3D Systems 284107-00 User manual

Brand: 3D Systems

Model: 284107-00

Type: User manual

This manual is also suitable for

ProJet Cart Station

User Guide

ProJet

Cart Station

TABLE OF CONTENT

INTRODUCTION .............................................................................................................................................................................. 3

ABOUT THIS GUIDE ........................................................................................................................................................................ 3

COPYRIGHT .................................................................................................................................................................................... 4

IMPORTANT SAFETY INFORMATION ............................................................................................................................................ 5

SPECIFICATIONS and REQUIREMENTS ....................................................................................................................................... 6

FAMILIARIZATION ........................................................................................................................................................................... 7

FACILITY REQUIREMENTS ............................................................................................................................................................. 8

PREPARATION FOR WALL-MOUNT ............................................................................................................................................8-9

WALL-MOUNT INSTALLATION ..................................................................................................................................................... 10

TABLE-MOUNT INSTALLATION .................................................................................................................................................... 11

OPERATION ..............................................................................................................................................................................12-15

MAINTENANCE .............................................................................................................................................................................. 16

SERVICE and SUPPORT ............................................................................................................................................................... 17

SPARE PARTS ..........................................................................................................................................................................18-20

INTRODUCTION

Thank you for purchasing “ProJet® Cart Station. We pride ourselves in our ability to offer customers three dimensional printing

solutions. The 3D System team is condent your system will provide many years of service.

ABOUT THIS GUIDE

• Safety: Read prior to handling VisiJet® Materials or operating the printer. The safety sections inform you of handling the

material properly and avoid damage and injury when operating the printer. For more detailed material safety information,

refer to VisiJet® Material Handling Guide.

•

• System Requirements: Provides electrical requirements prior to plugging in your printer for operation.

•

• Familiarization: Provides a brief description of the Cart Station.

•

• Operations: Describe how the station functions.

•

• Error Messages: Denes the error messages you may see on the station’s display and provide the actions to take.

•

• Maintenance: List maintenance procedures which must be done to ensure optimum performance.

• Technical Support: List of contact numbers of sale and support personnel for your printer system.

proprietary information that is the property of 3D Systems, Inc. The licensed user, in the name of whom this document is registered

(the “Licensed User”) does not have the right to copy, reproduce, or translate this document in any way or to any media without the

prior written consent of 3D Systems, Inc. No copies of the document may be sold or given to any person or other entity.

ProJet®, the 3D logo and VisiJet® are registered trademarks of 3D Systems, Inc.

Improvements

3D Systems may (but shall not be obligated to) make improvements to this document from time to time. However, the Licensed

User acknowledges that at any time after the expiration of the date of issuance, 3D Systems may institute a periodic charge or fee

payable by the Licensed User in return for ongoing receipt of improvements. It is the responsibility of the Licensed User to pro-

vide 3D Systems with current information as to its name and address. The Licensed User also undertakes to notify 3D Systems

promptly in the event that it considers any of the data contained in this document to be incomplete or erroneous in any respect, in

connection with Licensed User’s particular use or generally.

FCC Notice

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in

a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used

in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment

in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his

own expense.

Changes or modications not expressly approved by 3D Systems could void your authority to operate this equipment.

Limitations of Warranty and Liability

This information is provided by 3D Systems for the convenience of its customers. It is believed to be reliable, but NO REPRESEN-

TATIONS, GUARANTEES, OR WARRANTIES OF ANY KIND ARE MADE AS TO ITS ACCURACY, FITNESS FOR A PARTICULAR

USE, OR THE RESULTS TO BE OBTAINED THEREFROM. The information is based in whole or in large part on laboratory work

and does not necessarily indicate performance in all conditions. Notwithstanding any information provided by 3D Systems or its

afliates, the customer remains fully responsible for determining which federal, state, or local laws or regulations, or industry prac-

tices are relevant to activities in which it engages, as well as assuring that those laws, regulations, or standards are complied with

under actual operating conditions, and 3D Systems undertakes no responsibility in these areas.

