Avanti BCA180 User manual

CHI-1442P / 1802P

F

GB

D

E

I

P

NL

S

DK

N

FIN

GR

TR

PERCEUSE-VISSEUSE À PERCUSSION SANS FIL MANUEL D’UTILISATION 1

CORDLESS IMPACT DRILL DRIVER USER’S MANUAL 7

AKKU-SCHLAGBOHRMASCHINE-SCHRAUBER BEDIENUNGSANLEITUNG 12

TALADRADORA-ATORNILLADORA DE PERCUSIÓN SIN CABLE MANUAL DE UTILIZACIÓN 18

TRAPANO AVVITATORE A PERCUSSIONE A BATTERIA MANUALE PER L’UTENTE 24

BERBEQUIM-APARAFUSADORA COM PERCUSSÃO SEM FIO MANUAL DE UTILIZAÇÃO 30

ACCU KLOPBOOR-SCHROEFMACHINE GEBRUIKERSHANDLEIDING 36

SLADDLÖS SLAGBORRMASKIN-SKRUVDRAGARE INSTRUKTIONSBOK 42

BATTERIDREVEN SLAGBORE-SKRUEMASKINE BRUGERVEJLEDNING 48

OPPLADBAR SLAGBOREMASKIN-SKRUTREKKER BRUKSANVISNING 54

JOHDOTON ISKUPORAKONE-RUUVITALTTA KÄYTTÄJÄN KÄSIKIRJA 59

ΕΠΑΝΑΦΟΡΤΙΖΟΜΕΝΟ ΚΡΟΥΣΤΙΚΟ ΔΡΑΠΑΝΟΚΑΤΣΑΒΙΔΟ ΟΔΗΓΙΕΣ ΧΡΗΣΗΣ 64

ÜTVEFÚRÓ-CSAVAROZÓ GÉP, VEZETÉK NÉLKÜLI HASZNÁLATI ÚTMUTATÓ 71

AKUMULÁTOROVÝ VRTACÍ ŠROUBOVÁK S PŘÍKLEPEM NÁVOD K OBSLUZE 77

ÄääìåìãüíéêçÄü ìÑÄêçÄü ÑêÖãú-òìêìèéÇÖêí êìäéÇéÑëíÇé èé ùäëèãìÄíÄñàà 83

MAŞINA DE GĂURIT ŞI ÎNŞURUBAT CU PERCUŢIE FĂRĂ FIR MANUAL DE UTILIZARE 89

UDAROWA BEZPRZEWODOWA WIERTARKO-WKRĘTARKA PODRĘCZNIK OBSŁUGI 95

BATERIJSKI UDARNI VRTALNIK IN VIJAČNIK UPORABNIŠKI PRIROČNIK 101

BEÆI»NA UDARNA BU©ILICA-ZAVRTA» KORISNI»KI PRIRU»NIK 106

KABLOSUZ VURUŞLU BURGU MATKAP KULLANMA KILAVUZU 111

HU

CZ

RU

RO

PL

SLO

HR

960931157-01.indd A1960931157-01.indd A1 7/10/07 4:19:44 PM7/10/07 4:19:44 PM

Page is loading ...

Attention ! Il est indispensable que vous lisiez les instructions contenues dans ce manuel avant

le montage et la mise en service de l’appareil.

Important! It is essential that you read the instructions in this manual before mounting and operating

this machine.

Achtung! Bitte lesen Sie unbedingt vor Montage und Inbetriebnahme die Hinweise dieser

Bedienungsanleitung.

¡Atención! Es imprescindible que lea las instrucciones de este manual antes del montaje y de la

puesta en servicio.

Attenzione! Prima di procedere al montaggio e alla messa in funzione, è indispensabile leggere

attentamente le istruzioni del presente manuale.

Atenção! É indispensável ler as instruções deste manual antes de montar e pôr em serviço.

Let op ! Het is absoluut noodzakelijk vóór montage en inbedrijfstelling de aanwijzingen in deze

handleiding te lezen.

Observera! Det är nödvändigt att läsa instruktionerna i denna bruksanvisning före montering och

driftsättning.

OBS! Denne brugsanvisning skal læses igennem inden montering og ibrugtagning.

Advarsel! Vennligst les instruksjonene i denne bruksanvisningen før du monterer og tar i bruk

maskinen.

Huomio! On ehdottoman välttämätöntä lukea tässä käyttöohjeessa annetut ohjeet ennen

asennusta ja käyttöönottoa.

Προσοχή!

Είναι απαραίτητο να διαβάσετε τις συστάσεις των οδηγιών αυτών πριν τη

συναρμολόγηση και τη θέση σε λειτουργία

Figyelem! Feltétlenül fontos, hogy a jelen használati útmutatóban foglalt előírásokat az

összeszerelés és az üzembe helyezés ellőt elolvassa!

Důležité upozornění! Před montáží nářadí a uvedením do provozu je nutné si přečíst následující pokyny.

ÇÌËÏ‡ÌËe! èee‰ Ò·ÓÍÓÈ Ë Á‡ÔÛÒÍÓÏ ËÌÒÚÛÏeÌÚ‡ ÌeÓ·ıÓ‰ËÏÓ ÔÓ˜eÒÚ¸ ËÌÒÚÛÍˆËË ËÁ Ì‡ÒÚÓﬂ˘e„Ó

ÛÍÓ‚Ó‰ÒÚ‚‡.

Atenţie! Este indispensabil sã citiţi instrucţiunile conţinute în acest mod de utilizare înainte de montaj

şi de punerea în funcţiune.

Uwaga! Przed montowaniem i uruchomieniem, koniecznie musicie się Państwo zapoznać

z zaleceniami zawartymi w niniejszym sposobie użycia.

Pomembno! Zelo pomembno je, da pred namestitvijo in prvo uporabo te naprave preberete

navodila v tem priročniku.

Upozorenje!

Vaæno je da upute u ovom KorisniËkom priruËniku proËitate prije postavljanja i uporabe

ovog alata.

Dikkat! Montajdan ve aletin kullanımına başlamadan bu kılavuzda bulunan talimatları

okumanız gerekmektedir.

960931157-01.indd A3960931157-01.indd A3 7/10/07 10:45:00 AM7/10/07 10:45:00 AM

Sous réserve de modifications techniques / Subject to technical modifications / Technische Änderungen vorbehalten /

Bajo reserva de modificaciones técnicas / Con riserva di eventuali modifiche tecniche / Com reserva de modificações técnicas /

Technische wijzigingen voorbehouden / Med förbehåll för tekniska ändringar / Med forbehold for tekniske ændringer /

Med forbehold om tekniske endringer / Tekniset muutokset varataan / Υπό την επιφύλαξη τεχνικών τροποποιήσεων /

A műszaki módosítás jogát fenntartjuk / Změny technických údajů vyhrazeny /

åÓ„ÛÚ ·˚Ú¸ ‚ÌeÒeÌ˚ ÚeıÌË˜eÒÍËe ËÁÏeÌeÌËﬂ /

Sub rezerva modificaţiilor tehnice / Z zastrzeżeniem modyfikacji technicznych / Tehnične spremembe dopuščene

Podloæno tehniËkim promjenama / Teknik düzeltmeler hakkı saklıdır

960931157-01.indd A4960931157-01.indd A4 7/10/07 10:45:02 AM7/10/07 10:45:02 AM

Page is loading ...

7

English

GB

D E I P NL S DK N GR H CZ RUS ROFINFR SLO HR TRPL

GENERAL SAFETY RULES

WARNING

Read all instructions. Failure to follow all

instructions listed below may result in electric

shock, fire and/or serious injury. The term "power

tool'' in all of the warnings listed below refers

to your mains operated (corded) power tool or

battery operated (cordless) power tool.

SAVE THESE INSTRUCTIONS.

1) WORK AREA

a) Keep work area clean and well lit. Cluttered and

dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases, or dust. Power tools

create sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while

operating a power tool. Distractions can cause you

to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed(grounded) power

tools. Unmodified plugs and matching outlets will

reduce risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool will increase

the risk of electric shock.

d) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk

of electric shock.

e) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of

electric shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use

common sense when operating a power tool. Do

not use a power tool while you are tired or under the

influence of drugs, alcohol or medication. A moment

of inattention while operating power tools may result

in serious personal injury.

b) Use safety equipment. Always wear eye protection.

Safety equipment such as dust mask, non-skid

safety shoes, hard hat, or hearing protection used for

appropriate conditions will reduce personal injuries.

c) Avoid accidental starting. Ensure the switch is in

the off position before plugging in. Carrying power

tools with your finger on the switch or plugging in

power tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may

result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times. This enables better control of

the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long

hair can be caught in moving parts.

g) If devices are provided for the connection of dust

extraction and collection facilities, ensure these

are connected and properly used. Use of these

devices can reduce dust related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the correct power

tool for your application. The correct power tool will

do the job better and safer at the rate for which it was

designed.

b) Do not use the power tool if the switch does not

turn it on and off. Any power tool that can not be

controlled with the switch is dangerous and must be

repaired.

c) Disconnect the plug from the power source before

making any adjustments, changing accessories,

or storing power tools. Such preventive safety

measures reduce the risk of starting the power tool

accidentally.

d) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the

power tool or these instructions to operate the

power tool. Power tools are dangerous in the hands

of untrained users.

e) Maintain power tools. Check for misalignment

or bindling of moving parts, breakage of parts and

any other condition that may affect the power tools

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

7

960931157-01.indd 7960931157-01.indd 7 7/10/07 10:45:07 AM7/10/07 10:45:07 AM

8

English

GB

D E I P NL S DK N GR H CZ RUS ROFINFR SLO HR TRPL

GENERAL SAFETY RULES

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc.,

in accordance with these instructions and in the

manner intended for the particular type of power

tool, taking into account the working conditions

and the work to be performed. Use of the power

tool for operations different from intened could result

in a hazardous situation.

5) BATTERY TOOL USE AND CARE

a) Ensure the switch is in the off position before

inserting battery pack. Inserting the battery pack

into power tools that have the switch on invites

accidents.

b) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used

with another battery pack.

c) Use power tools only with specifically designated

battery packs. Use of any other battery packs may

create a risk of injury and fire.

d) When battery pack is not in use, keep it away

from other metal abjects like paper clips, coins,

keys, nails, screws, or other small metal objects

that can make a connection from one terminal to

another. Shorting the battery terminals together may

cause burns or a fire.

e) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid contacts

eyes, additionally seek medical help. Liquid ejected

from the battery may cause irritation or burns.

6) SERVICE

a) Have your power tool serviced by a qualified

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool is maintained.

7) SPECIAL RULES

a) Wear ear protectors with impact drills. Exposure to

noise can cause hearing loss.

CHARGER SAFETY

■ To reduce risk of injury, charge only nickel-cadmium

type rechargeable batteries. Other types of batteries

may burst, causing personal injury and damage.

■ Do not expose charger to wet or damp conditions.

■ Use of an attachment not recommended or sold by

the battery charger manufacturer may result in a risk

of fire, electric shock, or injuries to person.

■ To reduce risk of damage to charger body and

cord, pull by charger plug rather than cord when

disconnecting charger.

■ Make sure cord is located so that it will not be stepped

on, tripped over, or otherwise subjected to damage

and stress.

■ An extension cord should not be used unless

absolutely necessary. Use of improper extension

cord could result in a risk of fire and electric shock.

If extension cord must be used, make sure:

a. That pins on plug of extension cord are the same

number, size and shape as those of plug on charger.

b. That extension cord is properly wired and in good

electrical condition.

■ Do not operate charger with a damaged cord or

plug. If damaged, have it replaced immediately by a

qualified serviceman.

■ Do not operate charger if it has received a sharp

blow, been dropped, or otherwise damaged in any

way; take it to a qualified serviceman.

■ Do not disassemble charger; take it to a qualified

serviceman when service or repair is required.

Incorrect reassembly may result in a risk of electric

shock or fire.

■ To reduce risk of electric shock, unplug the charger

from outlet before attempting any maintenance or

cleaning. Turning off controls will not reduce this risk.

■ Disconnect charger from power supply when not in use.

■ Risk of electric shock. Do not touch uninsulated portion

of output connector or uninsulated battery terminal.

■ Save these instructions. Refer to them frequently and

use them to instruct others who may use this unit.

If you loan someone this unit, loan them these

instructions also.

8

960931157-01.indd 8960931157-01.indd 8 7/10/07 10:45:07 AM7/10/07 10:45:07 AM

9

English

GB

D E I P NL S DK N GR H CZ RUS ROFINFR SLO HR TRPL

SPECIFICATIONS

Model CHI-1442P CHI-1802P

Voltage 14.4 V 18 V

Chuck 2-13 mm 2-13 mm

Switch Variable speed Variable speed

No load speed (drill mode):

- Lo speed 0-360 min

-1

0-400 min

-1

- Hi speed 0-1300 min

-1

0-1400 min

-1

No load speed (impact mode):

- Lo speed 0-4680 min

-1

0-5200 min

-1

- Hi speed 0-16900 min

-1

0-18200 min

-1

Max. Torque 31 Nm 34 Nm

Weight - incl. battery pack 2.0 kg 2.20 kg

Battery pack BPP-1413 / BPP-1415 BPP-1813 / BPP-1815 / BPP-1817/

Charger BCA-144 / BC-1440 / BC-1415-S BCA-180 / BC-1800 / BC-1815-S

DESCRIPTION

1. Keyless chuck

2. Switch trigger

3. Direction of rotation selector (Forward/Reverse)

4. Screwdriver bits

5 . Battery pack

6. Latches

7. Depress latches to release battery pack

8. Torque adjusting Ring

9. To Decrease torque

10. To Increase torque

11. Impact mode

12. Drill mode

13. Reverse

14. Forward

15. Unlock(release)

16. Lock (tighten)

17. High speed

18. Low speed

19. Battery Charger

20. LED indicator

21. Battery Charger

22. Green Light

23. Red Light

OPERATION

CHARGING YOUR BATTERY PACK

The battery pack for your tool has been shipped in a low

charge condition to prevent possible problems. Therefore,

you should charge it prior to use.

Note: Batteries will not reach full charge the first time

they are charged. Allow several cycles for them to

fully charge.

TO CHARGE

■ Charge battery pack only with the charger provided.

■ Make sure power supply is normal house voltage, 230

volts, 50 Hz, AC only.

■ Connect charger to power supply.

■ Make sure charger plug and input jack are properly

connected.

■ Place battery pack in charger. Align raised rib on

battery pack with groove in charger.

■ Press down on battery pack to be sure contacts

on battery pack engage properly with contacts in

charger. When properly connected, red light will turn

on.

Charger: BCA-144/BCA-180

See Figure 7.

■ The LED indicator, which is located on the charging

stand, will light up when charger is properly

connected to power supply. This light indicates your

tool is charging and will remain on until charger is

disconnected from power supply.

■ After normal usage, 3-5 hours of charge time are

required to be fully charged. A minimum charge

time of 5 hours is required to recharge a completely

discharged tool.

9

960931157-01.indd 9960931157-01.indd 9 7/10/07 10:45:08 AM7/10/07 10:45:08 AM

10

English

GB

D E I P NL S DK N GR H CZ RUS ROFINFR SLO HR TRPL

OPERATION

Charger: BC-1440/BC-1415-S/BC-1800/BC-1815-S

See Figure 8.

LED WILL BE ON TO INDICATE STATUS OF

CHARGER AND BATTERY PACK

■ Red LED on = Fast charging mode.

■ Green LED on = Fully charged battery pack.

■ No LED on = Defective charge or battery pack.

■ When your battery pack becomes fully charged, the

red light will turn off and the green light will turn on.

■ After normal usage, 1 hour of charge time is required

to be fully charged. A minimum charge time of 1 to

1-1/2 hours is required to recharge a completely

discharged tool.

■ DO NOT place charger in an area of extreme heat

or cold. It will work best at temperatures above 10°C

and below 38°C

IMPORTANT INFORMATION FOR RECHARGING HOT

BATTERIES

When using your tool continuously, the batteries in your

battery pack will become hot. You should let a hot battery

pack cool down for approximately 30 minutes before

attempting to recharge.

TO INSTALL BATTERY PACK

■ Lock switch trigger on your drill by placing the

direction of rotation selector in center position.

See Figure 4.

■ Place battery pack in your drill. Align raised rib on

battery pack with groove inside drill. See Figure 2.

■ Make sure the latches on battery pack snap in place

and battery pack is secured in drill before beginning

operation.

TO REMOVE BATTERY PACK

■ Lock switch trigger on your drill by placing the

direction of rotation selector in center position.

See Figure 4.

■ Locate latches of battery pack and depress to release

battery pack from your drill. See Figure 2.

■ Remove battery pack from your drill.

ADJUSTING THE TORQUE

See Figure 3.

The tool is equipped with an adjustable torque clutch for

driving different types of screws into different materials.

Adjust the torque as necessary.

We recommend that you use carbide-tipped bits and

select impact mode when drilling in hard material such as

brick, tile, concrete, etc.

CAUTION

The impact drill is not designed for reverse

hammering. Failure to obey this caution may

result in property damage.

SWITCH

See Figure 4.

■ To turn your drill ON, depress the switch trigger.

■ To turn it OFF, release the switch trigger.

VARIABLE SPEED

This tool has a variable speed switch that delivers higher

speed and torque with increased trigger pressure. Speed

is controlled by the amount of switch trigger depression.

SWITCH LOCK

See Figure 4.

The switch trigger can be locked in the OFF position.

This feature can be used to prevent the possibility of

accidental starting when not in use. To lock switch trigger,

place the direction of rotation selector (Forward/Reverse

Selector) in center position.

Note: When selector is in center position, switch trigger

is locked.

REVERSIBLE

See Figure 4.

This tool has the feature of being reversible. The direction

of rotation is controlled by a selector located above the

switch trigger. With the drill held in normal operating

position, the direction of rotation selector should be

positioned to the left of the switch for drilling. The drilling

direction is reversed when the selector is to the right

of the switch. When the selector is in center position,

the switch trigger is locked. To stop, release switch trigger

and allow the chuck to come to a complete stop.

ELECTRIC BRAKE

This drill has an electric brake. When the trigger switch

is released, the chuck stops turning. When the brake is

functioning properly, sparks will be visible through the

vent slots on the housing. This is normal and is the action

of the brake.

10

960931157-01.indd 10960931157-01.indd 10 7/10/07 10:45:09 AM7/10/07 10:45:09 AM

11

English

GB

D E I P NL S DK N GR H CZ RUS ROFINFR SLO HR TRPL

OPERATION

KEYLESS CHUCK

See Figure 5.

Your drill has a keyless chuck. As the name implies,

you can hand tighten or release drill bits in the

chuck jaws. Rotate the chuck with your hand. Rotate

the chuck body with your other hand. The arrows on the

chuck indicate which direction to rotate the chuck body in

order to LOCK (tighten) or UNLOCK (release) the drill bit.

WARNING

Do not hold chuck body with one hand and use

power of the drill to tighten chuck jaws on drill bit.

Chuck body could slip in your hand or your hand

could slip and come in contact with rotating drill bit.

This could cause an accident resulting in serious

personal injury.

ADJUSTING THE SPEED

See Figure 6.

Follow these steps to adjust the speed.

■ For high speed: Slide the two-speed gear train switch

to “2”.

■ For low speed: Slide the two-speed gear train switch

to “1”.

Note: If you have difficulty changing from one gear

range to the other, turn the chuck by hand until the gears

engage.

CAUTION

To prevent gear damage, always allow chuck to

come to a complete stop before changing the

speed or the direction of rotation.

MAINTENANCE

WARNING

When servicing, use only identical replacement

parts. Use of any other part may create a hazard

or cause product damage.

Avoid using solvents when cleaning plastic parts.

Most plastics are susceptible to damage from various

types of commercial solvents and may be damaged

by their use. Use clean cloths to remove dirt, dust, oil,

grease, etc.

WARNING

Do not at any time let brake fluids, gasoline,

petroleum-based products, penetrating oils,

etc. come in contact with plastic parts. They

contain chemicals that can damage, weaken or

destroy plastic.

Do not abuse power tools. Abusive practices can damage

tool as well as workpiece.

WARNING

Do not attempt to modify this tool or create

accessories not recommended for use with

this tool. Any such alteration or modification is

misuse and could result in a hazardous condition

leading to possible serious personal injury.

ENVIRONMENTAL PROTECTION

Recycle raw materials instead of disposing

as waste. The machine, accessories

and packaging should be sorted for en-

vironmental-friendly recycling.

960931157-01.indd 11960931157-01.indd 11 7/10/07 10:45:09 AM7/10/07 10:45:09 AM

Page is loading ...

F

GARANTIE - CONDITIONS

Ce produit Ryobi est garanti contre les vices de fabrication et les pièces

défectueuses pour une durée de vingt-quatre (24) mois, à compter de

la date faisant foi sur l'original de la facture établie par le revendeur à

l'utilisateur final.

Les détériorations provoquées par l'usure normale, par une utilisation ou

un entretien anormal ou non autorisé, ou par une surcharge sont exclues

de la présente garantie de même que les accessoires tels que batteries,

ampoules, lames, embouts, sacs, etc.

En cas de mauvais fonctionnement au cours de la période de garantie,

veuillez envoyer le produit NON DÉMONTÉ avec la preuve d'achat à votre

fournisseur ou au Centre Service Agréé Ryobi le plus proche de chez

vous.

Vos droits légaux se rapportant aux produits défectueux ne sont pas remis

en cause par la présente garantie.

GB

WARRANTY - STATEMENT

All Ryobi products are guaranteed against manufacturing defects and

defective parts for a period of twenty four (24) months from the date

stated on the original invoice drawn up by the retailer and given to the

end user.

Deterioration caused by normal wear and tear, unauthorised or improper

use or maintenance, or overload are excluded from this guarantee as are

accessories such as battery packs, light bulbs, blades, fittings, bags, etc.

In the event of malfunction during the warranty period, please take the

NON-DISMANTLED product, along with the proof of purchase, to your

retailer or nearest Authorised Ryobi Service Centre.

This warranty in no way affects your legal rights concerning defective

products.

D

GARANTIE - BEDINGUNGEN

Für alle Ryobi-Produkte gilt eine Garantie gegen Material- und

Verarbeitungsfehler für einen Zeitraum von vierundzwanzig (24)

Monaten ab dem Datum der vom Wiederverkäufer für den Endbenutzer

ausgestellten Originalrechnung.

Fehler, die auf Grund einer normalen Abnutzung, einer unberechtigten oder

falschen Wartung oder Handhabung oder durch eine Überbelastung auftreten,

sind von der Garantie ausgeschlossen. Dies gilt auch für Zubehörteile wie

Batterien, Glühbirnen, Sägeblätter, Ansatzstücke, Beutel usw.

Senden Sie das Produkt im Fall eines Defekts innerhalb des

Garantiezeitraumes in NICHT ZERLEGTEM Zustand zusammen

mit dem Kaufnachweis an Ihren Händler oder Ihr nächstes Ryobi-

Kundendienstzentrum zurück.

Diese Garantie hat keine Auswirkungen auf Ihre gesetzlichen Rechte in

Bezug auf fehlerhafte Produkte.

E

GARANTÍA - CONDICIONES

Este producto Ryobi está garantizado contra los defectos de fabricación

y las piezas defectuosas por un período de veinticuatro (24) meses, a

partir de la fecha que figura en el original de la factura establecida por el

distribuidor al usuario final.

Se excluyen de la presente garantía los deterioros provocados por

un desgaste normal, una utilización o mantenimiento incorrecto o no

autorizado, y una sobrecarga, así como los diversos accesorios: baterías,

bombillas, hojas, puntas, bolsas, etc.

En caso de funcionamiento incorrecto durante el período de la garantía, envíe

el producto SIN DESMONTAR con la prueba de compra a su proveedor o al

Centro de Servicio Acreditado Ryobi más cercano a su domicilio.

Los derechos legales relacionados con los productos defectuosos no son

cuestionados por la presente garantía.

I

GARANZIA - CONDIZIONI

Questo prodotto Ryobi è garantito contro tutti i difetti di fabbricazione e

pezzi difettosi per una durata di ventiquattro (24) mesi, a partire dalla data

indicata sull’originale della fattura compilata dal rivenditore e consegnata

all’utente finale.

Il deterioramento provocato dall’usura normale, da un utilizzo o una

manutenzione non conformi o non autorizzati, o da un sovraccarico,

è escluso dalla presente garanzia. La garanzia è esclusa anche per gli

accessori come batterie, lampadine, lame, punte, borse, ecc.

In caso di malfunzionamento nel corso del periodo di garanzia, riportare

il prodotto NON SMONTATO corredato della prova d’acquisto al fornitore

o al più vicino Centro di Assistenza Autorizzato Ryobi.

I diritti legali relativi ai prodotti difettosi non sono rimessi in causa dalla

presente garanzia.

P

GARANTIA - CONDIÇÕES

Este produto Ryobi está garantido contra os vícios de fabrico e as peças

defeituosas por um prazo de vinte e quatro (24) meses, a contar da

data que faz fé no original da factura emitida pelo vendedor ao utilizador

final.

As deteriorações provocadas pelo desgaste normal, por uma utilização

ou uma manutenção anormal ou não autorizada, ou por uma sobrecarga

ficam excluídas da presente garantia assim como os acessórios tais como

baterias, lâmpadas, lâminas, ponteiras, sacos, etc.

No caso de mau funcionamento durante o período de garantia, queira

enviar o produto NÃO DESMONTADO com a prova de compra ao seu

fornecedor ou ao Centro de Serviço Autorizado Ryobi mais próximo.

Os seus direitos legais relativos aos produtos defeituosos não são

prejudicados pela presente garantia.

NL

GARANTIEVOORWAARDEN

Dit Ryobi product is gewaarborgd tegen fabricagefouten en defecte

onderdelen gedurende een periode van vierentwintig (24) maanden,

te rekenen vanaf de officiële datum op het origineel van de door de

wederverkoper aan de eindgebruiker uitgeschreven rekening.

Beschadigingen veroorzaakt door normale slijtage, door abnormaal of

ongeoorloofd gebruik of onderhoud, of door overbelasting vallen niet

onder deze garantie, evenmin als accu's, lampen, bits, snijbladen,

zakken enz.

In geval van slechte werking tijdens de garantieperiode, wordt u verzocht

het NIET GEDEMONTEERDE product samen met de koopbon aan uw

leverancier of aan het dichtstbijzijnde Ryobi servicecentrum te sturen.

Deze garantie doet niet af aan uw wettelijke rechten met betrekking tot

defecte producten.

S

GARANTI - VILLKOR

Ryobi garanterar denna produkt mot fabrikationsfel och defekta delar

under tjugofyra (24) månader, räknat från det datum som anges

på originalfakturan fastställd av återförsäljaren och överlämnad till

slutanvändaren.

Denna garanti täcker inte skador som förorsakas av normalt slitage,

av onormal eller otillåten användning eller skötsel, eller av överbelastning.

Den täcker inte heller tillbehör som batterier, glödlampor, blad, ändstycken,

påsar, osv.

I händelse av felaktig funktion medan garantin är i kraft skall produkten

sändas UTAN ATT DEMONTERAS tillsammans med inköpsbeviset

till leverantören eller till närmaste servicecenter som auktoriserats av

Ryobi.

De rättigheter som lagen ger i förhållande till defekta produkter ifrågasätts

inte av denna garanti.

960931157-01.indd 116960931157-01.indd 116 7/10/07 10:47:28 AM7/10/07 10:47:28 AM

Page is loading ...

CHI-1442P CHI-1802P

Niveau de pression acoustique (84.5+3) dB(A) (84.5+3) dB(A)

Niveau de puissance acoustique (95.5+3) dB(A) (95.5+3) dB(A)

Valeur d'accélération de la moyenne

quadratique pondérée 17,6 m/s

2

17,6 m/s

2

Sound pressure level (84.5+3) dB(A) (84.5+3) dB(A)

Sound power level (95.5+3) dB(A) (95.5+3) dB(A)

Weighted root mean

square acceleration value 17.6 m/s

2

17.6 m/s

2

Schalldruckpegel (84.5+3) dB(A) (84.5+3) dB(A)

Schallleistungspegel (95.5+3) dB(A) (95.5+3) dB(A)

Beschleunigung des

quadratischen gewogenen Mittelwerts 17,6 m/s

2

17,6 m/s

2

Nivel de presión acústica (84.5+3) dB(A) (84.5+3) dB(A)

Nivel de potencia acústica (95.5+3) dB(A) (95.5+3) dB(A)

Valor de aceleración de la

media cuadrática ponderada 17,6 m/s

2

17,6 m/s

2

Livello di pressione acustica (84.5+3) dB(A) (84.5+3) dB(A)

Livello di potenza acustica (95.5+3) dB(A) (95.5+3) dB(A)

Valore d’accelerazione della

media quadratica ponderata 17,6 m/s

2

17,6 m/s

2

Nível de pressão acústica (84.5+3) dB(A) (84.5+3) dB(A)

Nível de potência acústica (95.5+3) dB(A) (95.5+3) dB(A)

Valor da aceleração da

média quadrática ponderada 17,6 m/s

2

17,6 m/s

2

Geluidsdrukniveau (84.5+3) dB(A) (84.5+3) dB(A)

Geluidsvermogensniveau (95.5+3) dB(A) (95.5+3) dB(A)

Versnellingswaarde van

de gewogen effectieve waarde 17,6 m/s

2

17,6 m/s

2

Ljudtrycksnivå (84.5+3) dB(A) (84.5+3) dB(A)

Ljudeffektnivå (95.5+3) dB(A) (95.5+3) dB(A)

Accelerationsvärde för

viktat kvadratiskt medeltal 17,6 m/s

2

17,6 m/s

2

Lydtryksniveau (84.5+3) dB(A) (84.5+3) dB(A)

Lydstyrkeniveau (95.5+3) dB(A) (95.5+3) dB(A)

Accelerationsværdi for

vægtet kvadratmiddeltal 17,6 m/s

2

17,6 m/s

2

Lydtrykknivå (84.5+3) dB(A) (84.5+3) dB(A)

Lydstyrkenivå (95.5+3) dB(A) (95.5+3) dB(A)

Veid kvadratisk middelverdi

av akselerasjonsverdien 17,6 m/s

2

17,6 m/s

2

Äänenpainetaso (84.5+3) dB(A) (84.5+3) dB(A)

Äänen tehotaso (95.5+3) dB(A) (95.5+3) dB(A)

Painotettu kiihdytyksen tehollisarvo 17,6 m/s

2

17,6 m/s

2

Επίπεδο ακουστικής πίεσης (84.5+3) dB(A) (84.5+3) dB(A)

Επίπεδο ακουστικής ισχύος (95.5+3) dB(A) (95.5+3) dB(A)

Tιμή επιτάχυνσης της σταθμισμένης

μέσης τετραγωνικής τιμής 17,6 m/s

2

17,6 m/s

2

Hangnyomás szint (84.5+3) dB(A) (84.5+3) dB(A)

Hangerő szint (95.5+3) dB(A) (95.5+3) dB(A)

A gyorsítás négyzetes

súlyozott átlag értéke 17,6 m/s

2

17,6 m/s

2

S

F

GB

D

E

I

P

NL

DK

N

FIN

GR

H

960931157-01.indd 119960931157-01.indd 119 7/10/07 10:47:31 AM7/10/07 10:47:31 AM

Page is loading ...

DÉCLARATION DE CONFORMITÉ

Nous déclarons sous notre propre responsabilité que ce produit

est en conformité avec les normes ou documents normalisés

suivants: