Workzone GT-DC-02 User manual

Brand: Workzone

Model: GT-DC-02

Type: User manual

Workzone GT-DC-02: Below you will find brief product information for Workzone GT-DC-02. The Workzone GT-DC-02 digital caliper gauge is a versatile and easy-to-use measuring tool that is perfect for a variety of applications. With its 0.01 mm resolution, the GT-DC-02 can measure objects with a high degree of accuracy. The caliper gauge also features a large, easy-to-read LCD display, inch/mm conversion, and a zero gauge function. The GT-DC-02 is powered by a single 1.5 V button cell battery, and it comes with a protective case for storage.

IRE

AFTER SALES SUPPORT

[email protected]00800 / 4467 5888

GB 0800 / 328 6020

MODEL: GT-DC-02, 02/13, E45316

DIGITAL

CALIPER GAUGE

MANUAL

2 3

AFTER SALES SUPPORT 0800 / 328 6020 [email protected]

00800 / 4467 5888

GT-DC-02, 02/13, E45316

AFTER SALES SUPPORT 0800 / 328 6020 [email protected]

00800 / 4467 5888

GT-DC-02, 02/13, E45316

Scope of delivery

• Digital caliper gauge

• Cell battery 1.5 V

• Case

• Operating instructions

• Warranty card

Technical data

Resolution: 0.01 mm

Power source: 1 x cell battery 1.5 V , LR44, 19 μA

Measurement speed:  1.5 m/s

Operating temperature: 0 ~ + 40° C

Relative humidity: < 80 %

Storage temperature: -10° C ~ +60° C

As our products are constantly being further developed and

improved, design and technical changes are possible.

Table of contents

03 Scope of delivery

03 Technical data

04 Assembly diagram

05 Safety instructions

06 Functions

06 Maintenance/Storage

07 Use

08 Insertion of the battery

09 Instructions for batteries

11 Fault rectification

12 Measurements

13 Support table

15 Environmental protection/disposal

15 Conformity declaration

16 Warranty

19 Warranty card

4 5

AFTER SALES SUPPORT 0800 / 328 6020 [email protected]

00800 / 4467 5888

GT-DC-02, 02/13, E45316

AFTER SALES SUPPORT 0800 / 328 6020 [email protected]

00800 / 4467 5888

GT-DC-02, 02/13, E45316

Assembly diagram

1. Staged measuring surface 9. Depth bar

2. Inner measuring surface 10. Outer measuring surface

3. LCD display 11. Power on and off

4. Safety screw switch (ON/OFF)

5. Button cell (1.5 V) 12. Zero gauge (ZERO)

6. Battery lid 13. Switch for metric / inches

7. Slider (mm/inch)

8. Protective cover 14. Fine-tuning wheel

OFF ZERO

mm/inch

12 3 4 56 7 8 9

11 12 13 14

Safety instructions

• Injury hazard: The measuring edges are sharp and pointed!

Therefore, only hold the measuring device on the handles.

• Do not let children play with the measuring device. They can

injure themselves on the sharp measuring edges or swallow the

battery/battery compartment lid.

• Measure very carefully on sensitive surfaces, in order to avoid

leaving scratch marks.

• Do not connect any voltage to any part of the digital caliper

gauge (e.g. for engraving with an electric pen), as the switch

could otherwise be damaged.

• The digital caliper gauge is designed for private household use.

It is unsuitable for use in workshops, jewellery shops, etc.

6 7

AFTER SALES SUPPORT 0800 / 328 6020 [email protected]

00800 / 4467 5888

GT-DC-02, 02/13, E45316

AFTER SALES SUPPORT 0800 / 328 6020 [email protected]

00800 / 4467 5888

GT-DC-02, 02/13, E45316

Functions

1. The zero setting in any position simplifies stage measurements.

Press the zero gauge (ZERO) in order to define the zero point.

This enables difference measurements (negative measurements

are displayed with a „- “).

2. Inch/mm conversion in any position. Press the mm/inch key in

order to display the measurement result in a different unit.

3. For very precise measurements, the caliper gauge can be

operated particularly precisely using the fine-tuning wheel.

4. Automatic and manual power switch-on/switch-off.

Maintenance/Storage

1. Prior to use, clean the surface of the measuring scale with a dry

and clean cloth (or a light cleaning oil). Protect the measuring

scale from watery liquid.

2. Only clean with a dry cloth and some cleaning oil; do not use

any water, solvent or abrasive detergent.

3. Remove the battery if the instrument is not being used for a

longer period of time.

4. Preferably store the caliper gauge in the case in order to provide

optimum protection.

Use

1. Preparation:

(1) Wipe of the surface of the measuring scale and clean the

measuring surfaces.

(2) Loosen and move the safety screw, check the ease of movement

over the entire measuring range.

(3) Insert battery as described on page 8.

(4) Switch on device and check whether the LCD display and all keys

function faultlessly.

2. Measurement:

(1) Press the On/Off key in order to switch on the power. The device is

also switched on by activating the caliper gauge.

(2) Press mm/inch key in order to select the required unit of measure.

(3) Move the slider until the outer measurement surfaces touch

lightly, then press the zero gauge (ZERO) in order to start the

regular measurement. With the safety screw, you can fix the

caliper gauge in order to ensure the measurement result.

8 9

AFTER SALES SUPPORT 0800 / 328 6020 [email protected]

00800 / 4467 5888

GT-DC-02, 02/13, E45316

AFTER SALES SUPPORT 0800 / 328 6020 [email protected]

00800 / 4467 5888

GT-DC-02, 02/13, E45316

(4) Press the On/Off key in order to switch off the power; if the slider

is no longer used after the end of the measurements, the display

will switch off after approx. 4-5 minutes.

Inserting the battery

An abnormal display (flashing numbers or no display at all)

indicates a low battery voltage and the battery must be

replaced. Remove the battery lid in the direction of the arrow

and insert the battery or replace a used battery with a new one.

When inserting, pay attention to the correct polarity, the positive

terminal of the battery must be pointing upwards. Close the lid

again after inserting the battery. If the battery supplied with the

product does not work correctly (e.g. the voltage is low due to

being stored for too long), please contact the supplier.

Note:

1. After inserting the battery, the caliper gauge requires several

seconds (approx. 5-6 seconds) in order to set itself. The caliper

gauge can only be switched on again after the end of the setting

process.

2. Reset the zero point of the measurement after replacing the

battery.

Instructions for batteries

• Never attempt to recharge non-rechargeable batteries.

Explosion hazard!

• Keep batteries away from children, do not throw them into fire,

do not short-circuit batteries and never dismantle batteries.

• Immediately contact a doctor, if a battery has been swallowed.

• Clean the battery and device contacts prior to insertion, if

required.

• Immediately remove depleted batteries from the device.

Increased leakage hazard!

• Do not expose batteries to any extreme conditions, e.g. on

radiators, direct sunlight! Increased leakage hazard!

• Failure to comply with this could result in batteries being

discharged beyond their final charge voltage and leaking.

Remove batteries immediately, in order to avoid damage.

10 11

AFTER SALES SUPPORT 0800 / 328 6020 [email protected]

00800 / 4467 5888

GT-DC-02, 02/13, E45316

AFTER SALES SUPPORT 0800 / 328 6020 [email protected]

00800 / 4467 5888

GT-DC-02, 02/13, E45316

• Avoid contact with eyes or skin. Immediately rinse areas

affected by the battery acid with plenty of clean water and seek

medical advice.

• Remove the batteries from the device in the case of longer

periods of disuse.

Battery disposal

• Batteries and rechargeable batteries are not permitted to be

disposed of with household waste!

• Every consumer is legally obligated to submit batteries and

rechargeable batteries to the collection centre of his local

authority, district or to retailers. All batteries and rechargeable

batteries can thereby be disposed of in an environmentally

friendly manner.

Batteries and rechargeable batteries containing harmful

substances are identified with this symbol and with

chemical symbols (Cd for cadmium, Hg for mercury, Pb

for lead).

Fault rectification

Fault

Flashing display

No display

Frozen or flashing

display

Possible cause

Low voltage

1. Low voltage

2. Loose connection

Random fault in

the circuit

Solution

Replace batteries

1. Replace batteries

2. Readjust battery

Remove battery

and reinsert again

after one minute

CAUTION:

In the event of an electrostatic discharge on the housing, the

display can reset or an incorrect value can be displayed. In this

case, the measurement must be repeated. For this, switch the

device off and on once and carry out the zeroing by pressing the

zero gauge (ZERO) key.