IN NO EVENT WILL 3D Systems BE RESPONSIBLE FOR DAMAGES OF ANY NATURE, INCLUDING SPECIAL OR CON-

SEQUENTIAL DAMAGES, RESULTING FROM THE USE OF OR RELIANCE UPON THIS INFORMATION. THE CUSTOMER

ASSUMES ALL RISK RESULTING FROM THE USE OF THIS INFORMATION. Customers use of the materials that follow is an ac-

knowledgment of its agreement to the foregoing. Any customer not wishing to be bound should return this material to 3D Systems.

Nothing contained herein is to be considered as permission, recommendation, nor as an inducement to practice any patented

invention without permission of the patent owner.

IMPORTANT SAFETY INFORMATION

SafetySymbolsandDenitions

Safety Guidelines

• Before using the printer and cart station, your company should have a safety program in place. The safety pro-

gram should:

• Label and point out hazardous equipment, materials, and procedures.

• Explain what to do in case of an emergency.

• Provide information about hazards of equipment and materials in the form of Material Safety Data Sheets or

Safety Data Sheet (MSDS / SDS). The MSDS / SDS are provided with all materials supplied by 3D Systems.

• Read and follow all station instructions.

• Follow all safety rules and heed all cautions and warnings in this guide.

• Do not use any material without reviewing the Material Safety Data Sheets/Safety Data Sheets (MSDS/SDS).

• Do not attempt to access, service, or adjust Cart Station components. Do not attempt to perform any mainte-

nance procedures unless specically trained to do so.

• Certied service personnel are those who completed the 3D Systems service training package and certied

to perform service tasks. Certication may occur at different levels, and service providers should only perform

tasks they are authorized and certied to complete.

• Disconnect the Umbilical cable before cleaning the cart or material cart.

• Do not remove any cart panels in an attempt to add or remove material.

• Do not energize the Cart Station if the Umbilical has been pinched or damaged.

• To prevent potential skin-irritation and sensitization due to contact with waste material, follow all guidelines

within Build Material Safety.

• Do not operate the Cart Station if the cart is:

• Being serviced

• Missing any protective panels

• Missing any hoses or hose ttings

Electrical Shock Hazard: High voltage electricity is accessible in the vicinity of this sign or behind the access

panel. High voltage can cause severe burns or death. Access panels are for service only and should be opened

only by certied service personnel or trained maintenance personnel.

Harmful Irritant Warning: Indicates that skin or eye irritation could result while exposed to a chemical composition.

Caution: Indicates something may happen that could cause loss of data, damage to equipment, or personal injury

Wear gloves when handling uncured VisiJet® build material.

Follow these safety guidelines when operating the station:

SPECIFICATIONS and REQUIREMENTS

Cart Station Properties

Cart compatibility ProJet ™ 6000, ProJet ™ 7000

MountingConguration Wall Mount / Table Mount

Screen Display 4 lines of text, 20 characters per line, Backlit

Screen Language English

User Interface 4 Momentary Push buttons

User Safety Emergency Stop (E-stop) provided

Screen Size (W x H) 3” by 1”

Pump Direction Print tray into cart

Cart Station Functions Heat, Stir, Pump, Heat & Stir, Stand-by

Dimensions (W x D x H) 12” x 6” x 12 1/4”

Weight 5.7 kg

Capacity Maintains one cart per Cart Station

Noise < 65 dB

Cart Umbilical Harting 42pin Cart plug, 3 foot, male

Electrical

Facility Electrical Requirements 100-240 VAC, 50 / 60 Hz w / grounded receptacle

Circuit Breaker Amps 5 Amps

Power Consumption 100 watts peak, 50 watts nominal

Amps 0.5 amps nominal, 1 amp max

Output Voltage (motor/heater) 24 volts DC

Fused Amperage (heater) 2.5 amps

Fused Amperage (motor) 0.3 amps

Power Cord 2 meter (6 foot) grounded IEC type (included)

Temperature Ranges

Material Temperature Range 20 - 40 degrees C, 28 nominal

Default Heater Temperature 35 deg. C for ProJet™7000, | 50 deg. C for ProJet™6000

Heater Temperature Range 20 - 50 degrees C

Ambient Room Temperature 20-26 degrees C (68 – 79 degree F)

Ambient Relative Humidity 20 – 50%

Cart Station User Interface

When pressed, station will stop running.

Used for different purposes depends of the current state:

• To cancel current routine and get back to the main menu.

If cancel used during “Settings setup” sequence at ANY

time - it will restore system settings saved into the buffer

before begging of the whole sequence.

