IMPORTANT: Read the Installaon Requirements secon above prior to installing the Push Buon.
You Will Need:
Control-R™ Push Buon
Control-R™ Module
Control-R™ Push Button Installation Instructions
Instrucons
Installaon Requirements
IMPORTANT: You have 5 minutes to pair the Push Button with the Control-R™ Module before Pairing Mode times out. If
Pairing Mode times out, you must repeat the steps below.
This document provides instrucons on installing the Rinnai Control-R™ Push Buon, which works with Rinnai’s Control-R™
Module to operate the Rinnai Tankless Water Heater recirculaon system. The Push Buon mounts near the point of use (such as
a kitchen faucet or bathroom sink) and acvates the recirculaon system. The recirculaon system will deacvate aer ve
minutes from iniaon or when the water has reached the set temperature. The Push Buon is only compable with Rinnai
Tankless Water Heaters featuring Rinnai Circ-Logic™. Follow all instrucons carefully to ensure proper performance.
On the Control-R™ Module, press and hold down the “Connect” button until
the LED light turns green. Then, release the button.
On the Push Buon device, press and hold down the buon unl the buon
ashes three mes. Then, release the buon.
The Control-R™ Module LED ashes green and then turns to the previous
mode (Blue = connected to Internet; Red = not connected to Internet).
The Push Buon is now paired with the Control-R™ Module.
Part #
RWMPB01
Prior to installaon, determine the best locaon for the Push Buon. Rinnai recommends installing the Push Buon near a
water xture that will be used frequently, such as a kitchen faucet or bathroom sink.
The Push Buon works in conjuncon with the Control-R™ Module. The Control-R™ Module must be installed and funconing
properly before installing the Push Buon.
1. Remove the Push Buon cover by pressing both sides of the boom plate and liing the cover.
2. Pair the Push Buon with the Control-R™ Module (called Pairing Mode) by following the steps below.
LED
Connect buon on
Control-R™ Module.
NOTE: If the recirculang pump has recently been acve and the recirculaon loop is sll warm, there may be a delay in pump
acvaon. To minimize any delay in pump acvaon, set the Rinnai Tankless Water Heater to Comfort Mode. Refer to the
“Recirculaon Mode” secon in the Tankless Water Heater Installaon and Operaon Manual for more informaon on Comfort
Mode.
Push Buon LED
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED
OPERATION
©2016 Rinnai America Corporaon. Rinnai America Corporaon connually updates materials, and as such, content is subject to change without noce.
Local, state, provincial, federal and naonal fuel gas codes must be adhered to prior to and upon installaon.
100000422(01)
9/2016
3. Replace the cover on the Push Buon device.
4. Determine a locaon for the Push Buon. Rinnai recommends installing the Push Buon near a water xture that will be used
frequently, such as a kitchen faucet or bathroom sink.
5. Remove the adhesive strip from the back cover and rmly press the body of the Push Buon device against the locaon
surface to allow the adhesive to take hold.
Operaon
Press the Push Buon to acvate the Rinnai Tankless Water Heater recirculaon system. The recirculaon system will deacvate
aer ve minutes from iniaon or when the water has reached the set temperature.
NOTE: If the recirculang pump has recently been acve and the recirculaon loop is sll warm, there may be a delay in pump
acvaon. For further informaon, refer to the “Recirculaon Mode” secon in the Tankless Water Heater Installaon and
Operaon Manual.
Remove adhesive strip
6. Installaon and pairing of the Push Buon is complete.
Restore Factory Sengs
To restore the Push Buon sengs to a fresh state, remove the two Push Buon baeries. Wait a few seconds and then reinsert
the baeries while pressing down on the Push Buon. Connue to press down on the Push Buon for an addional three seconds
aer the baeries have been inserted.
-
1
-
2
Rinnai RWMPB01 Installation guide
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Rinnai RWMMS01 Installation guide
-
Rinnai RUR160EP Installation guide
-
Rinnai RSC199iP User manual
-
Rinnai REU-NP3237FF-US-N Installation guide
-
-
-
Rinnai Sensei RUR199i Installation guide
-
Rinnai REU-N2530WC-US-P Operating instructions
-
Rinnai REU-N3237W-US-N Operating instructions
-