12 13

AFTER SALES SUPPORT 0800 / 328 6020 [email protected]

00800 / 4467 5888

GT-DC-02, 02/13, E45316

AFTER SALES SUPPORT 0800 / 328 6020 [email protected]

00800 / 4467 5888

GT-DC-02, 02/13, E45316

Measurements

a) Outer measurement b) Depth measurement

c) Inner measurement d) Staged measurement

a) b) c) d)

Tip

Use the fine-tuning wheel for precise measurements.

It simplifies the precise setting of the caliper gauge.

Support table

Practical support table for cutting threads (also see the back of

the caliper gauge):

Column 1: Screw size

Column 2: Thread pitch

Column 3: Min. drill hole diameter

Column 4: Matching standard drill size

Metr. ISO

Nenn

Screw

ext.

extr.

Ø mm

Stg

Thread

Pas

Paso

Kern

Hole

int

núcleo

Ø mm

Bohr

Drill

mèche

broca

Ø mm

3 0,5 2,46 2,5

4 0,7 3,24 3,3

5 0,8 4,13 4,2

6 1 4,92 5

8 1,25 6,65 6,8

10 1,5 8,38 8,5

12 1,75 10,11 10,2

16 2 13,84 14

20 2,5 17,29 17,5

14 15

AFTER SALES SUPPORT 0800 / 328 6020 [email protected]

00800 / 4467 5888

GT-DC-02, 02/13, E45316

AFTER SALES SUPPORT 0800 / 328 6020 [email protected]

00800 / 4467 5888

GT-DC-02, 02/13, E45316

Environmental protection/

disposal

In the interest of the environment, dispose of the caliper

gauge properly. Do not throw the caliper gauge into

household waste, but rather, submit it to a collection

centre for electrical waste.

Remove the battery beforehand and dispose of it properly in a

collection container for batteries.

The packaging materials are also raw materials! Therefore,

submit them for recycling. Your responsible local authority will

inform you about addresses and opening times of collection

centres.

Conformity declaration

The conformity of the product with the prescribed standards is

guaranteed.

The complete conformity declaration can be found on the

Internet at www.gt-support.de.

Whitworth

Ø in Gg/in Ø mm Ø mm

1/4 20 4,72 5,0

5/16 18 6,13 6,4

3/8 16 7,49 7,7

1/2 12 9,99 10,25

5/8 11 12,92 13,25

3/4 10 15,8 16,25

7/8 9 18,61 19

1 8 21,34 21,75

16 17

AFTER SALES SUPPORT 0800 / 328 6020 [email protected]

00800 / 4467 5888

GT-DC-02, 02/13, E45316

AFTER SALES SUPPORT 0800 / 328 6020 [email protected]

00800 / 4467 5888

GT-DC-02, 02/13, E45316

Warranty

Model: Digital caliper gauge

The appliance has been manufactured with the greatest care.

The warranty period is three years from the date of purchase.

Please retain the sales receipt as proof of purchase as without it

the warranty claim cannot be processed.

During the warranty period, the sales receipt and the completed

warranty card with a description of the fault must be returned

once you have contacted the service centre by phone. A new

appliance will be returned.

This warranty is in addition to your statutory rights.

Your statutory rights are not affected.

This warranty does not apply in cases of damage caused by

accident, improper use, abuse and force majeure.

This warranty will be invalidated if the appliance is tampered

with in any way whatsoever.

For warranty claims, please first contact us by telephoning the

service centre free phone number or email:

Dario London Service Centre

PO BOX 1125

Bromley

BR1 9TW

UK: 0800 328 6020

Ireland: 00800 4467 5888

[email protected]

If the appliance has to be returned to us, it must be packed

correctly as we cannot accept any responsibility for damage

caused in transit.

DIGITAL CALIPER GAUGE

Your details:

Name ____________________________________________

Address ___________________________________________

__________________________________________________

___________________E mail _______________________

Date of purchase* __________________________________

* We recommend you keep the receipt with this warranty card

Location of purchase ________________________________

Description of malfunction:

Return your completed warranty card to:

UK + Ireland

Dario London Service Centre

PO BOX 1125

Bromley

BR1 9TW

UK: 0800 328 6020

Ireland: 00800 4467 5888

[email protected] YEAR WARRANTY

IRE

AFTER SALES SUPPORT

[email protected]00800 / 4467 5888

GB 0800 / 328 6020

MODEL: GT-DC-02, 02/13, E45316

Workzone GT-DC-02 User manual

Workzone GT-DC-02 User manual

Workzone GT-DC-02 User manual

Related papers

Other documents