• Reboot if system in the “HOLD” state.

• Access to “Service” screen (only from Main menu - press

and hold for 5 Sec).

Accept the set value and move to the next screen.

Alternated cursor in dual option menus or decrement value

Alternated cursor in dual option menus or increment value

User interface screen displays menus of cart station current

state.

D C B

FAMILIARIZATION

This Cart Station, (PN: 284107-00) is a wall or table mounted power supply to provide power to the material cart that is sup-

plied with the ProJet® 6000 / 7000. If the cart is removed from the printer, it can be connected to the Cart Station instead.

Once connected to the Cart Station, the cart will perform the following:

1. Pump material from the print tray to the cart until the tray is empty or the cart is full.

2. Heat the material to the proper temperature.

3. Stir the material at xed time intervals to keep the material homogeneous.

Each Cart Station will maintain one material cart. 3D Systems recommends proper material storage, as this is an important

factor of achieving the ne details and reliable material properties that the ProJet 6000/7000 can provide.

Control Box

Umbilical

Connector

Cord

Receptacle

ON / OFF

Switch

Umbilical

Holder

Table-Mount Bracket

If you choose to mount your station to the wall, the table mount

bracket attached to the cart station will need to be removed.

Required Tools: (not supplied): #1 Phillips head Screwdriver,

5mm Allen Wrench, T20 Torx plus driver

• Using a Phillips screwdriver, loosen the three (3) thumb-

screws and open front panel.

PREPARATION FOR WALL-MOUNT

Remove Table Mount Bracket

FACILITY REQUIREMENTS

Electrical Requirements

Facility Electrical Requirements 100-240 VAC, 50 / 60 Hz w / 15 amp. grounded receptacle

Temperature Ranges

Ambient Room Temperature 20-26 degrees C (68 – 79 degree F)

Ambient Relative Humidity 20 – 50%

Thumbscrews

• Using a T-20 torx plus driver, remove the two (2) m4 x10 torx screws securing the bottom of station to the table-

mount bracket. Loosen the two top screws and slide the station to clear the keyholes in stations. Lift station from

bracket and retain screws.

Two screws at the top

Two screws at the bottom

• Using a T-20, remove the two torx plus screws securing the umbilical holder to the table mount bracket. Retain screws

incase you may want to mount cart to a table in the future.

If you choose to mount your station to the wall, It is important to follow these steps to ensure that the station is mounted correctly

and the umbilical is in reach to the material cart without it being stressed.

Required Tools: (not supplied): Measuring Tape; Pencil for tick mark; Template that is supplied in this guide; #2 Phillips screw-

driver

• The Cart Station should be mounted so that a grounded wall 100-240 VAC / 50-60 Hertz, 15 amp receptacle is within reach of

the power cord. Before powering on the station, the grounding terminal connection to earth ground should be veried.

cm (42”)

FLOOR

cm (11”)

Two keyholes

Bottom of station

Two screw holes

11.03”

(280.2 mm)

7.48”

(190 mm)

• Using a 5mm Allen wrench, remove the two M6 screws from the bottom left corner of cart.

• Orient holder as shown and align holder holes to the screw holes at the bottom left corner of station. Install umbilical

holder using the two M6 screws that were removed to secure umbilical holder to the cart station.

• Using a measuring tape, measure a height of 42” from

the oor and up the wall; add a tick mark on the wall

indicating where the bottom of the station will be.

• Measure a height of cm (11”) from the tick mark and

up the wall; add another tick mark indicating where the

station’s two mounting keyholes will be.

• Measure a height of 11.03” (280.2 mm) and the width

of 7.48” (190 mm) from the screw holes center points to

the center point of keyholes. Add tick marks indicating

where the station’s mounting points will be.

WALL MOUNT INSTALLATION

• Install four anchors into the marked hole locations; the anchors should be ush

to the wall.

• Install two screws to the two top anchors. Leave a little gap between the anchor

and screw to install station.

Required Tools & Fasteners (not supplied): Phillips Screwdriver; Four (4) 6mm or 1/4” screws Anchors (anchors depend on

the wall type).

Anchors should be

ush to the wall

• Install station’s two upper keyholes (backside of station) onto the two upper screws.

• Turn the three thumbscrews counterclockwise to unlock the front cover and open cover.

Keyholes

Thumbscrews

• Align the stations’s two bottom holes to the two bottom pilot holes in wall and install two screws. Tighten

the upper and lower screws securely.

Install two screws

TABLE MOUNT INSTALLATION

If you choose to mount the cart station to a table, it is important that the table height is at least 37” to prevent the umbilical from hitting

the oor.

The Cart Station should be mounted so that a grounded wall 100-240 VAC / 50-60 Hertz, 15 amp receptacle is within reach of the

power cord. Before powering on the station, the grounding terminal connection to earth ground should be veried.

• Install the cart station table mount to the table as shown.

• Turn the two adjusting keys that are located underneath the table mount clockwise until the cart station is securely attached to

the table.

Two (2) Adjusting Keys

Powering ON the Cart Station

NOTE: Use only the UL listed IEC type power cord that is supplied with the Cart Station.

• Connect power cord to the power receptacle located on the right side of station and into facility’s receptacle. Ensure the

receptacles meet the electrical requirements noted in “Facility Requirements” section.

• Connect station umbilical connector to the material cart connector. It is acceptable to connect the umbilical to the cart

when the station is ON.

• Ensure that the print tray is connected to the cart before you start the cart station.

• Power on cart station, the user interface screen will display.

Plug Power Cord into

Station Receptacle

Power Switch

Connect umbilical con-

nector to the material

cart’s connector

User Interface Screen

OPERATION

NOTE: The material requires 24 hours to heat prior to use. Avoid heating material over 72 hours; doing so will

cause the material to age.

NOTE: Before every use, verify the umbilical plug and connector are clean before connecting.

Caution: Never disconnect the station from the cart while it is stirring or pumping. First, cancel the operation

in the User Screen or turn off the power switch before disconnecting from cart.

Once powered up, the system will go through the

“System Check” that includes a 24 volt power supply

check, controller hardware check and cart connection

check.

• If cart is connected and all cart’s sensors are

within the expected range “Cart is detected” will

appear on the display screen.

• If cart is connected, but if any of the sensors are

out of range or not connected, an Error will occur

and will halt the system. The error message will

display the cause of the halt on the screen.

• If cart is not connected, an Error message will

display “No Cart detected.” This system state will

not halt the system.

System Check

After the System Check, the “Main Menu Screen” will

display along with the “System settings” options and

status of the cart. RUN (6000 Cart)” or “RUN (7000

Cart)” will be displayed to indicate if it is in 6000 Cart or

7000 Cart mode.

Main Menu Screen

ProJet 6000 / ProJet 7000 Cart setting Menu

System Settings

• Mixing ON / Mixing OFF

• Mixing ON Time

• This could be adjusted in 10 percent incre-

ments. Setting it for example to 10 percent

will run mixing motor for 1 minutes every 10

minutes.

Setting will be saved to memory after LAST settings is

conrmed. Selecting “Cancel” at anytime will quit setup

routine. The main screen will display and restore settings

that have automatically been saved BEFORE beginning

“System Settings” cycle.

When you select “RUN,” the following sequence will begin:

RUN

• Fluid’s Valve Motor will be ON for 15 seconds and

is waiting to detect end of the travel.

• If valve is in the correct position and ready, it will con-

tinue to the next step.

• Material will be transferred to the cart until:

• Cart is full, or

• Pump is running for 2 hours (time out)

• Until there is no more material to transfer to the

cart.

• If cart is completely empty, pump material until

3 minutes time-out or level is OK; it will con-

tinue the rest of the pumping routine.

• There is a minimum level required in the cart in order to be able to heat and mix the material. Currently this

level is just below 1/4 of the cart. If the level is more than the minimum “Status” will display. If there is no

more resin to transfer and level in the cart is still too low, the system will display an error and it will be halted.

Goes ON and OFF in

Sync with Heater

• RUN status screen:

• Heater and Mixer will run with previously programmed parameters if there is minimum level of material in

the cart.

• Current material temperature; minimum material level OK, cart full and programmed settings for Mixing and

Heating ON/OFF/IDLE will be displayed

Cart Status

Resin Temperature

System will periodically check the hardware and con-

nections to the cart and could result in the following

errors:

Errors

• 24V power supply out of range.

• Emergency Stop Button is pressed.

