery onto the dock on the charger.
• Slide forward in the direction of the arrow.
Alignment marks
4. During charging, the charging lamp will be lit.
When charging is completed, an internal elec-
tronic switch will automatically be triggered to
prevent overcharging.
• Charging will not start if the battery pack is
warm (for example, immediately after heavy-
duty operation).
• The orange standby lamp will flash until the
battery cools down. Charging will then begin
automatically.
5. The charge lamp (green) will flash slowly once the
battery is approximately 80% charged.
6. When charging is completed, the charging lamp
will turn off.
7. Remove the battery pack while the battery pack
release button is held up.
Battery pack
release button
Notes: The battery pack is not fully charged at the
time of purchase. Be sure to charge the battery before
use.
This product should only be used to charge Greenlee
lithium-ion batteries sold with this product.
19
LDD-216 • LHD-216
Operation—Battery Charger (cont’d)
Appropriate Use of BatteryCharger
• Make sure the terminals of the battery charger
are not contaminated with liquid, grease, or other
substances before charging the battery pack. If
you notice that the terminals of the battery charger
are contaminated, be sure to wipe or take them
off before use. The life of the battery pack may
adversely be affected when the terminals are
clogged with the dust or dirt which becomes solid
with liquid or grease.
• During charging, the charger may become slightly
warm. This is normal.
• If the temperature of the battery pack is 32°F
(0°C) or less, charging takes longer to fully charge
the battery pack than the standard charging time.
Even when the battery is fully charged, it will have
approximately 50% of the power of a fully charged
battery at normal operating temperature.
• If a fully charged battery pack is inserted into the
charger again, the charging lamp lights up. After
several minutes, the charging lamp may turn off to
indicate the charging is completed.
Lamp Indications
Green Lamp Off
Charging is completed (full charge).
Green Flashing
Battery is approximately 80% charged (usable charge).
Green Lit
Now charging.
Green Lamp Off
Charger is plugged into the AC outlet. Ready to charge.
Charging Status Lamp
Left: green; Right: orange will be displayed.
Orange Lit
Battery pack is cool. The battery pack is being charged slowly to reduce the load
on the battery.
Orange Flashing
Battery pack is warm. Charging will begin when temperature of battery pack
drops.
If the temperature of the battery pack is 14°F (–10°C) or less, the charging
status lamp (orange) will also start flashing. Charging will begin when the
temperature of the battery pack goes up.
Both Orange and Green Flashing
Charging is not possible. Clogged with dust or malfunction of the battery pack.
Lamp off Lit Flashing
20
Maintenance
To avoid severe personal injury, always remove
the battery pack from the tool before starting any
maintenance procedure.
No regular maintenance is needed for this power tool
other than the following:
• Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may
affect the power tool’s operation. If damaged, have
the power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly main-
tained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
• Use only a dry, soft cloth for wiping the unit.
• Do not use solvents or flammable liquids to clean
the tool body. Solvents or flammable liquids
could ignite and cause serious injury or property
damage.
• Do not use a damp cloth, thinner, benzene, or
other volatile solvents for cleaning.
• To prevent the risk of serious personal injury or
fire, do not try to repair the tool by yourself. Never
disassemble or modify the tool body. There are no
user-repairable parts inside.
• Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
Failure to observe this precaution may result in injury
and property damage.
Check for power tool service stations on the
Greenlee website at www.greenlee.com or contact
Greenlee Technical Support at 1-800-435-0786.
When using accessories such as hole saws, step bits,
auger bits, etc., always use manufacturer’s instruc-
tions for their usage.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/