Aero-Stream 102486 Operating instructions

Brand
Aero-Stream
Model
102486
Type
Operating instructions

Aero-Stream 102486 is a device designed to produce an audible signal when the air output drops below 1 PSI. It is commonly used to alert users of potential issues with air compressors or other pneumatic systems.

Capabilities:

  • Produces an audible alarm when air output falls below 1 PSI
  • Easy to install with included airline/tee fitting and adapter assembly
  • Self-contained battery provides power for at least 60 days
  • Battery should be replaced annually, ideally at the same time as home smoke alarms
  • Compact and lightweight design allows for easy mounting on various surfaces

Aero-Stream 102486 is a device designed to produce an audible signal when the air output drops below 1 PSI. It is commonly used to alert users of potential issues with air compressors or other pneumatic systems.

Capabilities:

  • Produces an audible alarm when air output falls below 1 PSI
  • Easy to install with included airline/tee fitting and adapter assembly
  • Self-contained battery provides power for at least 60 days
  • Battery should be replaced annually, ideally at the same time as home smoke alarms
  • Compact and lightweight design allows for easy mounting on various surfaces
PN 102499 Rev B
Figure 1
Figure 2
Figure 3
Figure 4
Aero-ALERT™ Alarm Kit
P/N: 102486
Function:
The Aero-ALERT™ alarm kit is designed to produce an audible signal when the
Aero-Stream® product has an air output of less than 1 PSI. In the event of an
alarm signal see the troubleshooting section below.
Service and Maintenance
The alarm is designed to produce the audible signal for at least 60 days on the self
contained battery. The battery should be replaced annually. It is suggested that
they be replaced at the same time as your fire detection smoke alarm in your
home.
Directions
1. Install the airline/tee fitting in the output air line of the Aero-Stream® unit.
Clamp the air line with plastic clamp (figure 2).
2. If you are using an air line extension kit attached the adapter assembly as
shown in (figure 4)
3. Connect the 1/8” air line from the tee to the pressure switch barbed fitting on
the side of the Aero-ALERT™ (figure 3).
4. Remove the (4) cover screws and the cover. Attach the battery connector
and replace cover and screws. The drain holes must be located on the same
side as the buzzer hole. Hin t: The alarm will sound-off if the compressor is not
running. To temporarily mute the alarm, place a piece of tape over the ¼” buzzer
hole.
5. Clean the enclosure surface with water and then wipe surface with rubbing
alcohol. Remove the protective film from the Velcro pads. With the hose spigot
on the side and buzzer hole facing down, firmly press the alarm to the surface
(figure 4).
Troubleshooting
The alarm will sound-off from the air switch indicating low or no air pressure output.
Follow the steps below to determine the cause of the alarm.
1. Make sure the large air line connections are not leaking. If not leaking go to
step 2 (figure 2).
2. Make sure the small air line is tightly connected to the black “tee” and the
fitting on the pressure switch of the alarm box. If the connections are tight, pinch
the large air line after the black “tee” (on the tank side of the tee) to deadhead
the pump. The sound output of the pump will change. If the alarm goes off the air
switch is o.k. If the alarm does not go out call Aero-Stream®.
Drain
Holes
Down
Buzzer &
Cover Drain
Holes Down
Buzzer hole
down
Pressure
Switch
Adapter
Assembly
  • Page 1 1

Aero-Stream 102486 Operating instructions

Brand
Aero-Stream
Model
102486
Type
Operating instructions

Aero-Stream 102486 is a device designed to produce an audible signal when the air output drops below 1 PSI. It is commonly used to alert users of potential issues with air compressors or other pneumatic systems.

Capabilities:

  • Produces an audible alarm when air output falls below 1 PSI
  • Easy to install with included airline/tee fitting and adapter assembly
  • Self-contained battery provides power for at least 60 days
  • Battery should be replaced annually, ideally at the same time as home smoke alarms
  • Compact and lightweight design allows for easy mounting on various surfaces
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents