2. Vehicles & accessories
  3. Motor vehicle accessories & components
  4. Motorcycle Accessories
  5. Triton Systems
  6. Propane
Propane

Triton Systems Propane Owner's manual

  • Hello! I am an AI chatbot trained to assist you with the Triton Systems Propane Owner's manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • Where can I find the 'Display' connector on the Triton Systems Propane mainboard?
    How do I connect the Mainboard Power Harness to the DIN Rail?
    How do I connect the Modem Power Cable to the DIN Rail?
    How do I install the Control Panel Assembly?
    How do I secure the display cable to the edge of the door frame?
Propane Pump Payment Module
Register Data Cable,
Main Board Power Harness,
Modem Power Cable
& Control Panel Installation
07103-00159 Rev. B May, 20, 2015
Corporate Headquarters:
21405 B Street
Long Beach, MS 39560
Phone: (800) 259-6672
Fax: (228) 868-9445
COPYRIGHT NOTICE
© 2015 Triton. All Rights Reserved. TRITON logo is a
registered trademark of Triton Systems of Delaware, LLC
P P P M
2
Document Updates
Rev A...........................Original June 17, 2014
Rev. B..........................Updated Control Panel Assembly Installation May 20, 2015
Contents
Register Data Cable Installation............................................................................3
Mainboard Power Harness.....................................................................................7
Modem Power Cable...............................................................................................8
Control Panel Assembly Installation.....................................................................9
P P P M
3
Register Data Cable Installation
1. Remove the Calibration Screw on the right side of the Register. Set it aside for reinstallation.
NOTE: failure to remove the calibration screw prior to removing the register face could result in damage to the
register.
2. Remove the ten screws from the Register face. Open the Register carefully and tilt the face
plate down. Set the screws aside for reinstallation.
P P P M
4
3. Plug the register cable end into port J8 “MCR” on the docking board.
4. Route the cable around the right side of the Register to the rear securing the cable in the two cable clips.
Continue routing the cable into the rear of the Register as shown.
P P P M
5
5. Install the individual wires into connector J2 as follows:
Black= Screw Terminal 4
Red = Screw Terminal 5
Green= Screw Terminal 6
6. Carefully reinstall the Register face ensuring no wires have been pinched. Reinstall the 10 screws to secure the
face plate.
P P P M
6
7. Reinstall the Calibration Screw on the right side of the Register.
P P P M
7
Mainboard Power Harness
Connecting DC Power to the DIN Rail
1. Route the black/red Mainboard Cable from the docking board harness to the DIN rail. Connect the black wire
to a DC ground terminal. Tighten the screw to secure the wire in place.
2. Connect the red wire to a DC +5V terminal. Tighten the screw to secure the wire in place.
P P P M
8
Modem Power Cable
Connecting DC Power to the DIN Rail
1. Route the black /yellow Modem Power Cable from the modem board to the DIN Rail. Connect the black wire
to a DC Ground Terminal. Tighten the screw to secure the wire in place.
2. Connect the yellow wire to a DC +15V (or +12V) terminal. Tighten the screw to secure the wire in place.
P P P M
9
Control Panel Assembly Installation
1. Remove all blue tape securing the cables and the hinge bracket during shipment. Plug the 2 cables taped to the
card reader into the top of the card reader.
2. Attach the Control Panel to the unit with the four screws supplied. Ensure the cables are not pinched.
P P P M
10
3. Remove the cover from the back of the display by removing the nut holding it in place. Remove the cover
over the main board by liing the knob and sliding it back.
4. Locate the “Display” connector on the mainboard. Gently li the connector to the “open”position. Fully seat
the display cable in the connector, with the blue side facing the control panel. Close the connector ensuring the
cable stays fully seated.
Closed connector
Open connector
Open connector with seated cable
Closed connector with seated cable
P P P M
11
5. Starting at the back of the display, fold the display cable back over the top of the display about 1 1/2”. en fold
under itself as shown.
NOTE: Do not make sharp creases or damage could occur.
6. Fold the cable back under again as shown.
NOTE: Do not make sharp creases or damage could occur.
P P P M
12
7. Tape the cable in the two places shown.
8. Reinstall the display cover and secure it with the nut removed in step 3.
P P P M
13
9. With the door fully open, secure the display cable to the edge of the door frame with 1 piece of tape.
10. Carefully open and close the door several times to ensure the display cable is not being pinched or rubbing
against any item.
P P P M
14
11. Route the bundle of cables through the right front cable clip as shown. Plug the Mainboard Power Discon-
nect Harness connector into the Mainboard Power Harness cable from the mainboard as shown.
12. Secure the ground eyelet to the tray with the supplied screw as shown.
P P P M
15
13. Plug the Card Reader RJ45 cable connector into the port on the mainboard labeled “Card Reader”. Plug the
keypad RJ45 cable connector into the port on the mainboard labeled “Keypad”.
14. Plug the display power cable into the mainboard port labeled “Display”.
15. Reinstall the docking board cover.
Keypad Port Card Reader Port
/