Kelvinator JT4BE048KA Operating instructions

Brand: Kelvinator

Model: JT4BE048KA

Category: Split-system air conditioners

Type: Operating instructions

AIR HANDLER

B6BM, B6EM, & B6VM SERIES

INSTALLATION INSTRUCTIONS

IMPORTANT

ATTENTION INSTALLERS:

It is your responsibility to know this product better than your customer. This includes being

able to install the product according to strict safety guidelines and instructing the customer on

how to operate and maintain the equipment for the life of the product. Safety should always be

the deciding factor when installing this product and using common sense plays an important

role as well. Pay attention to all safety warnings and any other special notes highlighted in the

manual. Improper installation of the furnace or failure to follow safety warnings could result in

serious injury, death, or property damage.

These instructions are primarily intended to assist qualiﬁed individuals experienced in the proper

installation of this appliance. Some local codes require licensed installation/service personnel

for this type of equipment. Please read all instructions carefully before starting the installation.

Return these instructions to the customer’s package for future reference.

DO NOT DESTROY. PLEASE READ CAREFULLY & KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

TABLE OF CONTENTS

IMPORTANT SAFETY INFORMATION .....................3

REQUIREMENTS & CODES .....................................3

GENERAL INFORMATION ........................................4

Before You Install this Unit ....................................... 4

Locating the Air Handler .......................................... 4

Minimum Clearances ............................................... 4

Operation of Air Handler During Construction .........4

Installation in a Garage ...........................................5

Plenums & Air Ducts ...............................................5

Unconditioned Spaces .........................................5

Air Filters ..............................................................5

Acoustical Duct Work ...........................................5

AIR HANDLER INSTALLATION ................................6

Packaging Removal ................................................. 6

Mounting Applications .............................................6

Upﬂow Installations .................................................6

Downﬂow Installations ............................................. 6

Horizontal Installations ............................................7

Horizontal Left Installations: .................................7

Horizontal Right Installations: ............................... 7

Refrigerant Line Connections .................................. 8

Oriﬁce Removal & Installation ..............................8

Connecting the Linesets ......................................9

Condensate Drainage .............................................10

ELECTRICAL CONNECTIONS .................................11

Pre-Electrical Checklist:...........................................11

Line Voltage ............................................................. 11

Grounding................................................................11

Thermostat Connections .........................................11

Control Board ..........................................................12

Twinning ...............................................................12

Heater Kits...............................................................12

Electronic Air Cleaner (EAC) ................................... 13

Humidiﬁer ................................................................13

Optional Humidistat .................................................13

STARTUP & ADJUSTMENTS ...................................13

Before You Start the Unit .........................................13

Refrigerant Charging ...............................................14

Air Circulation ..........................................................14

Running the Blower Continuously ........................14

Selecting continuous low speed fan operation .....14

Turning the Blower Off..........................................14

System Cooling ....................................................14

System Heating .................................................... 14

Selecting Minimum Electric Heat Airﬂow ..............14

Blower Conﬁgurations .............................................14

Determining Nominal System Capacity ...............14

3-Speed Units ......................................................14

High Efﬁciency Units (Variable & Fixed Speed) ...15

Selecting Basic Heating Airﬂow ...........................15

Selecting Basic Cooling / Heat Pump Airﬂow .......15

Dehumidiﬁcation Options ........................................15

UNIT MAINTENANCE ................................................16

TROUBLESHOOTING ...............................................16

FIGURES & TABLES .................................................17

Figure 11. B6 Series Physical Dimensions ..........17

Figure 12. Air Handler Components ..................... 18

Table 5. B6BM Airﬂow Data .................................. 19

Airﬂow Data .............................................................19

Table 6. B6EM (FSHE) Airﬂow Data ..................... 20

Table 7. B6EM (FSHE) Minimum Heating Airﬂow

Settings (CFM) .....................................................21

Table 8. B6VM Recommended Cooling Airﬂow

Settings ................................................................21

Table 9. B6VM (VSHE) Airﬂow Data ....................22

Electrical Diagrams & Data .....................................23

Figure 13. Single Stage Control Board ................23

Figure 14. Two - Stage Control Board ..................23

Figure 15. Fixed Speed Motor Control Board ....... 24

Figure 16. Variable Speed Motor Control Board ...24

Figure 17. B6BM Wiring Diagram .........................25

Figure 18. B6EM Wiring Diagram .........................26

Figure 19. B6VM Wiring Diagram .........................27

Table 10. B6BM MCA & MOP Data ...................... 28

Table 11. B6(E,V)M MCA & MOP Data ................29

Table 12. Control Board Operation .......................29

INSTALLATION / PERFORMANCE CHECK LIST ....32

IMPORTANT SAFETY INFORMATION

Please read all instructions before servicing this equipment.

Pay attention to all safety warnings and any other special

notes highlighted in the manual. Safety markings are used

frequently throughout this manual to designate a degree

or level of seriousness and should not be ignored.

WARNING indicates a potentially hazardous situation that

if not avoided, could result in personal injury or death.

CAUTION indicates a potentially hazardous situation that

if not avoided, may result in minor or moderate injury or

property damage.

WARNING:

ELECTRICAL SHOCK, FIRE OR

EXPLOSION HAZARD

Failure to follow safety warnings exactly could

result in serious injury or property damage.

Improper servicing could result in dangerous

operation, serious injury, death or property

damage.

• Beforeservicing,disconnectallelectricalpower

to the indoor blower.

•Whenservicingcontrols,labelallwiresprior

to disconnecting. Reconnect wires correctly.

• Verifyproperoperationafterservicing.

WARNING:

B6 series air handlers leave the factory with

a nitrogen holding charge. Use caution when

preparing coils for ﬁeld connections. If repairs

make it necessary for evacuation and charging,

it should only be attempted by qualified,

trained personnel thoroughly familiar with this

equipment. Some local codes require licensed

installation service personnel to service this type

of equipment. Under no circumstances should

the equipment owner attempt to install and/or

service this equipment. Failure to comply with

this warning could result in equipment damage,

personal injury, or death.

NITROGEN

HEALTH

FLAMMABILITY

REACTIVITY

0 Minimal Hazard

1 Slight Hazard

REQUIREMENTS & CODES

WARNING:

This unit must be installed in accordance

with instructions outlined in this manual

during the installation, service, and operation

of this unit. Unqualiﬁed individuals should

not attempt to interpret these instructions or

install this equipment. Failure to follow safety

recommendations could result in possible

damage to the equipment, serious personal

injury or death.

• The installer must comply with all local codes and

regulations which govern the installation of this type

of equipment. Local codes and regulations take

precedence over any recommendations contained in

these instructions. Consult local building codes for

special installation requirements.

• Thisequipmentcontainsnitrogengas.Installationor

servicing should only be performed by qualiﬁed trained

personnel thoroughly familiar with this type equipment.

• Allelectricalwiringmustbecompletedinaccordance

with local, state and national codes and regulations

and with the National Electric Code (ANSI/NFPA 70)

or in Canada the Canadian Electric Code Part 1 CSA

C.22.1.

• Installationofequipmentmayrequirebrazingoperations.

Installer must comply with safety codes and wear

appropriate safety equipment (safety glasses, work

gloves, ﬁre extinguisher, etc.) when performing brazing

operations.

• Installthisunitonlyinalocationandpositionasspecied

on page 4 & page 5. This unit is designed only

for Indoor installations and should be located with

consideration of minimizing the length of the supply and

return ducts. See Table 5, (page 19), Table 6, (page

20), Table 7, (page 21), Table 8, (page 21), &

Table 9, (page 22) and the rating plate for proper

circulating airﬂow data.

• Follow all precautions in the literature, on tags, and

on labels provided with the equipment. Read and

thoroughly understand the instructions provided with

the equipment prior to performing the installation and

operational checkout of the equipment.

• This airhandler maybe used for temporary heating

of buildings or structures under construction. See the

guidelines listed on page 4.

• Airhandlerinstallationsinaresidentialgaragemustbe

installed as speciﬁed on page 5.

GENERAL INFORMATION

This appliance has been tested for capacity and efﬁciency

in accordance with AHRI Standards and will provide

many years of safe and dependable comfort, providing

it is properly installed and maintained. Abuse, improper

use, and/or improper maintenance can shorten the life

of the appliance and create unsafe hazards. Please read

all instructions before installing the unit.

Before You Install this Unit

√ This equipment is securely packaged at the time of

shipment and upon arrival should be carefully inspected

for damage prior to installing the equipment at the job

site. Claims for damage (apparent or concealed) should

be ﬁled immediately with the carrier.

√ it is recommended that the cooling load of the area to

be conditioned should be calculated and a system of

the proper capacity selected.

√ Check the electrical supply and verify the power supply

is adequate for unit operation. The system must be wired

and provided with circuit protection in accordance with

local building codes. If there is any question concerning

the power supply, contact the local power company.

√ Verify the duct system is appropriate for the air handler

being installed. Please note that when replacing an

existing system with lower air-ﬂow, the duct system

may require modiﬁcation.

Locating the Air Handler

• Surveythejobsitetodeterminethebestlocationfor

mounting the unit. Consideration should be given to

availability of electric power, service access, and noise.

• Thedimensions of theroomor alcovemustbeable

to accommodate the overall size of the unit and the

installation clearances listed in Table 1. Physical

dimensions for this air handler are also shown in Figure

11 (page 17).

• Theairhandlershouldbesetintopositionbeforerouting

the refrigerant tubing.

Minimum Clearances

• This appliancemust beinstalled in accordance with

clearances listed in Table 1. The air handler must be

installed with ample clearance for easy access to the

air ﬁlter, blower assembly, heater assembly, controls,

and vent connections. Applicable building codes may

require additional clearance to equipment. Refer to

applicable building codes for details.

• Staticpressure drop throughlouveredopeningsand

through return air plenums should be considered in

the overall duct design in the determination of the total

external static pressure.

Table 1. Minimum Unit Clearances

INSTALLATION CLEARANCES

Left Side ............. 0 Inches

Right Side ......... 0 Inches

Back .................. 0 Inches

Front ...............†See Notes

†

NOTE:

Alcove Installations - Allow 24 in. minimum clearance from front

of unit to nearest wall or partition for servicing. Recommended

clearance is 36 in.

REAR

RIGHT

SIDE

LEFT

SIDE

FRONT

Operation of Air Handler During Construction

CAUTION:

Failure to follow these instructions will void the

factory warranty and may signiﬁcantly reduce

the life or the performance of the air handler,

and/or result in other unsafe conditions. It is

the responsibility of the installing contractor to

insure these provisions are met.

Operating an air handler in a construction environment

can cause the appliance a variety of problems. Proper

use of commercial portable space heating equipment

during construction is recommended. This air handler

may be used during construction if it is not in violation of

any applicable codes and the following criteria are met:

• The installation must meet all applicable codes and

be permanently installed according to the instructions

supplied with the air handler including electrical supply

and duct work.

• Theairhandlermustbecontrolledbyaproperlyinstalled

thermostat that complies with the current provisions

of the NEC (ANSI/NFPA 70) and all applicable codes

having jurisdiction. Thermostat connections must be

made in accordance with instructions supplied with

the air handler and thermostat. See page 11 & page

12.

• Theinstallationmustincludeaproperlyinstalledlterin

the return air system with no by-pass air. The ﬁlter must

be inspected frequently and replaced when necessary.

• Returnairmustbesuppliedunrestrictedandlocated

such that dust and gases from construction activity are

not introduced into the circulating air system.

• Before occupying the structure: The lter must be

replaced or cleaned, the duct work must be inspected

and cleaned of any construction debris, and the air

handler must be cleaned and/or repaired if found to

be dirty, damaged, or malfunctioning in any way by

a qualiﬁed HVAC technician. The air handler shall be

inspected and approved by applicable local authority

even if this requires redundant inspections.

• The serial number for the air handler used during

construction must be submitted in writing (fax and

email also acceptable). This information will be used to

track the long-term affects of air handler usage during

construction. Proof of this submittal shall be available for

the ﬁnal inspection of the air handler prior to occupancy.

Installation in a Garage

WARNING:

Do not place combustible materials on or against

the cabinet. Do not place ﬂammable materials,

(gasoline, paint thinners, etc.) or any other

ﬂammable vapors and liquids, in the vicinity of

the air handler.

The B6 Series air handler may be installed in a residential

garage with the provision that the unit must be located or

protected to prevent physical damage by vehicles.

Plenums & Air Ducts

• Plenums and air ducts should be installed in

accordance with the standards of the National Fire

Protection Association Standard for Installation of

Air Conditioning Systems (NFPA 90A), Standard for

Installation of Residence Type Warm Air Heating

and Air Conditioning Systems (NFPA 90B), and all

applicable local codes. NFPA publications are available

by writing to: National Fire Protection Association,

Batterymarch Park, Quincy, ME 02269 or visit

www.NFPA.org online.

WARNING:

All return ducts must be secured to the air handler

using appropriate methods. All return ducts must

be adequately sealed. When return air is provided

through the bottom of the unit, the joint between

the air handler and the return air plenum must

be air tight.

Return air and circulating air ducts must not be

connected to any other heat producing device

such as a ﬁreplace insert, stove, etc. This may

result in fire, explosion, carbon monoxide

poisoning, personal injury, or property damage.

• Designtheductworkaccordingtomethodsdescribed

by the Air Conditioning Contractors of America (ACCA).

• Thisunitisdesignedonlyforusewithareturnandsupply

duct. The return air duct must have the same free area

as the opening provided on the air handler. The ducts

should be appropriately sized to the capacity of the air

handler to ensure its proper airﬂow rating.

• Use transition ttings if the supply and/or return air

openings of the unit do not match the duct openings.

These transitions should be dimensioned in accordance

with standard practice as speciﬁed in the ASHRAE

recommendations for duct transitions.

• Flexible connectors may be used between the unit

and the ductwork to prevent transmission of vibration

from the unit to the structure. If electric heater kits are

installed, heat resistant material must be used for the

ﬂexible connector at the supply air end of the unit.

• It is good practiceto seal all connections and joints

with industrial grade sealing tape or liquid sealant.

Requirements for sealing ducts vary from region to

region. Consult with local codes for requirements speciﬁc

to your area.

Unconditioned Spaces

All duct work passing through unconditioned space must

be properly insulated to minimize duct losses and prevent

condensation. Use insulation with an outer vapor barrier.

Refer to local codes for insulation material requirements.

Air Filters

B6 Series Air Handlers are not supplied with an air ﬁlter

when shipped from the factory. The installer must provide

a high velocity ﬁlter that is appropriately sized to the return

air duct opening or ﬁlter rack located in the bottom of the

unit. Accessing the ﬁlter does not require tools and can

be removed from the front of the unit by removing the ﬁlter

door. See Unit Maintenance (page 16) for ﬁlter sizes

and installation information.

WARNING:

Never operate the air handler without a ﬁlter

or with doors removed. Dust and lint can build

up on internal components, resulting in loss of

efﬁciency, equipment damage, and possible ﬁre.

Acoustical Duct Work

• Certaininstallationsmayrequiretheuseofacoustical

lining inside the supply duct work. Acoustical insulation

must be in accordance with the current revision of the

Sheet Metal and Air Conditioning Contractors National

Association (SMACNA) application standard for duct

liners. Duct lining must be UL classiﬁed batts or blankets

with a ﬁre hazard classiﬁcation of FHC-25/50 or less.

• Fiberductworkmaybeusedinplaceofinternalduct

liners if the ﬁber duct work is in accordance with the

current revision of the SMACNA construction standard

on ﬁbrous glass ducts. Fibrous duct work and internal

acoustical lining must be NFPA Class 1 air ducts when

tested per UL Standard 181 for Class 1 ducts.

• Dampingducts,exiblevibrationisolators,orpleated

media-style ﬁlters on the return air inlet of the air

handler may be used to reduce the transmission of

equipment noise eminating from the air handler. These

treatments can produce a quieter installation, particularly

in the heated space. However, they can increase the

AIR HANDLER INSTALLATION

The B6 Series Air Handler is shipped ready for vertical

upﬂow installation and is approved for attic, basement,

alcove/closet or crawlspace installation with zero clearance

to combustibles. See Table 1, (page 4) for required

installation clearances. This appliance is approved only

for indoor use.