• Material level sensor is disconnected or non-operational.

• Material thermistor is disconnected or non-operational.

• Heater thermistor is disconnected or non-operational.

• Not enough material in the cart after trying to pump material and timed out.

• Valve motor is disconnected or non-operational.

MAINTENANCE

Before attempting to clean away any liquids or debris that may come into contact with the cart station, turn off the

power, unplug the Umbilical, and unplug the station’s power cord.

The Cart Station housing may be cleaned with a towel that has been dampened with detergent and water. How-

ever, the station is not water or air tight, so care must be taken to ensure no water or other uids enter through

the ventilation holes. Any aerosol, water, or paint sprays should be directed away from the station. Contact 3D

customer support if further cleaning is required.

Keep the Umbilical plug and connector clean.

When not in use, the Umbilical should be placed in the holder, to keep it out of the way.

Keep Umbilical connector away from liquids, grease, dirt, and dust.

SERVICE AND SUPPORT

For information, questions, or comments about your ProJet®3-D printer system(s), VisiJet® materials, or request ser-

vice, please contact a 3D Systems Customer Service or Sales Representative nearest you.

3D Systems

333 Three D Systems Circle

Rock Hill, SC 29730 USA

tel: 803.326.4080

fax: 803.324.8810

toll free: 800.889.2964

E-mail: [email protected]

www.3dsystems.com

NYSE: DDD

• North & South America: [email protected]

• AsiaPacic: [email protected]

• Europe/Middle East/Africa: [email protected]

How to Order Parts

• New and refurbished parts made by 3D System’s manufacturer are used when performing warranty repairs and

in building replacement parts and systems. Refurbished parts and systems, are parts or systems that have been

returned to 3D Systems, some of which were never used by a customer. All parts and systems are inspected and

tested for quality. Replacement parts and systems are covered for the remaining period of the limited warranty for

the product you bought. 3D Systems owns all parts removed from repaired products.

•

• To order replacement parts, contact 3D Systems Customer Service Support or contact your local reseller.

•

• When contacting 3D Systems Customer Service Support, have your serial number available to give to customer

support.

SPARE PARTS

No. Part Number Description Qty.

1 19816-107-00 Scr, M6x1.0x20, Soc, Ss 2

2 2850-00511-100 Washer,M6 2

3 284667-00 Cbl Assy, Umbilical 1

4 284668-001 Umbilical Holder 1

SPARE PARTS

No. Part Number Description Qty.

1 284382-00

Front Panel Label

2 20819-106-00

Switch,Emerg Stop,16Mm

3 283246-00

Label, Ring, E-Stop Button, 16MM ID, 43MM OD

4 284352-00

Push button, 18mm, SPDT, Momentary, Black

284661-00 Enclosure Cover

284670-00 Screen Shield

284351-00 LCD Kit, 4 X 20, Backlit, Ribbon Cable

282949-00 SCR, PHPH, M2.5 X 8, SS

284397-00 Loop Clamp, 1/2”, Nylon

201989-00 M4 NUT W/TOOTH

19816-136-00 SCR,M3X.5X8,SOC,SS

282259-00 HINGE

273349-00 WASHER, M3, 9mm OD, SS

18116-101-00 NUT,M3,.5,HEX,SS

SPARE PARTS

No. Part Number Description Qty.

1 284366-00

EC Inlet C20, Front Side, QC Terminal, 16A, 250V

2 18115-101-00

Scr, M3x0.5x10, Flt, S, Zc

284367-00 Circuit Breaker, Thermal, 2P, 240V, 5A

284350-00

201989-00 M4 Nut W/Tooth

19816-136-00 Scr,M3x.5X8,Soc,Ss

284664-00 Thermal Pad

284358-00 Interface PCB Assembly

284663-00 Heatsink, PCB

284353-00 PS, Switching, 320W, 24V, 85-264VAC

284662-00 Hardware Panel

19816-101-00 Scr, M4x0.7x6, Soc, Ss

284669-00 Enclosure Box

Page is loading ...

3D Systems 284107-00 User manual

Brand: 3D Systems

Model: 284107-00

Type: User manual

This manual is also suitable for

ProJet Cart Station

Download PDF

report

3D Systems 284107-00 User manual

This manual is also suitable for

3D Systems 284107-00 User manual

Related papers

Other documents