Minka Group 5763-2560-84 User manual

Brand: Minka Group

Model: 5763-2560-84

Type: User manual

Minka Group 5763-2560-84 is a light fixture that can be mounted on a ceiling. It comes with all the necessary parts for installation, including a circular strap, junction box screws, studs, knurled knobs, and a glass shade. The fixture has a maximum wattage rating, so be sure not to exceed it when installing light bulbs. The installation process is relatively simple and can be completed in a few steps. First, shut off the power at the circuit breaker and remove the old fixture. Then, attach the circular strap to the junction box with the provided screws.

Minka Group 5763-2560-84 is a light fixture that can be mounted on a ceiling. It comes with all the necessary parts for installation, including a circular strap, junction box screws, studs, knurled knobs, and a glass shade. The fixture has a maximum wattage rating, so be sure not to exceed it when installing light bulbs. The installation process is relatively simple and can be completed in a few steps. First, shut off the power at the circuit breaker and remove the old fixture. Then, attach the circular strap to the junction box with the provided screws.

INSTALLATION INSTRUCTIONS

Item#5763 (Rev. 02/27/2012)

READ AND SAVE THESE INSTRUCTIONS

WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.

AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

Fig. 1

Fig. 2

MOUNTING THE FIXTURE (Fig. 1)

1. Shut off power at the circuit breaker and remove old

fixture, including the mounting hardware.

2. Carefully unpack your new fixture and lay out all the

parts on a clear area. Take care not to lose any small

parts necessary for installation.

3. Attach the Circular Strap (A) to the Junction Box with

the two Junction box Screws (B) (Size:

#8-32N*L0.5”) as shown. The side of the Circular

Strap marked “GND” must face out.

4. Thread the Studs (D) into the pre-drilled holes of the

Circular Strap (A) space the same distance apart as

the hole in the fixture canopy.

CONNECTING THE WIRES (Fig. 2)

5. Connect the fixture wires to the junction box wires as

shown in Fig. 2. Making sure all wire connectors are

secured and do not easily pull off with a slight tug. If

there is no Green Ground wire from the junction box,

connect the Fixture Ground Wire to the Circular Strap

with the green Screw provided.

COMPLETING THE INSTALLATION (Fig. 1)

6. Place Fixture Body (C) onto Studs (D) and secure

with Knurled Knobs (E).

7. Place the Glass Shade (F) over the socket, fasten

with Screw Shell (G).

8. Install the light bulbs (not included) in accordance

with the fixture’s specifications. (DO NOT EXCEED

THE MAXIMUM WATTAGE RATING!) (NE PAS

DEPASSER LA PUISSANCE NOMINALE

MAXIMALE!)

Your installation is now complete. Return power to

the outlet box and test the fixture.

Note: Illustration (Fig. 1) on this manual is for

installation purposes only. It may or may not be

identical to the fixture purchased.

LA-1810E

FIXTURE

WIRES

Black or

Smooth

HOUSE

WIRES

Black

(Hot)

FIXTURE

WIRES

White or

Ribbed

HOUSE

WIRES

White

(Neutral)

FIXTURE

WIRES

Bare

Copper

(Ground)

HOUSE

WIRES

Green

(Ground)

A

B

G

F

C

D

E

Set# A-020

- Circular strap

- Ground screw

- Mounting Screw*2

Socket ring # SKT-RING-26

1

Minka Group 5763-2560-84 User manual

Brand: Minka Group

Model: 5763-2560-84

Type: User manual

Minka Group 5763-2560-84 is a light fixture that can be mounted on a ceiling. It comes with all the necessary parts for installation, including a circular strap, junction box screws, studs, knurled knobs, and a glass shade. The fixture has a maximum wattage rating, so be sure not to exceed it when installing light bulbs. The installation process is relatively simple and can be completed in a few steps. First, shut off the power at the circuit breaker and remove the old fixture. Then, attach the circular strap to the junction box with the provided screws.

Download PDF

Related papers

Other documents