• Theunitmustbeleveledatinstallationandattachedto

a properly installed duct system.

• Thesurfacethattheairhandlerismountedonmust

provide sound physical support of the unit.

• Theairhandlermustbeinstalledsothatallelectrical

components are protected from water.

• Ifalouvereddoorisinstalledacrossthefrontofthis

unit, the appliance must be mounted ﬂush or behind

front edge of ﬁnished wall.

• Always reinstall the doors on the air handler after

servicing or cleaning/changing the ﬁlters. Do not operate

the air handler without all doors and covers in place.

Packaging Removal

Remove the shipping crate and User’s Manual from the

equipment. When removing the crate, use extra care so

tubing connections are not damaged. Do not pull on the

coils upper tubes.

Mounting Applications

Vertical only air handlers are factory ready for upﬂow

applications. These units may be applied in downﬂow

applications when applied with the appropriate ﬁeld kit.

Factory ready horizontal air handlers may be applied in

upﬂow or horizontal-left and -right discharge applications.

These units may also be applied in downﬂow discharge

when applied with the appropriate ﬁeld kit as speciﬁed in

the units Technical Speciﬁcations.

Through-the-floor installations require a 1/4” thick

noncombustible resilient gasket to be used whenever the

supply or return air ducts pass through the ﬂoor. The gasket

should be positioned between the duct, unit, and ﬂoor.

Upﬂow Installations

All air handlers are factory shipped, ready for upﬂow

installation. The horizontal drain pan may be removed

from the air handler when installing the unit in an upﬂow

conﬁguration. All return air must enter from the bottom of

the unit. A typical upﬂow unit is shown in Figure 1.

Downﬂow Installations

The downﬂow accessory kit (See Technical Speciﬁcations)

is required for downﬂow applications. Instructions for

installing the downﬂow accessory kit are included with the

kit. It is recommended that the accessory be installed prior

to installing the unit. All return air in downﬂow applications

must enter through the top of the unit. A typical installation

of the unit in a downﬂow application is shown in Figure 2.

Horizontal

Drain Pan

Return

Air

Figure 1. Upﬂow Installation

Figure 2. Downﬂow Installation

Tube

Close-off

Plate

Coil

Cabinet

Adaptor Kit

pressure drop in the duct system. Care must be taken

to maintain the proper maximum pressure rise across

the air handler, temperature rise and ﬂow rate. This

may mean increasing the duct size and/or reducing the

blower speed. These treatments must be constructed

and installed in accordance with NFPA and SMACNA

construction standards. Consult with local codes for

special requirements. For best sound performance, be

sure to install all the needed gaskets and grommets

around penetrations into the air handler, such as for

electrical wiring.

Horizontal Installations

The B6 Series air handler can be installed horizontally in

an attic, basement, crawl space or alcove. It can also be

suspended from a ceiling in a basement or utility room in

either a right to left airﬂow or left to right airﬂow as shown

in Figure 3. Air handlers may or may not be shipped from

the factory with all the parts required for horizontal left

applications and horizontal right applications. If your unit

does not have parts for a horizontal application, a kit may

be available.

NOTE: In all horizontal applications in which the unit is

installed above a ﬁnished ceiling and/or living space, a

secondary drain pan must be installed under the entire unit

to avoid damage to the ceiling in the event of condensate

overﬂow. Additionally, it is recommended that an approved

water level indicator or ﬂoat switch device be used to

shut down the unit in the event water is detected in the

auxiliary drain pan.

If suspending the air handler from the ceiling, assemble

a support frame (Figure 4) using slotted iron channel and

full threaded rod. Fasten the frame together with nuts,

washers, and lockwashers. Secure the support frame

to the rafters with lag bolts. The air handler can also be

suspended using steel straps around each end of the

unit. The straps should be attached to the air handler with

sheet metal screws and to the rafters with bolts.

Horizontal Left Installations:

1. Remove the coil access door.

2. Remove the plug from one of the threaded holes in the

horizontal drain pan. Completely remove the webbing

located in the threaded holes of the horizontal drain

pan. IMPORTANT: If the webbing is not removed,

the condensate will not drain properly and ceiling

damage may occur.

3. Insert the plug (from horizontal drain pan) into the open

and unused drain hole in the drain pan at the bottom

of the unit to block bypass air.

4. Remove the corresponding drain line knockout from

the coil access door to allow access to the horizontal

drain.

5. Replace the door and attach the drain line.

Horizontal Right Installations:

1. Remove the coil access door. Unscrew the line-set tube

close-off plate from the front left cabinet rail.

2. Slide the coil and drain pan assembly out of the unit.

3. Remove the sheet metal hairpin covers (if supplied)

from the back of the coil and discard.

4. Place the horizontal drain pan on the opposite side of

the coil. On units with 2 sets of knockouts, remove the

other set of knockouts in the coil spacing plates and

insert support rod.

5. Slide the coil and the horizontal drain pan assembly

back into the unit. Re-attach the tube close off plate.

NOTE: For A-size cabinet applications, it may be

preferrable to remove the blower assembly prior

to installing the coil & drainpan. In this case follow

instructions 1-4 as listed above but also remove the

blower access door and blower assembly. The blower

assembly is secured with two screws on either side

near the front. With these removed the blower assembly

can slide out of the front of the unit. Install the coil and

drain pan as described in step 5 and then replace the

blower assembly. Take care to ensure that the ﬂanges

on the sides of the blower assembly are captured by

the pockets in the blower deck. It may be necessary to

lift the blower assembly during insertion to allow the

lower blower leg to clear the side of the drain pan. The

blower will stop against the back of the blower deck.

Replace the two screws and the blower access door

and procede with steps 6-9.

6. Remove the plug from one of the threaded holes

in the horizontal drain pan. Completely remove the

webbing located in the threaded holes of the drain

pan. IMPORTANT: If the webbing is not removed,

the condensate will not drain properly and ceiling

damage may occur.

NOTE: It is recommended that the suction line be

insulated up to the coil inside of the cabinet.

Threaded

Rod

Lag

Bolt

Nuts (x2)

Washer

and

Lockwasher

Nuts (x2)

Figure 4. Unit Horizontally Suspended

Figure 3. Horizontal Conﬁgurations

HORIZONTAL RIGHT

HORIZONTAL LEFT

RETURN

AIR

RETURN

AIR

WARNING:

The coil in the air handler is factory shipped with

a nitrogen charge. Avoid direct face exposure

or contact with valve when gas is escaping.

Always ensure adequate ventilation is present

during the depressurization process. Address

any uncertainties before proceeding. Failure

to comply with this warning could result in

equipment damage, personal injury, or death.

Refrigerant Line Connections

• Theinstaller shouldmakeeveryeffortto ensurethe

ﬁeld installed refrigerant containing components of the

system have been installed in accordance with these

instructions and sound installation practices for reliable

system operation and longevity.

• Theairhandlercoildoesnotcontainarefrigerantcharge.

Refer to the installation instructions supplied with the

outdoor unit for refrigerant charge information.

• Alwaysrefertotheinstallationinstructionssuppliedwith

the outdoor unit for piping requirements. The suction

and liquid lines must be sized in accordance with the

condensing unit speciﬁcations. See Figure 8 (page 10)

for liquid and suction line locations.

• When connecting refrigerant linesets together, it is

recommended that dry nitrogen be ﬂowing through the

joints during brazing. This will prevent internal oxidation

and scaling from occurring.

• Refrigeranttubingshouldberoutedinamannerthat

minimizes the length of tubing and the number of bends

in the tubing. It should be supported in a manner that

prevents it from vibrating or abrading during system

operation. Tubing should be kept clean of foreign debris

during installation.

• Ifpreciseformingofrefrigerantlinesisrequired,acopper

tubing bender is recommended. Avoid sharp bends and

contact of the refrigerant lines with metal surfaces.

