Minka Group 7971-17A-66 User manual

Minka Group
Brand
Minka Group
Model
7971-17A-66
Type
User manual

Minka Group 7971-17A-66 is a versatile lighting fixture that can be used in a variety of indoor settings. With its adjustable arms and shades, this fixture can be customized to fit your specific needs. The fixture can be mounted on a wall or ceiling, and it comes with all the necessary hardware for installation.

The 7971-17A-66 is made of high-quality materials, and it is built to last. The fixture is also easy to install and maintain, making it a great choice for any do-it-yourselfer.

Here are some of the features of the Minka Group 7971-17A-66:

  • Adjustable arms and shades for customization

Minka Group 7971-17A-66 is a versatile lighting fixture that can be used in a variety of indoor settings. With its adjustable arms and shades, this fixture can be customized to fit your specific needs. The fixture can be mounted on a wall or ceiling, and it comes with all the necessary hardware for installation.

The 7971-17A-66 is made of high-quality materials, and it is built to last. The fixture is also easy to install and maintain, making it a great choice for any do-it-yourselfer.

Here are some of the features of the Minka Group 7971-17A-66:

  • Adjustable arms and shades for customization
INSTALLATION INSTRUCTIONS
For RLM (Rev. 11/27/2019)
READ AND SAVE THESE INSTRUCTIONS
W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Fig. 1
Fig. 2
Fig. 5
Fig. 3
Fig. 4
MOUNTING THE FIXTURE (Fig.1)
1. Shut off power at the fuse box or circuit breaker box and remove the old fixture
including the mounting hardware.
2. Carefully unpack your new fixture and lay out all the parts in a clear area. Take
care not to misplace any small parts necessary for installation.
3. Position the mounting plate (B) on the wall, and mark location of the two
plastic anchors (A). Drill the holes on the wall, and then insert the plastic
anchors (A).
4. Attach the mounting plate (B) to the junction box using mounting screws (C)
(Size: #8-32N*L0.5"). The side of the mounting plate (B) marked “GND” must
face out.
5. Secure the mounting plate (B) by inserting the wood screws (D) through the
holes on the mounting plate into the plastic anchors (A).
CONNECTING THE WIRES (Fig. 2)
6. Connect the electrical wires as shown in Fig. 2, making sure that all wire
connectors are secured. If your outlet box has a ground wire (green or bare
copper), connect the fixture’s ground wire to it. Otherwise, connect the
fixture’s ground wire directly to the mounting plate (B) using the green screw
provided. After the wires are connected, tuck them carefully inside the junction
box.
FINISHING THE INSTALLATION (Fig.1)
7. Align the fixture body (E) onto the mounting plate (B) followed by plastic
washer (F) and secure with screws (G).
8. Referring to Fig.4 with the product for the shades (I) installation. Place the
shade (I) over socket (H) and secure with socket ring (J).
9. Install (1) one medium base bulb (K) up to 100 watts each or CFL or LED
equivalent (not included) in accordance with the fixture specification—DO
NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER
LA PUISSANCE NOMINALE MAXIMALE!)
10. (For shade#7984-14/18-143C) Install the glass shade (L) into shade (I).
(For shade#7982-9-79) Install the two finials to the two holes of shade.
11. To prevent moisture from entering the outlet box and causing a short, use
clear caulking (i.e. Indoor/Outdoor silicone sealant) to outline the outside of
fixture back plate where it meets the wall leaving a space at the bottom to
allow moisture a means to escape (Fig.5)
Your installation is now complete. Return power and test the fixture.
LA-3130E
FIXTURE
WIRES
Black or
Smooth
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
WIRES
White
(Neutral)
FIXTURE
WIRES
Green or
Bare
Copper
(Ground)
WIRES
Green
(Ground)
Set# A-021-136E
-Mounting Plate
-Ground Screw
-Mounting Screw*2
J
K
L
I
G
A
B
C
D
E
F
H
Socket Ring# SKT-RING-26
7971-12A/17A/24A/29A-66
7972-15C/22C/29C-66
7973-18B/24B/30B-66
7980-8-517/66
7981-9-78/66
7982-9-79/66
7983-9-545/66
7984-14-143C/66
7984-18-143C/66
7985-14-79/66
7985-18-30/66
7986-14-172/30/66
7985-18-172/30/66
Note: The arms (see Fig. 3) and shades (see Fig.4) can be mixed and matched
according to personal preference. Illustration (Fig.1) on this manual is for
installation purposes only.
CAULKING
BACKPLATE
  • Page 1 1

Minka Group 7971-17A-66 User manual

Minka Group
Brand
Minka Group
Model
7971-17A-66
Type
User manual

Minka Group 7971-17A-66 is a versatile lighting fixture that can be used in a variety of indoor settings. With its adjustable arms and shades, this fixture can be customized to fit your specific needs. The fixture can be mounted on a wall or ceiling, and it comes with all the necessary hardware for installation.

The 7971-17A-66 is made of high-quality materials, and it is built to last. The fixture is also easy to install and maintain, making it a great choice for any do-it-yourselfer.

Here are some of the features of the Minka Group 7971-17A-66:

  • Adjustable arms and shades for customization
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents