urban ambiance UQL2652 Installation guide

Brand
urban ambiance
Model
UQL2652
Type
Installation guide

Urban ambiance UQL2652 is a light fixture that can accommodate three A19 Medium Base bulbs with a maximum wattage of 100W each. It is recommended to use Medium Base Vintage bulbs, which are not included in the package. The fixture is easy to install and can be completed in 20-30 minutes. It comes with all the necessary hardware, including an inner backplate, fixture body, Allen screws, lock screws, and shades. The fixture can be mounted on a wall or ceiling and is perfect for both indoor and outdoor use. It is also dimmable, so you can adjust the brightness to your liking.

Urban ambiance UQL2652 is a light fixture that can accommodate three A19 Medium Base bulbs with a maximum wattage of 100W each. It is recommended to use Medium Base Vintage bulbs, which are not included in the package. The fixture is easy to install and can be completed in 20-30 minutes. It comes with all the necessary hardware, including an inner backplate, fixture body, Allen screws, lock screws, and shades. The fixture can be mounted on a wall or ceiling and is perfect for both indoor and outdoor use. It is also dimmable, so you can adjust the brightness to your liking.

Package Contents
1of2
BAllen Screw
x2
Inner
Backplate
x1
STEP 1 Install Inner Backplate and Fixture Body-
A. Pass the supply wires through Inner Backplate (A). Attach Inner
Backplate (A) to Outlet Box with the head of Green Ground Screw
facing you. Secure it with Outlet Box Screws (not included). Tighten
until snug
B. Refer to Step 2 for wiring connections.
C. Attach Fixture Body (D) over Inner Backplate (A) and secure with
Allen Screws (B). Tighten until snug with screwdrivers.
.
A
Shade
x3
E
Fixture
Body
x1
C
White wire
from supply White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 2
D
Lock Screw
x9
STEP 3 - Install Bulbs and Shade
A. Insert bulbs onto sockets and screw snugly into place.
B. Place Shade (E) into socket cup and hold it by hands. Thread Lock
Screws (C) into mounting holes on socket cup until it is attached to
the neck of Shade (E). Please make sure the Shade (E) is held well
before you release your hands.
Your fixture is now assembled and ready to use. Enjoy!
STEP 2 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires between Inner Backplate (A) and
Fixture Body (D).
Figure 3
Socket Cup
C
Neck
E
A
Figure 1
Outlet Box
Outlet Box Screw
D
B
Supply Wires
and Ground Wire
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Light Source: (3)A19 Medium Base bulbs 100W Maximum or
(3) Medium Base Vintage bulbs are recommended but not supplied.
Estimated Assembly Time: 20-30 minutes
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Vintage Bulb
(recommended
but not supplied)
Installation Instructions: UQL2652
www.urbanambiance.com
2of2
SKU: UQL2652
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4"
25”
8”
6.75” Dia.
8”
5.75”
4.5”
7.75”
www.urbanambiance.com
  • Page 1 1
  • Page 2 2

urban ambiance UQL2652 Installation guide

Brand
urban ambiance
Model
UQL2652
Type
Installation guide

Urban ambiance UQL2652 is a light fixture that can accommodate three A19 Medium Base bulbs with a maximum wattage of 100W each. It is recommended to use Medium Base Vintage bulbs, which are not included in the package. The fixture is easy to install and can be completed in 20-30 minutes. It comes with all the necessary hardware, including an inner backplate, fixture body, Allen screws, lock screws, and shades. The fixture can be mounted on a wall or ceiling and is perfect for both indoor and outdoor use. It is also dimmable, so you can adjust the brightness to your liking.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents