HP RP9 Integrated 2x20 Display BTM w/Arm Installation guide
- Type
- Installation guide
This manual is also suitable for
- RP9 G1 Retail System Model 9015
- RP9 G1 Retail System Model 9015 (ENERGY STAR)
- RP9 G1 Retail System Model 9015 Base Model
- RP9 G1 Retail System Model 9018
- RP9 G1 Retail System Model 9018 (ENERGY STAR)
- RP9 G1 Retail System Model 9018 Base Model
- RP9 G1 Retail System Model 9115
- RP9 G1 Retail System Model 9118
- RP9 Integrated 2x20 Display Top w/Arm
Installation Instructions
HP RP9 Integrated 2x20 Top
Mount and Bottom Mount
Customer Facing Displays
(CFDs)
© Copyright 2016 HP Development Company, L.P. The information contained
herein is subject to change without notice.
Printed in
First Edition: February 2016
*843782-001*
843782-00 1
Before you begin
1. Save all files and shut down the computer properly through the
operating system, and then turn off any external devices.
2. Disconnect the power cord from the electrical outlet and disconnect
any external devices.
WARNING! To avoid the risk of serious injury or damage to the
computer, ensure that the computer’s AC power cord is unplugged
from the AC outlet at the wall before installing this product. Failure
to do so may expose you to the risk of electric shock.
WARNING! To reduce the risk of personal injury from hot surfaces,
allow the internal system to cool before touching.
CAUTION: Static electricity can damage the electronic components
of the computer or optional equipment. Before beginning this
procedure, ensure that you are static-free by briefly touching a
grounded metal object.
NO TE: For regulatory and safety notices, refer to the Product
Notices included with your product.
Product support
For the online access to technical support information, self-solve tools,
online assistance, community forums or IT experts, broad multivendor
knowledge base, monitoring and diagnostic tools, go to
www.hp.com/support
.
NOTE: If you need help preparing your computer model for this
installation, refer to the documentation provided with the computer,
or go to www.hp.com/support to locate the manual for your model.
Installing the top mount CFD
You must install the top mount CFD in the top USB port on the RP9 display
head. Before installing the CFD, you must remove the display head rear
cover and the top port cover.
1. Press the two latches on the display head rear cover outward 1.
Slide the rear cover up, and then lift it off the display head 2.
2. Remove the two screws that secure the top port cover 1, and then
pull the port cover off the display head 2.
NOTE: You may need to gently loosen the port cover from inside of
the screw holes with a flat screwdriver.
3. Align the tabs on the display head rear cover with the slots on the
display head. Place the cover on the display head, and then slide the
cover down so that it snaps in place.
4. Remove the cover from the CFD arm by pulling back the top of the
cover 1 and then the bottom of the cover. Insert the USB connector
on the CFD into the USB port 2, and then secure the CFD with the
screw provided 3. Replace the arm cover 4 by snapping the top of
the cover onto the arm and then the bottom of the cover.
5. Reconnect the power cord and any external devices, and then turn on
the computer.
Removing the top mount CFD
Remove the cover from the CFD arm by pulling back the top of the cover 1
and then the bottom of the cover. Loosen the screw that secures the CFD
to the display head 2, press in the two tabs on the sides of the CFD arm 3,
and then slide the CFD out of the USB port 4.
Installing the bottom mount CFD
The bottom mount CFD must be installed on the base of the RP9 stand.
1. Lay the RP9 face down on a flat surface covered by a soft clean cloth.
2. Slide the CFD bracket onto the underside of the base 1, and then
secure the bracket with the screw 2.
3. Route the CFD cable up through the center hole in the base and
connect it to a USB port on the rear of the display head.
4. Reconnect the power cord and any external devices, and then turn on
the computer.
Documentation feedback
HP is committed to providing documentation that meets your needs. To
help us improve the documentation, please send any suggestions,
comments, or errors to doc.fee[email protected]. Include the document title
and part number (located near the barcode) when submitting your
feedback.
Top Mount CFD
Bottom Mount CFD
-
1
HP RP9 Integrated 2x20 Display BTM w/Arm Installation guide
- Type
- Installation guide
- This manual is also suitable for
-
- RP9 G1 Retail System Model 9015
- RP9 G1 Retail System Model 9015 (ENERGY STAR)
- RP9 G1 Retail System Model 9015 Base Model
- RP9 G1 Retail System Model 9018
- RP9 G1 Retail System Model 9018 (ENERGY STAR)
- RP9 G1 Retail System Model 9018 Base Model
- RP9 G1 Retail System Model 9115
- RP9 G1 Retail System Model 9118
- RP9 Integrated 2x20 Display Top w/Arm
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
HP RP9 G1 Retail System Model 9018 Base Model Reference guide
-
HP RP9 2x20 LCD Top Mount without Arm Installation guide
-
-
HP Value Serial/USB Receipt Printer II Configuration Guide
-
-
HP Engage Flex Pro-C Retail System Configuration Guide
-
-
HP Engage One All-in-One System Model 141 Reference guide
-
-
HP Engage One Pro AIO System (9UK26AV) User guide
Other documents
-
Tadiran Telecom Coral FlexiCom 6000 Installation Procedure And Hardware Reference Manual
-
Sony CFD-Z125 Operating instructions
-
-
-
-
-
Sony CFD-F17CP Operating instructions
-
Sony CFD-S300 User manual
-
Sony CFD-S250L User manual
-
Sony CFD-S550L User manual