NITROGEN

HEALTH

FLAMMABILITY

REACTIVITY

0 Minimal Hazard

1 Slight Hazard

Figure 5. Loosening of Nut & Distributor Body

7. Insert the plug (from horizontal drain pan) into the open

and unused drain hole in the drain pan at the bottom

of the unit to block bypass air.

8. Remove the corresponding drain line knockout from

the coil access door to allow access to the horizontal

drain.

9. Replace the door and attach the drain line

• Refrigerant lines should be wrapped with pressure

sensitive neoprene or other suitable material where

they pass against sharp sheet metal edges.

• B6 Series air handlers are charged through service

valves on the end of the liquid tube for each circuit.

These must be removed before brazing the line sets.

Oriﬁce Removal & Installation

The oriﬁce installed in the air handler has been sized for

use with the most popularly matched outdoor units. The

oriﬁce size as shipped from the factory is listed on the air

handler rating plate. Perform steps 1 - 9 to conﬁrm that

the oriﬁce size meets the requirements outlined in the

outdoor unit installation manual.

1. Remove the cap from the end of the liquid line.

2. Verify pressurization by depressing the Schrader valve

on the end of the liquid line. Listen for any escaping gas.

If there is no pressure, test the coil for leakage.

• Ifleakageisfound,clearlymarkthelocationoftheleak

and return the coil to the distributor for processing.

• Ifnoleaksarefound,thecoilmaybeinstalled.

3. Depress the valve to relieve all pressure from the coil.

4. Remove and discard the valve core.

CAUTION:

To prevent damage to the unit or internal

components, it is recommended that two

wrenches be used when loosening or tightening

nuts. Do not over tighten!

5. Using two wrenches, loosen the nut and distributor body

as shown in Figure 5. Turn the assembly nut counter-

clock-wise until the oriﬁce body halves are seperated.

6. Insert a light-gauge wire hook between the distributor

body and the restrictor oriﬁce while being careful not

to scratch either part. Carefully remove the restrictor

oriﬁce from the distributor body. See Figure 6 (page

9).

Connecting the Linesets

IMPORTANT NOTES FOR HORIZONTAL OR

DOWNFLOW INSTALLATIONS WITH TXV VALVE:

• Thesensingbulbmustbelocatedushagainstthe

suction line for optimum heat transfer.

• Avoidattachingthesensingbulbtothelowestpartof

the suction line where condensate may accumulate.

• Donotlocatethesensingbulbonverticalsections

of the lineset.

• Forhorizontallines,thebulbshouldnotbelocated

at 12 or 6 o’clock position of the suction line. The

best location is at 4 or 8 o’clock.

• Foradditionalinformationonpropersensingbulb

locations, please refer to the valve manufacturer’s

instructions.

IMPORTANT: The steps in the Orifice Removal &

Installation section (page 8) must be performed before

the linesets are connected.

1. Remove grommets from line set holes.

CAUTION:

It is recommended that a wet rag be wrapped

around the suction line in front of the close off

plate or the sensing bulb (if TXV is installed)

before applying heat. Failure to keep components

cool during brazing may result in structural

damage, premature equipment failure, or possible

personal injury.

2. Unbraze and remove the cap on the suction line.

3. Route and cut both lineset tubes to proper length in

accordance with the outdoor unit speciﬁcations. Verify

the ends are round, clean, and free of any burrs.

4. Position grommet on line set with sufﬁcient distance away

from brazing area. Brazing processes can permanently

damage grommets.

5. Connect the suction and liquid lineset tubes.

CAUTION:

It is recommended that a wet rag be wrapped

around the suction line in front of the close off

plate or the sensing bulb (if TXV is installed)

before applying heat. Failure to keep components

cool during brazing may result in structural

damage, premature equipment failure, or possible

personal injury.

6. Braze the individual connections with dry nitrogen

ﬂowing through the joints. NOTE: This will prevent

internal oxidation and scaling from occurring.

7. Wrap the refrigerant lines with pressure sensitive

neoprene or other suitable material especially where

the lines enter the opening in the sheet metal.

Figure 6. Restrictor Insertion into Distributor Body

Figure 7. Removal of Oriﬁce

7. Check the actual size of the new oriﬁce. NOTE: The

size is stamped on its side. Do not use pin gauges to

measure the oriﬁce diameter.

8. Insert the new oriﬁce into the distributor body, rounded

end down. See Figure 7.

CAUTION:

To prevent damage to the unit or internal

components, it is recommended that two

wrenches be used when loosening or tightening

nuts. Do not over tighten!

9. Realign the assembly nut on the distributor body and

hand tighten both components. Mark a line on both

bodies and then tighten an additional 1/4 turn using two

wrenches. The movement of the two lines will show how

much the nut is tightened. If a torque wrench is used,

tighten to 10-12 ft. lbs. or 14-16 Nm.

• Iftheairhandlerislocatedinorabovealivingspace

where damage may result from condensate overﬂow,

an auxiliary drain pan shall be installed under the unit.

A separate drain line should extend from the pan to a

conspicuous point and serve as an alarm indicating

that the primary drain is restricted. As an alternative to

a separate drain line, an approved water level indicator

or ﬂoat switch device may be used to shut down the

unit in the event water is detected in the auxiliary pan.

• Installasingle5inchtrapinthecondensatedrainline

as close to the coil as possible. Make sure that the

top of the trap is below the bottom of the drain pan to

prevent the condensate from overﬂowing the drain pan.

NOTE: There must be only one trap in the drain line.

Using more than one trap may prevent drainage.

• Primethetrapwithwater.Insulatethedrainifitislocated

in an unconditioned space, and test the condensate line

for leaks. Consult local codes for additional restrictions

or precautions.

• During system checkout, inspect the drain line and

connections to verify proper condensate drainage.

8. Evacuate the system of moisture and non-condensables

to prevent low efﬁciency operation or damage to the

unit. The suggested range of evacuation is 350 - 500

microns.

9. Charge the system with refrigerant. Refer to the

outdoor unit installation manual for additional charging

instructions.

10. Check the system for leaks, including the lineset and

the brazed joints.

11. Replace all grommets and properly dispose of all

removed parts.

Condensate Drainage

CAUTION:

The air handler must be level to ensure proper

condensate drainage. An unlevel installation may

result in structural damage, premature equipment

failure, or possible personal injury.

• Methodsfordisposingofcondensatevaryaccording

to local codes. Refer to local codes or authority having

jurisidiction for restrictions and proper condensate

disposal requirements.

• The drain pan that is supplied with this air handler

contains a primary and secondary drain ﬁtting. The

condensate is drained from the unit through two 3/4”

female pipe ﬁttings located on the front side of the unit

as shown in Figure 8.

• Thedrainpanmustbedrainedwitheldsuppliedtubing

or pvc pipe and adequately trapped. Both drain tubes

must have a minimum diameter of 3/4” and be trapped

separately.

IMPORTANT: Failure to install a trap may result in

condensation overﬂowing the drain pan, resulting in

substantial water damage to surrounding area.

• Routebothlinestoasuitabledrain,avoidingsharpbends

and pinching of the lines. The drain should maintain a

minimum horizontal slope in the direction of discharge

of not less than 1” vertical for every 10 ft of horizontal

run.

3/4” Adapter w/

3/4” dia. hose barb

3/4” minimum dia.

PVC or flexible tubing

HORIZONTAL

UPFLOW

DOWNFLOW

NOTES:

1. The drain lines must maintain a downward slope to ensure proper

condensate drainage.

2. Each condensate drain must be trapped separately using a J-Trap or

field supplied loop.

Figure 8. Condensate Drainage Example

ELECTRICAL CONNECTIONS

WARNING:

ELECTRICAL SHOCK, FIRE OR

EXPLOSION HAZARD

Failure to follow safety warnings exactly could

result in serious injury or property damage.

Improper servicing could result in dangerous

operation, serious injury, death or property

damage.

• Beforeservicing,disconnectallelectricalpower

to the indoor blower.

• Whenservicingcontrols,labelallwiresprior

to disconnecting. Reconnect wires correctly.

• Verifyproperoperationafterservicing.

• Electrical connections must be in compliance with

all applicable local codes and ordinances, and with

the current revision of the National Electric Code

(ANSI/NFPA 70).

• ForCanadianinstallations,theelectricalconnections

and grounding shall comply with the current Canadian

Electrical Code (CSA C22.1 and/or local codes).

Pre-Electrical Checklist:

√ Verify the voltage, frequency, and phase of the supply

source match the speciﬁcations on the unit rating plate.

√ Verify that the service provided by the utility is sufﬁcient

to handle the additional load imposed by this equipment.

See the unit wiring label or Table 10, (page 28) &

Table 11, (page 29) for proper high and low voltage

wiring.

√ Verify factory wiring is in accordance with the unit wiring

diagram (Figure 17 (page 25), Figure 18 (page 26),

& Figure 19 (page 27)). Make sure the connections

didn’t loosen during shipping or installation.

Line Voltage

• An electrical disconnect must be located within sight

of and readily accessible to the unit. This switch shall

be capable of electrically de-energizing the outdoor unit.

See unit data label for proper incoming ﬁeld wiring. Any

other wiring methods must be acceptable to authority

having jurisdiction.

• Itisrecommendedthatthelinevoltagetotheunitbe

supplied from a dedicated branch circuit containing the

correct fuse or circuit breaker for the unit.

• Overcurrentprotectionmustbeprovidedatthebranch

circuit distribution panel and sized as shown on the unit

rating label and according to applicable local codes.

See the unit rating plate and Table 10, (page 28) &

Table 11, (page 29) for maximum circuit ampacity

and maximum overcurrent protection limits.

• The installer should become familiar with the wiring

diagram/schematic before making any electrical

connections to the unit. See the unit wiring label or

Figure 17 (page 25), Figure 18 (page 26), & Figure

19 (page 27).

• Useonlycopperwireforthelinevoltagepowersupply

to this unit. Use proper code agency listed conduit and

a conduit connector for connecting the supply wires to

the unit. Aluminum supply wire may be used if a heater

kit is installed.

• Ifreplacinganyoftheoriginalwiressuppliedwiththe

unit, the replacement wire must be copper wire consisting

of the same gauge and temperature rating.

• Providepowersupplyfortheunitinaccordancewiththe

unit wiring diagram, and the unit rating plate. Use UL

listed conduit and conduit connectors for connecting the

supply wires to the unit and for proper grounding. Field

supplied bushings for the power supply cables must be

added to support and protect the power supply cables.

• All208/230Voltunitsareshippedfromthefactorywired

for 240 volt operation. For 208V operation, remove the

lead from the transformer terminal marked 240V and

connect it to the terminal marked 208V.

Grounding

WARNING:

The unit cabinet must have an uninterrupted or

unbroken electrical ground to minimize personal

injury if an electrical fault should occur. Do not

use gas piping as an electrical ground!

This unit must be electrically grounded in accordance

with local codes or, in the absence of local codes, with

the National Electrical Code (ANSI/NFPA 70) or the CSA

C22.1 Electrical Code. Use the grounding lug provided in

the control box for grounding the unit.

Thermostat Connections

• Thermostat connections shall bein accordancewith

the instructions supplied with the thermostat. The

thermostat used with this equipment must operate in

conjunction with any installed accessories. Typical AC

and air handler hookups are shown in Figure 9 (page

12).

CAUTION:

Isolation must be maintained from the external

Class 2 output of any transformer in a cooling

circuit. Use a thermostat with isolating contacts

to prevent inter-connection of Class 2 outputs.

• Wherelocalcodesrequirethatthethermostatwiring

must be routed through a conduit or raceway, splices

can be made inside the unit; however, all wiring must

be NEC Class 1 and separated from incoming power

leads.

• Thethermostatshouldbemountedabout5feetabove

the ﬂoor on an inside wall. DO NOT install the thermostat

on an outside wall or any other location where its

operation may be adversely affected by radiant heat from

ﬁreplaces, sunlight, or lighting ﬁxtures, and convective

heat from warm air registers or electrical appliances.

Refer to the thermostat manufacturer’s instruction sheet

for detailed mounting and installation information.

• Installthegrommet,whichispackedwiththeunit,in

the hole for low-voltage wires. Properly connect the

low-voltage wiring between the thermostat, outdoor

unit, and control board. NOTE: When the low voltage

wires are positioned in this grommet, the grommet will

prevent chaﬁng and/or shorting of the low voltage leads.

Control Board

The control board in the air handler controls the timing

sequence of the elements. The board is equipped with

a 3 second blower on delay and a 15 second blower off

delay in heating and a 40 second blower off delay in

cooling. See Figure 13 (page 23) or Figure 14 (page

23) and Table 12 (page 29), (page 30) & page

31 for control board modes and actions.

Twinning

B6BM air handlers are not supplied with a built in twinning

capability. To connect two air handlers to a common

single stage AC condensing unit or heat pump, a twinning

kit is available for ﬁeld installation. Please follow the

instructions supplied with the kit.

NOTE: Variable speed air handlers cannot be twinned.

Heater Kits

Figure 9. Typical Thermostat Connections

W/EO

Thermostat

Air

Handler

Air

Conditioner

Typical Air Conditioner with

Standard Air Handler

GRC

Thermostat

Typical Heat Pump with

Standard Air Handler

Typical Air Conditioner with

2-Stage Air Handler

Typical Heat Pump with

2-Stage Air Handler

Thermostat

W/E

Thermostat

Typical 2-Stage Air Conditioner

with 2-Stage Air Handler

Typical 2-Stage Heat Pump with

2-Stage Air Handler

Y2 OUT

W/E

Air

Conditioner

Air

Handler

Air

Conditioner

Air

Handler

Heat Pump

Air

Handler

Heat Pump

Air

Handler

Heat Pump

NOTE: Jumper between

W2 & E is required when

no OD T- Stat is used.

NOTE: Jumper W1 & W2

together if not using W2

on thermostat

Y/Y2

Air

Handler

Y/Y2

NOTE: Jumper W1 & W2

together if not using W2

on thermostat

When electric heat packages with circuit breakers are

ﬁeld-installed, the circuit breaker may be used as a

disconnecting means in most applications. Reference

the NEC and local codes for disconnect requirements.

If a heater kit is installed:

The B6BM air handler is shipped from the factory without

an electric heater kit installed. If Electric heat is desired,

the H6HK heater kit may be purchased separately and

ﬁeld installed. Determine the correct size heater kit for your

unit by referring to the list below or the units rating label.

A Cabinet ....................................................... 15Kw max

B Cabinet ....................................................... 20Kw max

C Cabinet ....................................................... 30Kw max

1. Connect the 2 wire plug of the air handler to the mating

2 wire plug of the heater kit.

2. Connect the line voltage leads to the circuit breaker or

terminal block provided.

3. Connect the heater kit plug with the mating receptacle

on the air handler control board.

If a heater kit is not installed:

1. Remove the 2 wire plug of the air handler by cutting the

wires and discarding the plug.

2. Strip the ends of the 2 air handler wires and connect

to the line-voltage leads with the 2 wire nuts provided.

Electronic Air Cleaner (EAC)

The unit has an output to power an electronic air cleaner

when the blower is running. This output is rated to 1.0

amp at 208/240V.

Humidiﬁer

The unit has an output to power a humidiﬁer when the

blower is running. This output is rated to 1.0 amp at

208/240V.

Optional Humidistat

(B6EM or B6VM Models Only)

The optional humidistat may be installed in the return air

duct to provide excellent humidity control when needed

and maximum system capacity and energy efﬁciency when

humidity levels are normal. The humidistat senses when

humidity in the return air stream is above a preset level

(ﬁeld adjustable) and sends a signal to the motor to reduce

the airﬂow so that more moisture may be removed until the

humidity level drops. The air handler is pre-programmed

for humidistat operation.

Install the humidistat in the return air duct as directed in

the installation instructions included with the kit. Wire the

humidistat through the low-voltage wire entrance in the

air handler to the control board terminal marked DEHUM.

See Figure 15 (page 24) & Figure 16 (page 24). Wire

the humidistat to close on rise in humidity.

STARTUP & ADJUSTMENTS

WARNING:

The evaporator coil is shipped from the factory

with a nitrogen charge. Use caution when

preparing coils for ﬁeld connections. If repairs

make it necessary for evacuation and charging,

it should only be attempted by qualified,

trained personnel thoroughly familiar with this

equipment. Some local codes require licensed

installation service personnel to service this type

of equipment. Under no circumstances should

the equipment owner attempt to install and/or

service this equipment. Failure to comply with

this warning could result in equipment damage,

personal injury, or death.

NITROGEN

HEALTH

FLAMMABILITY

REACTIVITY

0 Minimal Hazard

1 Slight Hazard

Before You Start the Unit

Prior to start-up, complete the following inspections:

√ Verify the unit is level and properly located with adequate

clearances for servicing the unit as shown in Table 1,

(page 4).

√ Check condensate drain line(s) for proper drainage.

√ Verify the surrounding area and top of the unit is free

from obstructions and debris.

√ Check all duct connections. Make sure the duct work

is adequately sealed to prevent air leakage.

√ Check all coil connections for leaks.

√ Verify that the line voltage power leads are securely

connected and the unit is properly grounded. Make sure

all doors are installed before restoring power to the unit

√ Verify the thermostat is wired correctly. Make sure all

low voltage wires are securely connected.

√ Verify the power supply branch circuit overcurrent

protection is sized properly.

√ Verify ﬁlter is properly and securely installed.

IMPORTANT: Before starting the unit, install the initial

charge on units that are factory shipped with a nitrogen

holding charge:

1. Read all installation instructions ﬁrst.

2. Purge the nitrogen holding charge.

3. Evacuate the unit to 350 - 500 microns.

4. Allow the unit to remain under vacuum for at least 30

minutes.

5. Weigh in the proper amount of new (or reclaimed)

refrigerant. Refer to the air conditioner or heat pump

installation manual for the proper type and quantity of

refrigerant.

Refrigerant Charging

The system refrigerant charge can be checked and

adjusted through the service ports provided at the front

panel of the outdoor unit. Use only gauge lines which have

a Schrader depression device present to actuate the valve.

Air Circulation

Running the Blower Continuously

Set the thermostat’s system mode to OFF and the

thermostat’s fan mode to ON. The blower motor should

run continuously. Check for air delivery at the register(s).

Ensure that there are no obstructions at the registers or

in the ducts.

Selecting continuous low speed fan operation

(Standard Blower)

The air handler is equipped with an option of continuous

low speed fan operation. When G is energized without Y/

Y2, the air handler will operate using the cooling speed.

With G & Y/Y2 or Y/Y2 energized, the air handler will

operate in the selected cooling speed (including 40 sec

blower-off delay).

Turning the Blower Off

Set thermostat’s fan mode to AUTO, the blower will shut

down immediately.

System Cooling

1. Set the thermostat’s system mode to COOL and fan

mode to AUTO. Lower the thermostat’s temperature

mode below room temperature and observe that the

blower energizes. Check the air being discharged at

the register is cooler than room temperature. Verify

unit refrigerant pressures are in order. Blower should

be turning in direction indicated by arrow.

NOTE: DO NOT alter unit wiring. Listen for any unusual

noises. Locate the source and correct as needed.

2. Allow the unit to run for several minutes and then set

the thermostat’s temperature above room temperature.

Verify the blower cycles off with the thermostat.

System Heating

1. Set the thermostat’s system mode to HEAT and the fan

mode to AUTO. Increase the thermostat’s temperature

above room temperature and observe that the blower

energizes. Check the air being discharged at the register

is warmer than room temperature.

2. Allow the unit to run for several minutes and then set

the thermostat’s temperature below room temperature.

Verify the blower cycles off with the thermostat.

Selecting Minimum Electric Heat Airﬂow

The minimum electric heat airﬂow setting controls the

minimum air ﬂow that will be produced whenever electric

heater kits are used. When the electric heater kit is

energized along with a heat pump, the airﬂow may be

higher depending on the basic cooling/heat-pump airﬂow

setting. The minimum electric heat airﬂow is selected by

the red blower wire on 3-speed models or setting switches

1,2,3 & 4 on B6EM models. B6VM models automatically

set the heating speed based on the amount of installed

heat. The A/B switch must be set appropriately for the

unit cabinet size. For C-sized cabinets, the A/B switch can

be set in either position. The remaining 3 HEAT switches

have no function. Switch settings are listed in Table 6,

(page 20) or Table 9, (page 22).

NOTES:

• ForB6EMModels,theminimumelectricheatairow

setting may be set higher, but must never be set lower

than the setting shown in Table 7, (page 21).

• Variable speed motor control boards do not support

non-electric heat because the heating air ﬂow cannot

be set independently.

Blower Conﬁgurations

Determining Nominal System Capacity

To select the appropriate airﬂows for the air handler, the

nominal system capacity must be known. The nominal

system capacity is always the nominal capacity of the

outdoor unit. However, in some situations the nominal

system capacity may not be the same as the nominal

capacity of the air handler. Always refer to the nominal

capacity of the outdoor unit to determine the nominal

system capacity.

NOTE: The CFM values listed in Table 9, (page 22)

are not dependent on duct static pressure. The VSHE

motor automatically compensates for changes in duct

static pressure (within the limits of the motor).

3-Speed Units

The blower speed is preset at the factory for operation

at the same speed for heating and cooling, by using the

jumping terminal on the blower motor and connecting it

to the desired speed with both the red and black wires

connected to the jumping terminal. NOTE: The control

board is programmed with a 40 second off delay in the

cooling mode for optimum system performance and

efﬁciency.

CAUTION:

To avoid personal injury or property damage,

make sure the motor leads do not come into

contact with any uninsulated metal components

of the unit.

For optimum system performance and comfort, it may be

necessary to change the factory set speed. See Table 5,

(page 19) for airﬂow data. To change the blower speed:

1. Disconnect all electrical power to the unit and remove

the upper door.

2. Remove the black and red wires from the blower motor

jumping terminal. Discard the blower motor jumping

terminal.

3. Connect the heating speed wire (red) and the cooling

speed wire (black) to the desired blower speed marked

on the terminal block of the blower motor.

DHUM

HUMIDISTAT

MOTOR

CONTROL BOARD

Figure 10. DHUM Wiring Conﬁguration

• Terminal4=Hispeed

• Terminal5=Medspeed

• Terminal6=Lowspeed

4. Replace the upper door and secure it to the unit.

5. Restore power to the unit.

High Efﬁciency Units (Variable & Fixed Speed)

IMPORTANT! This air handler has been designed to

give the installer maximum ﬂexibility to optimize system

performance, efﬁciency, and comfort. Because there

are so many different ways to set up the air handler it is

important to read and follow these directions carefully.

B6EM & B6VM air handlers use high efﬁciency circulating

air motors that come in two variations and both are

controlled differently. The ﬁxed speed motor control

board Figure 15 (page 24) controls the torque and the

variable speed motor control board (Figure 16) controls

the airﬂow at a constant CFM. Both boards use the same

control board.

Before operation, the air handler must be conﬁgured to

match the unit with the system, system options, and climatic

conditions. When conﬁgured, the air handler responds

directly to the thermostat inputs, as well as the optional

humidistat (see page 13). During normal operation, the

motor will gradually change speeds during start-up, shut

down, when thermostat inputs change, and when the duct

static pressure changes (vents closed or opened, ﬁlter

clogging, etc.). The air handler is conﬁgured by setting

the selector switches and removing jumper connectors.

Selecting Basic Heating Airﬂow

Fixed & variable speed motor control boards (Figure 15

(page 24) & Figure 16) contain a set of dip switches

for setting the blower speed. For B6EM models, pins 1-4

set the speed for heating. For B6VM models, the A/B

switch must be set for the appropriate cabinet size (either

setting can be used for C-size cabinets). The airﬂow is set

automatically based on the amount of installed heat. For

both B6EM & B6VM models, the cooling speed is selected

via switches 5,6,7,& 8. To determine the appropriate

switch settings for your installation, see Table 6, (page

20), Table 7, (page 21), Table 8, (page 21), or

Table 9, (page 22).

Selecting Basic Cooling / Heat Pump Airﬂow

The basic cooling/heat-pump airﬂow is controlled by setting

switches 5 - 8 on the motor control board (mounted on the

blower). All airﬂows for other modes of operation (except

electric heat) are determined by this basic setting. FAN

ONLY would deliver 50% of the selected cooling airﬂow.

Table 8, (page 21) lists the basic airﬂow values versus

the airﬂow selector switch settings and ranges of basic

air ﬂow settings recommended for each nominal system

capacity.

• When operating in the heat pump mode, a higher

basic airﬂow setting will increase the energy efﬁciency

and capacity but will also decrease the supply air

temperature.

• Formaximumcapacityandenergyefciency,selectan

airﬂow at or near the top of the range for that nominal

capacity. See Table 8, (page 21).

• Formaximumdehumidication,selectanairownearthe

middle or bottom of the range for that nominal capacity.

Additional information on humidity control can be found

in the Humidistat and Delay Setting sections.

• Forthermostatswithadehumidieroutput,useaeld

supplied wire to connect the thermostat’s dehumidiﬁer

output to the terminal marked DHUM. The thermostat

should be set so that the DHUM output should be high

(energized) when dehumidiﬁcation is needed. See also

Dehumidiﬁcation Options section.

IMPORTANT! If coil icing is observed, the basic cooling/

heat-pump airﬂow selected may be too low. Verify the

setting selected is within the range shown in Table 8 and

that the the system is properly charged. Please refer to

the instructions supplied with the outdoor unit. If icing

continues to occur, raise the selected airﬂow one or two

steps.

NOTE: Variable speed air handlers with SEER ratings

higher than 15 are matched with a 2-stage cooling outdoor

unit. They are programmed to operate at 75% of the

selected airﬂow while the system is in the lo-cool mode

and 100% of the selected airﬂow while in hi-cool mode.

Dehumidiﬁcation Options

(B6EM or B6VM Models Only)

Both motor control boards Figure 15 (page 24) & Figure

16 (page 24) have a DHUM connection that allows the

system to increase the amount of humidity that is removed

from the circulating air. This is accomplished by reducing

the CFM and allowing the cooling coil to become colder.

There are many ways that this can be electrically wired.

1. If the room thermostat incorporates a humidity sensor

and DHUM output, connect the DHUM on the thermostat

to the DHUM terminal on the motor control board.

2. If using a separate humidistat, connect the DHUM & R

terminals on the humidistat to the DHUM & R terminals

on the motor control board of the air handler. In this

option, the DHUM output of the humidistat must be set

to be normally open and closed when there is a call for

humidiﬁcation. See Figure 10.

3. For cooling only system: If a humidistat is not available,

it is an acceptable option to connect the R & DHUM

terminals on the motor control board together with a

ﬁeld supplied wire. This option causes the blower to run

at a reduced CFM for 10 minutes after a call for cooling.

NOTE: Heat pump systems must use a thermostat

with humidity sensor or separate humidistat to prevent

blower speed reduction in heat mode.

Table 2. Filter Sizes

CABINET SIZE FILTER SIZE

A 12 x 20 x 1

B 18 x 20 x 1

C 20 x 20 x 1

RED LED (AN2) DIAGNOSTIC

OFF Control Fault (No Power)

Flash Blower Fault

ON Normal Operation

Table 3. Air handler Control Board Fault Conditions

UNIT MAINTENANCE

Proper maintenance is most important to achieve the best

performance from a air handler. Some of the components

and their locations are shown in Figure 12 (page 18). If

any component of the air handler must be replaced, use

only factory authorized replacement parts speciﬁed in the

Replacement Parts List provided online.

WARNING:

ELECTRICAL SHOCK, FIRE OR

EXPLOSION HAZARD

Failure to follow safety warnings exactly could

result in serious injury or property damage.

Improper servicing could result in dangerous

operation, serious injury, death or property

damage.

• Beforeservicing,disconnectallelectricalpower

to the indoor blower.

• Whenservicingcontrols,labelallwiresprior

to disconnecting. Reconnect wires correctly.

• Verifyproperoperationafterservicing.

• Thesemaintenanceinstructionsareprimarilyintended

to assist qualiﬁed technicians experienced in the proper

maintenance and operation of this appliance.

• Always reinstall the doors on the air handler after

servicing or cleaning/changing the ﬁlters. Do not operate

the air handler without all doors and covers in place.

• Verifythatthethermostatisproperlyinstalledandis

not being affected by drafts or heat from lamps or other

appliances.

• To achieve the best performance and minimize

equipment failure, it is recommended that a yearly

maintenance checkup be performed. At a minimum,

this check should include the following items:

Air Filter(s) - B6 Series Air Handlers are not supplied

with a single air ﬁlter when shipped from the factory. It

is recommended that the ﬁlter be cleaned or replaced

every 4 to 6 months at a minimum. Newly built or recently

renovated homes may require more frequent changing

until the construction dust has minimized. Filter sizes

shown in Table 2 are available at most local retailers.

WARNING:

Never operate the air handler without a ﬁlter in

place. Dust and lint in the return air can build

up on internal components, resulting in loss of

efﬁciency, equipment damage, and possible ﬁre.

Filters designed to remove smaller particles such as

pollen, may require additional maintenance.

Blower Compartment - Dirt and lint can create excessive

loads on the motor resulting in higher than normal

operating temperatures and shortened service life. It is

recommended that the blower compartment be cleaned of

dirt or lint that may have accumulated in the compartment

or on the blower and motor as part of the annual inspection.

Blower Fan Wheel - Inspect the blower wheel blades

for accumulations of dirt and clean if necessary. Inspect

mounting nut for tightness when done.

Blower Motor & Assembly - Inspect the blower assembly

and motor mounting brackets for tightness and corrosion.

Correct deﬁciencies if necessary. The blower motor

contains sealed bearings and under normal operating

conditions, no maintenance is necessary for the life of

the equipment.

TROUBLESHOOTING

If the air handler fails to operate, check the following:

• Istheelectricturnedon?

• Isthethermostatoperatingproperly?

• Aretheblowercompartmentdoor(s)inplace?

• Istheairhandlerdisconnectclosed?

• Hasthecircuitbreakertrippedorthecontrolboardfuse

burnedopen?

• Areanymanualresetswitchesopen?

• Isthelterdirtyorplugged?

• IstheLEDonbothcontrolboardsconstantlyON?Ifnot,

refer to Table 3 or Table 4 to determine fault condition.

Table 4. Motor Control Board Fault Conditions

DIAGNOSTIC

GREEN

LED

RED

LED

FIXED

SPEED

FURNACES

Control Fault (no Power) Off Off

normal oPeration On On

motor Fault On Flash

twin Fault (no motor Fault) Flash On

CommuniCations Fault Flash Flash

VARIABLE

SPEED

FURNACES

Control Fault (no Power) Off Off

normal oPeration On On

motor Fault On Flash

CommuniCations Fault Flash Flash

FIGURES & TABLES

Figure 11. B6 Series Physical Dimensions

3/4”

13”

1 7/8" K.O.

11/8” K.O.

(typ.)

11/4”

15/8”

17/8”

11/4”

3 1/4”

2 5/8”

11/8” K.O.

(typ.)

13/4” K.O.

(typ.)

1 7/8”

3 5/8”

5 5/8”

DETAIL “D”

3 1/4”

2 1/4”

15 1/4”

13”

SUCTION

LIQUID

“W”

1 1/8”

1 7/8”

7/8" K.O.

“H”

22"

“A”

CABINET SIZE H W A DETAIL D

A 43-5/16 14-3/16 12-3/4 No

B 43-5/16 19-11/16 18-1/4 No

Tall B 49-5/16 19-11/16 18-1/4 No

C 55-15/16 22-7/16 21 Yes

Horizontal

Drain Pan

Vertical

Drain Pan

Coil

Assembly

Motor

Mount Kit

Blower

Motor

Transformer

Capacitor

Circuit

Breaker (60A)

Heating Element

Assembly

Filter

Tracks

Blower

Wheel

Blower

Housing

Motor Control

Board

Control

Board

Filter

Door

Upper Door

Assembly

wer Door

Assembly

Figure 12. Air Handler Components

Airﬂow Data

DRY COIL ESP 0.10 0.20 0.30 0.40 0.50 0.60 0.70 0.80

*24K

A-CABINET

Low 683 647 607 563 515 463 406 345

Corrected ESP

0.00 0.07 0.19 0.30 0.42 0.53 0.65 0.76

Medium 861 823 781 734 682 625 564 498

Corrected ESP

0.00 0.00 0.11 0.23 0.36 0.48 0.60 0.72

High 1072 1026 975 920 860 797 730 659

Corrected ESP

0.00 0.00 0.00 0.14 0.27 0.40 0.53 0.67

*30K

A-CABINET

Low 849 825 793 753 704 647 581 508

Corrected ESP

0.00 0.04 0.15 0.27 0.38 0.50 0.62 0.74

Medium 1118 1087 1046 997 940 874 799 717

Corrected ESP

0.00 0.00 0.04 0.17 0.29 0.42 0.55 0.68

High 1277 1233 1184 1130 1070 1005 935 860

Corrected ESP

0.00 0.00 0.00 0.10 0.23 0.36 0.49 0.63

*24K

B-CABINET

Low 708 690 664 628 584 532 471 401

Corrected ESP

— 0.08 0.19 0.30 0.41 0.53 0.64 0.76

Medium 909 904 886 854 810 753 683 600

Corrected ESP

— — 0.10 0.22 0.33 0.46 0.58 0.71

High 1118 1132 1126 1101 1056 992 908 805

Corrected ESP

— — — 0.09 0.22 0.35 0.49 0.64

*30/*36K

B-CABINET

Low 953 915 871 821 764 701 631 555

Corrected ESP

0.00 0.04 0.16 0.27 0.39 0.51 0.62 0.74

Medium 1265 1232 1188 1133 1067 991 903 805

Corrected ESP

0.00 0.00 0.03 0.15 0.28 0.41 0.54 0.68

High 1427 1385 1333 1270 1196 1113 1018 913

Corrected ESP

0.00 0.00 0.00 0.09 0.23 0.36 0.50 0.64

*42/48K

B-CABINET

Low 1324 1302 1271 1233 1187 1134 1072 1003

Corrected ESP

0.00 0.06 0.17 0.27 0.38 0.49 0.61 0.72

Medium 1485 1455 1418 1373 1320 1260 1193 1118

Corrected ESP

0.00 0.00 0.13 0.24 0.36 0.47 0.58 0.70

High 1637 1601 1558 1506 1447 1380 1305 1223

Corrected ESP

0.00 0.00 0.00 0.21 0.33 0.44 0.56 0.68

*48K

C-CABINET

Low 1605 1606 1592 1565 1524 1468 1399 1316

Corrected ESP

0 0.11 0.21 0.31 0.42 0.52 0.63 0.74

Medium 1977 1939 1890 1830 1758 1675 1580 1474

Corrected ESP

0 0 0.18 0.28 0.39 0.50 0.61 0.72

High 2264 2182 2095 2003 1906 1805 1698 1586

Corrected ESP

0 0 0 0.26 0.37 0.49 0.60 0.71

*60K

C-CABINET

Use B6EM C-Cabinet airﬂow data. See Table 5 (page 20).

NOTES:

1 Airﬂow is shown in cfm, +/- 5%.

2 External static pressure (ESP) is shown in inches w.c.

3 See unit nameplate or installation instructions for maximum recommended external static pressure.

Table 5. B6BM Airﬂow Data

B6EM

A-CABINET

SWITCH SETTINGS

0 = OFF, 1 = ON

COOLING OR HEATING AIRFLOW (CFM)

DRY COIL ESP

1/5 2/6 3/7 4/8 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8

0 0 0 0 585 550 520 460 420 405

— —

1 0 0 0 710 670 650 610 560 530 475 440

0 1 0 0 845 790 765 715 680 655 625 580

1 1 0 0 890 865 840 785 760 710 680 655

0 0 1 0 955 925 900 850 825 790 770 720

1 0 1 0 1030 995 975 940 910 870 840 815

0 1 1 0 1115 1085 1060 1020 995 965 925 905

1 1 1 0 1155 1130 1095 1070 1040 1010 985 950

0 0 0 1 1200 1175 1145 1110 1085 1060 1025 1000

1 0 0 1 1240 1215 1195 1170 1140 1110 1080 1060

0 1 0 1 1320 1290 1265 1240 1215 1185 1160 1130

1 1 0 1 1355 1330 1305 1280 1255 1220 1200 1175

0 0 1 1 1405 1375 1345 1325 1295 1275 1250 1210

1 0 1 1 1440 1415 1385 1355 1325 1290 1255 1215

0 1 1 1 1465 1425 1390 1355 1320 1290 1260 1215

1 1 1 1 1465 1425 1390 1355 1320 1290 1260 1215

B6EM

B-CABINET

SWITCH SETTINGS

0 = OFF, 1 = ON

COOLING OR HEATING AIRFLOW (CFM)

DRY COIL ESP

1/5 2/6 3/7 4/8 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8

0 0 0 0 600 550 430 390

— — — —

1 0 0 0 660 610 540 460 425

— — —

0 1 0 0 830 750 695 640 580 520

— —

1 1 0 0 860 825 765 690 630 600 525 485

0 0 1 0 935 895 835 790 710 655 620 585

1 0 1 0 1045 975 920 875 830 795 720 685

0 1 1 0 1095 1040 995 950 900 850 805 750

1 1 1 0 1155 1105 1060 1010 965 920 870 825

0 0 0 1 1230 1185 1140 1090 1045 1010 965 920

1 0 0 1 1285 1260 1210 1165 1125 1080 1040 1010

0 1 0 1 1330 1290 1245 1205 1170 1125 1085 1045

1 1 0 1 1395 1365 1315 1275 1235 1205 1160 1130

0 0 1 1 1450 1405 1375 1335 1295 1260 1220 1180

1 0 1 1 1490 1450 1410 1385 1340 1300 1270 1230

0 1 1 1

1530 1485 1460 1425 1380 1350 1310 1280

1 1 1 1 1530 1490 1465 1425 1390 1350 1310 1285

B6EM

C-CABINET

SWITCH SETTINGS

0 = OFF, 1 = ON

COOLING OR HEATING AIRFLOW (CFM)

DRY COIL ESP

1/5 2/6 3/7 4/8 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8

0 0 0 0 710 580 395

— — — — —

1 0 0 0 830 690 675 530 505

— — —

0 1 0 0 930 875 710 665 560 530

— —

1 1 0 0 1065 1015 900 840 800 705 665 635

0 0 1 0 1185 1115 1010 960 925 875 830 745

1 0 1 0 1275 1220 1175 1120 1060 970 930 890

0 1 1 0 1365 1350 1255 1200 1150 1105 1060 1025

1 1 1 0 1480 1430 1370 1325 1265 1225 1185 1140

0 0 0 1 1560 1535 1485 1430 1375 1335 1285 1240

1 0 0 1 1650 1600 1545 1500 1450 1405 1360 1305

0 1 0 1 1730 1685 1660 1610 1570 1520 1470 1420

1 1 0 1 1785 1740 1695 1645 1615 1545 1510 1470

0 0 1 1 1865 1820 1785 1750 1695 1655 1605 1560

1 0 1 1 1920 1890 1850 1805 1765 1715 1675 1640

0 1 1 1 2010 1965 1960 1900 1850 1810 1775 1730

1 1 1 1 2065 2020 1985 1955 1915 1880 1840 1810

NOTE: When matched with two-stage outdoor units, the airﬂow on low (Y1 or W1) input will be 70% of the values shown in this table.

Table 6. B6EM (FSHE) Airﬂow Data

Page is loading ...

Kelvinator JT4BE048KA Operating instructions

Brand: Kelvinator

Model: JT4BE048KA

Category: Split-system air conditioners

Type: Operating instructions

Download PDF

report

Kelvinator JT4BE048KA Operating instructions

Kelvinator JT4BE048KA Operating instructions

Related papers

Other documents