Electrolux Z425 Series User manual

Category
Vacuum cleaners
Type
User manual
Upright Vacuum Cleaner
Owner’s Guide
Household Type
Z425 Series
2
3
4
4
5
5 - 6
5
6
6 - 7
IMPORTANT
For any advice
on your cleaner and
to order filters and
accessories,
please telephone the
Electrolux Helpline on
08706 055055
www.electrolux.co.uk
IMPORTANT INFORMATION
GUARANTEE
QUICK REFERENCE
HOW TO ASSEMBLE
HOW TO USE
ROUTINE MAINTENANCE
Empty Dust Cup
Clean Dust Cup Filter
PROBLEM SOLVING
2
IMPOR
T
ANT INFORM
A
TION
To reduce the risk of fire, electric shock, or injury :
Do not use outdoors or on wet surfaces.
Do not leave vacuum cleaner when plugged in. Turn
off the switch and unplug the electrical cord when not in
use and before servicing.
Do not allow to be used as a toy. Close attention is
necessary when used by or near children.
Use only as described in this manual. Use only
manufacturer’s recommended attachments.
Do not use with damaged cord or plug. If vacuum cleaner
is not working as it should, has been dropped, damaged,
left outdoors, or dropped into water, return it to a service
center before using.
Do not pull or carry by cord, use cord as a handle, close
door on cord, or pull cord around sharp edges or corners.
Do not run vacuum cleaner over cord. Keep cord away
from heated surfaces.
Do not use extension cords or outlets with inadequate
current carrying capacity.
Turn off all controls before unplugging.
Do not unplug by pulling on cord. To unplug, grasp the plug, not
the cord.
Do not handle plug or vacuum cleaner with wet hands or operate
without shoes.
Do not put any object into openings. Do not use with any opening
blocked; keep free of dust, lint, hair, and anything that may reduce
airflow.
This vacuum cleaner creates suction and contains a revolving
brushroll. Keep hair, loose clothing, fingers, and all parts of body
away from openings and moving parts.
Do not pick up anything that is burning or smoking, such as
cigarettes, matches, or hot ashes.
Do not use without dust cup or filter in place.
Use extra care when cleaning on stairs.
Do not use to pick up flammable or combustible liquids such as
gasoline, or use in areas where they may be present.
Store your cleaner indoors in a cool, dry area.
Keep your work area well lighted.
Unplug electrical appliances before vacuuming them.
IMPORTANT SAFEGUARDS
When using an electrical appliance, basic precautions should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER.
WARNING
BEFORE YOU START
CHECK THE VOLTAGE
Before connecting the cleaner to an electrical supply, ensure that the voltage shown on the rating plate located beneath the
cleaner is of the correct voltage for your electricity supply. If it is not, do not use the cleaner but refer back to your dealer.
CONNECTING TO YOUR ELECTRICITY SUPPLY
Permanently connected to the cleaner is a mains supply (2-core) cable fitted with a non-rewirable plug incorporating a 13A fuse.
In the event of the fuse requiring replacement the fuse cover should be removed using a small screwdriver. The old fuse MUST be
replaced by a 13A ASTA approved BS1362 fuse or a BSI approved fuse. The cover must be replaced before the plug is used again.
In the event of loss of the fuse cover, replacements can be obtained from your Electrolux Retailers and must be of the same colour as
indicated by the coloured insert on the base of the plug.
If difficulty is experienced in obtaining a replacement, contact Electrolux Customer Services on 08706 055055.
In no circumstances must the plug be used without a correct fuse cover fitted.
If the plug that is fitted to your appliance is not suitable for your socket outlet, it must be cut off and the appropriate plug fitted.
Remove the fuse from the cut off plug.
The cut off plug should then be disposed of to prevent the hazard of shocks in case it should be plugged into a 13 amp socket in
another part of your home.
The wires in the mains cable of this appliance are coloured in accordance with the following code: Blue: Neutral. Brown: Live.
