Mammoth R6GP 6, 7.5 - 10 Ton Archived 2/23/12 Product information

Brand: Mammoth

Model: R6GP 6, 7.5 - 10 Ton Archived 2/23/12

Type: Product information

3 Phase 60 Hz.

4. For supply wire ampacities and overcurrent protection, see unit

rating label.

5. On “C” Series Models only. For 208V operation remove wire from

230V tap and place on 208V tap.

6. This wire replaced by auto transformer when used.

1. Couper le courant avant de faire letretien.

2. Employez uniquement des conducteurs en cuivre.

7107530

03/09

WIRING DIAGRAM

R6GP-(072) (C/D) Series

NOTES:

1. Disconnect all power before servicing.

2. For supply connections use copper conductors only.

3. If any of the original wire as supplied with the furnace must be replaced,

it must be replaced with wiring material having a temperature rating of

at least 105C.

CCH - Crankcase Heaters, Stage 1&2 Compressor

CC1&2 - Contactor, Stage 1&2 Compressor

E - Economizer

LVT - Low Voltage Terminal

OFC - Contactor, Outdoor Fan

IBC - Contactor, Indoor Blower Motor

IBC

GND

Compressor 1

CC1

Aux.

Switch

(N.C.)

CC1

CCH1

Field Supplied

Disconnect

(3Phase Power Only)

For supply connections use

copper conductors only.

Unit

Terminal

Block

Transformer

24V Sec.

Primary

Outdoor Fan Motor

Indoor Fan Motor

- Indicates plug connection.

Letter Indicates which plug.

Number indicates pin location.

See Note 5

OFC

4 Amp

Circuit

Breaker

24V Hot

High

Pressure

Switchs

Evap.

Freezestats

Low

Pressure

Switchs

Factory

Jumper

LVT-C (24V COM.)

LVT-R

CC1

LVT-Y1(Stage 1 Cool)

LVT-Y2(Stage 2 Cool)

LVT-G

LVT-W1(Heat)

LVT-W2(Heat)

E-1

E-9

E-8

E-2

E-4

E-5

OFC

CC1

Aux. Switch

(N.O.)

Factory

Jumper

Auto Transformer

460V & 575V

Units Only

WH BK

L3 L2

Inducer Motor

¢710753%¤

See Note 6

208-230/460 Volt

- Indicates screw connection.

Max

Te mp.

Limit

24V Common

Flame

Rollout

Switch

Upper

Scndry

Limit

P1-2

P1-8

P1-3

P2-3

UTEC

IGNITION

CONTROL

COM

BLOWER

TIME

DELAY

P2-4

TRANSFORMER

P2-1

COM

P1-9

P1-6

GAS VALVE

INDUCER MTR

CENTRIFUGAL

SWITCH

SPARK

IGNITOR

FLAME

SENSOR

GND

High

Limit

Input

Rollout Switch

Input

IBC

P1-7

P1-4

24 VAC

P2-2

IC-IND

K4-IC

IC-L1

Status Light

(Red)

Ignition Control Failure Code

Steady On

2 flashes

Operation Normal

3 flashes

4 flashes

5 flashes

6 flashes

7 flashes

8 flashes

9 flashes

10 flashes

Pressure/centrifugal switch open with inducer on

Lockout from too many failed ignition tries

Lockout from too many flame losses

High temperature switch open

Rollout switch open

Flame present with gas off`

Exceeded max limit trips in one call for heat (5)

Gas Valve Fault

Pressure/centrifugal switch closed with inducer off

Mammoth R6GP 6, 7.5 - 10 Ton Archived 2/23/12 Product information

Mammoth R6GP 6, 7.5 - 10 Ton Archived 2/23/12 Product information

Mammoth R6GP 6, 7.5 - 10 Ton Archived 2/23/12 Product information

Related papers

Other documents