As the colours of the wires in the mains cable of this appliance may not correspond with the coloured markings identifying the terminals
in your plug, proceed as follows:
The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
If using a three-pin plug, do not make any connection to the terminal marked with the letter E or by the earth symbol or coloured green
or green-and-yellow. This cleaner is double insulated and no earth connection is necessary.
It is in your interest to ensure that the plug is correctly attached to the mains
cable. In case of doubt, consult a qualified electrician, as Electrolux cannot regard
the repair of faults on the plug connection as a service that can be given free
of charge under the terms of the guarantee.
WARNING
Proprietary carpet conditioning and air freshening materials
After using proprietary carpet conditioning powders, it is recommended that the
filters be changed. Some of these preparations contain substances which if left in the
vacuum cleaner for extended periods could damage the plastic mouldings which form
the structure of the cleaner.
Many air fresheners, household deodorants, sprays and polishes contain a highly flammable gas propellant.
Because of this, it is particularly important that these products are used strictly in accordance with the relevant manufacturer’s instructions.
It is essential that none of the above products are sprayed directly into the vacuum cleaner or any of its filters, hose assembly, dustbag
chamber or dust cup.
Thermal Cut Off
This vacuum cleaner has a special thermostat that protects the cleaner in case of motor overheating. If the cleaner shuts off, turn off
the switch and unplug the cleaner. Check the cleaner for a possible source of overheating such as a full dust cup or a clogged filter. After
the 60 minute period, plug the cleaner back in and push the on/off switch On (I). If the cleaner still does not run, please call Electrolux
Customer Care.
13
Fuse
Cover
Fuse
Blue
Brown
Cord Clamp
13 Amp Fuse
SAVE THESE INSTRUCTIONS
33
SERVICE
Should you require service on your Electrolux cleaner, please telephone Electrolux Customer Services on 08706 055055. Before
requesting service, please check whether your problem is covered under Service Checklist (see below).
New filter pads,brush rollers and drive belts can be obtained from Electrolux Retailers. If difficulty is experienced in obtaining
spares, please contact Electrolux on 08706 055055.
SERVICE CHECKLIST
If your cleaner will not operate, check the plug connection, plug fuse and mains fuse.
Never allow the dust cup to become so full that it impedes the air-flow, thus reducing the cleaning efficiency of the machine.
The character of household dust and its effect on the air-flow through the machine may vary considerably. Fluffy dust allows
air to pass through readily whereas fine powdery dust or proprietary cleaning powders, pack tightly in the dust cup, offering
greater resistance to air-flow and will reduce cleaning efficiency if the cup becomes overloaded.
Always store your cleaner and spare dust filters in a dry place.
Renew the filter pads three or four times a year. This is essential to ensure continued high filtration of dust particles.
Sucking up such items as stockings, clippings of cloth, sizeable pieces of paper, wrappings from cigarette packets or sweets
etc., may cause blockages in the cleaner. Electrolux regrets that the clearing of blockages cannot be regarded as service
that can be given free of charge, under the guarantee.
Never pick up hot cinders or lighted cigarette ends.
Make certain that your cleaner does not come into contact with water or any other liquid. It is not designed as a wet
pick up cleaner, and must never be used on damp carpets or wet floors.
Important - in the event of the mains supply cable of this vacuum cleaner requiring replacement, we recommend that this be
carried out by Electrolux Service Staff.
Spares
New filters and brush rollers can be obtained from Authorised Electrolux Dealers and electrical retailers. If difficulty is experienced
in obtaining spares please call us on 08706 055055 or visit our website at www.shop.electrolux.co.uk
GUARANTEE
This guarantee is in addition to your statutory and other legal rights.
This product is for household use only.
Electrolux products are carefully designed, manufactured, tested and inspected and, in consequence, we undertake to replace or
repair any part found to be defective in materials or workmanship, within one year of delivery to the original purchaser, free of charge.
You may be required to take the product to your nearest service provider if the product requires attention during the first year.
There are certain conditions which may invalidate this guarantee:
a. It is dependent upon the appliance being correctly installed and used in accordance with the Companys instructions under normal
domestic conditions within the United Kingdom or the Republic of Ireland.
b. Service at all times must be carried out by an Electrolux Service Representative or authorised agent.
c. The guarantee may be invalidated by unauthorised repair or modification of the appliance.
d. You may be charged by Electrolux if you call for an engineer to resolve a problem that we believe is covered in the instruction booklet.
(example: blocked/dirty filters)
Electrolux does not accept liability for all defects arising from neglect, misuse or accident. This guarantee excludes such normal wearing
parts as drive belts, brushes and filters as the life of these depends upon the amount and nature of use.
Proof of purchase will be required before service under guarantee is provided. Please call 08706 055 055 for assistance.
IMPORTANT:
For future reference we suggest you record the following details here, and keep the receipt with the handbook as proof of purchase.
Purchased from ____________________________________________________
Date purchased __________________Model no __________________________
101 Oakley Road, LUTON, BEDFORDSHIRE, LU4 9QQ
Features of the Electrolux vacuum cleaner and accessories supplied with it are protected in Great Britain and abroad by Patents or Registered
Designs.
This appliance conforms with the requirements of the amended E.E.C. directive No. 89/336/EEC relating to electromagnetic compatibility
(EMC) CE.
Electrolux, may introduce modifications to their product from time to time, and consequently the details given in this booklet are subject to
alteration without notice.
GUARANTEE
IMPOR
T
ANT INFORM
A
TION
HOW TO ASSEMBLE
Assemble completely before using.
1. Attaching or Removing Floor Nozzle.
Align the lock button on the floor nozzle neck with the
hole in the receiving tube on the main body. Push the
lock button and slide the floor nozzle into the main body
until it clicks into place. Push the lock button in and pull
on the floor nozzle to remove it from the main body.
2. Attach Handle Grip.
Align the lock button on the handle tube with the hole in
the handle grip. Push the lock button and slide the handle
into place
3. Attach handle tube to the cleaner.
Insert the end of the handle tube with the guide tabs into
the cleaner. Push the handle release button to get the
handle tube fully inserted. The handle is properly inserted
when you hear a click.
4
5
1
Off / Suction /
Brushroll Switch
Handle Grip
Handle Tube
Dust Cup
Cord Retainer
Cord Hooks
Receiving Tube
4. Store Cord (using cord hooks).
Pull the electrical cord down around the lower cord hook,
then wrap cord around upper and lower cord hooks. Fasten
plug to electrical cord to prevent unwinding.
5. Store Unit.
Push the telescoping handle release button to lower the
handle into its compact storage position. The handle is
locked down when a click is heard.
Dust Cup
Release Button
Handle Release
Button
Lock Button
Connector Pins
3
2
Brushroll
Clean Out
Port (Open)
4
QUICK REFERENCE
QUICK REFERENCE HOW TO ASSEMBLE
Locked Brushroll
Indicator
5
On/Off Switch
1
2
3
5
6
7
4
8
Lock
Position
HOW TO USE
ROUTINE MAINTENANCE
Empty Dust Cup
HOW TO USE
Power Switch
1. This vacuum has a 3-position switch. O is Off, I is “Suction Only,
and II is “Suction and Brushroll.
2. For bare floor cleaning use suction only (I). For carpet cleaning,
use suction and brushroll (II).
The nozzle allows for low profile cleaning. Airflow under the nozzle
automatically directs suction to the edges and corners for maximum
full width cleaning.
ROUTINE MAINTENANCE
The instructions in this booklet serve as a guide to routine
maintenance. To keep the cleaner operating at top efficiency empty
the dust cup and clean the filter after each use. To maximize cleaner
efficiency do not allow the dust cup to be filled past the bottom of
the filter.
Empty Dust Cup
CAUTION: Turn off the power switch and unplug the
electrical cord to service.
3. Push dust cup release button.
4. Pull the dust cup away from the main housing.
5. Rotate the dust cup lid counterclockwise to remove. The dust
cup filter comes out with the dust cup lid.
6. Empty the dust cup into a waste container. (To clean filter refer
to dust cup filter section.)
7. Put the lid back on dust cup. Be sure the gasket on the filter
bottom is centered in the inner tube and the lid is aligned correctly
on the cup. Rotate the dust cup lid clockwise until it locks.
8. Place the bottom of the dust cup in the main housing. Push the
top of the dust cup back into place until it locks.
6
Clean Dust Cup Filter
CAUTION: Turn off the power switch and unplug
the electrical cord to service.
Clean dust cup filter as necessary.
1. Remove dust cup.
2. Remove dust cup lid and filter assembly.
3. Shake and brush the dust and dirt from filter. If desired,
launder the filter by hand in warm water using a mild
detergent. Thelter may be washed up to 6 times. Air dry
thoroughly.
4. Replace filter in dust cup by twisting the dust cup lid firmly
into place to ensure proper filter performance.
5. Place bottom of dust cup in main housing. Push top of
dust cup back into place until it locks.
NOTE: The dust cup filter is not dishwasher safe.
Do not put in dishwasher.
NOTE: When vacuuming carpet fresheners or
cleaners, powder, plaster dust, or similar
fine substances, the dust cup filter will
require more frequent maintenance.
NOTE: Use only GENUINE ELECTROLUX
replacement filters, Code EF88.
PROBLEM SOLVING
Remove a Clog in the Base
This model has a clean-out port which allows access into the
bottom of the power nozzle in order to remove large debris that
has become lodged in the airway. (See page 3 for location.)
CAUTION: Turn off the power switch and unplug the
electrical cord to service.
1. On the bottom of the power nozzle, locate the transparent
Clean-Out Port Door located between the wheels. (See
page 3.)
2. Remove the port door by squeezing the latch at the back
of the nozzle and rotating the port door forward. No tools
are needed for this step.
3. Locate and remove clog from the power nozzle.
4. Reattach the clean-out port door by inserting the front edge
into position and rotating the door into the base until the
latch snaps into place. Ensure that the latch is secure. Do
not use the vacuum without first reattaching the clean-out
port door.
5. If needed, you may remove the power nozzle from the
main body of the cleaner to locate the clog in the neck of
the power nozzle.
3
4
2
5
ROUTINE MAINTENANCE
Clean Dust Cup Filter
PROBLEM SOLVING
Clean Out Port
Brushroll
Clean Out Port
(Open)
Latch
7
PROBLEM SOLVING
Automatic Brushroll Circuit Protector
This vacuum comes equipped with a brushroll circuit protector
which turns the brushroll off in the event of a stall situation. A
locked brushroll condition is indicated with the signal light on
the hood.
CAUTION: Turn off the power switch and unplug the
electrical cord to service.
1. Turn off the vacuum and unplug it.
2. Remove the obstruction from the brushroll.
3. Plug the cleaner back in and turn the vacuum on to
continue using.
4. Periodically remove hair and threads from the brushroll.
The symbol on the product or on its packaging indicates that this product may not be treated as household waste.
Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By
ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and
human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed informa-
tion about recycling of this product, please contact your local city office, your household waste disposal service or the shop
where you purchased the product.
Part No. 75428 (2/05)
Thank you for purchasing
an Electrolux cleaner.
Items in This Carton
Don’t Forget to Use
Genuine Electrolux parts
Caution: Damages caused by the use of non-genuine parts
are not covered by the Electrolux Guarantee.
If you experience any problems with your cleaner,
don’t struggle taking it back to the shop
Call our dedicated Customer Helpline
for help and advice on
08706 055055
Handle Grip
Handle Tube
Nozzle
Vacuum Cleaner
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Electrolux Z425 Series User manual

Category
Vacuum cleaners
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI