H3C MSR Series User manual

Brand: H3C

Model: MSR Series

Type: User manual

H3C MSR Series Routers offer a range of capabilities to enhance your networking experience. With these routers, you can utilize Open Application Platform (OAP) and Open Application Platform-Smart (OAPS) modules to run an independent Linux operating system, allowing you to load and run custom software such as security and voice applications. The GigabitEthernet management port provides fast and reliable connectivity, while the USB port enables convenient data transfer. The LED indicators on the front panel offer clear visual feedback on the status of the system, disk, and network connectivity.

H3C MSR Series Routers

OAP/OAPS V2 Module

User Guide

Hangzhou H3C Technologies Co., Ltd.

http://www.h3c.com

Document version: 6PW102-20120703

licensors

No part of this manual may be reproduced or transmitted in any form or

by any means without prior written consent of Hangzhou H3C

Technologies Co., Ltd.

Trademarks

H3C, , Aolynk, , H

Care, , TOP G, , IRF,

NetPilot, Neocean, NeoVTL, SecPro, SecPoint, SecEngine, SecPath,

Comware, Secware, Storware, NQA, VVG, V

G, V

G, PSPT, XGbus,

N-Bus, TiGem, InnoVision and HUASAN are trademarks of Hangzhou

H3C Technologies Co., Ltd.

All other trademarks that may be mentioned in this manual are the

property of their respective owners

Notice

The information in this document is subject to change without notice.

Every effort has been made in the preparation of this document to ensure

accuracy of the contents, but all statements, information, and

recommendations in this document do not constitute the warranty of any

kind, express or implied.

Environmental protection

This product has been designed to comply with the environmental

protection requirements. The storage, use, and disposal of this product

must meet the applicable national laws and regulations.

Preface

The H3C MSR Series Routers OAP/OAPS V2 Module User Guide

describes hardware specifications of OAP/OAPS V2 modules,

configuration on routers, and how to log in to the operating system of an

OAP/OAPS V2 module.

This preface includes:

• Audience

• Conventions

• About the H3C MSR documentation set

• Obtaining documentation

• Technical support

• Documentation feedback

Audience

This documentation is intended for:

• Network planners

• Field technical support and servicing engineers

• Network administrators working with the OAP/OAPS V2

Conventions

This section describes the conventions used in this documentation set.

Command conventions

Convention Descri

tion

Boldface

Bold text represents commands and keywords that you enter

literally as shown.

Italic

Italic text represents arguments that you replace with actual

values.

Convention Descri

tion

[ ]

Square brackets enclose syntax choices (keywords or

arguments) that are optional.

{ x | y | ... }

Braces enclose a set of required syntax choices separated by

vertical bars, from which you select one.

[ x | y | ... ]

Square brackets enclose a set of optional syntax choices

separated by vertical bars, from which you select one or none.

{ x | y | ... } *

Asterisk marked braces enclose a set of required syntax choices

separated by vertical bars, from which you select at least one.

[ x | y | ... ] *

Asterisk marked square brackets enclose optional syntax

choices separated by vertical bars, from which you select one

choice, multiple choices, or none.

&<1-n>

The argument or keyword and argument combination before

the ampersand (&) sign can be entered 1 to n times.

# A line that starts with a pound (#) sign is comments.

Symbols

Convention Descri

tion

NOTE

An alert that contains additional or supplementary

information.

About the H3C MSR documentation set

The H3C MSR documentation set includes:

Cate

Documents

Pur

oses

Operations and

maintenance

H3C MSR Series

Routers

OAP_OAPS V2

Module

Customization

User Guide

Describes how to install the operating

system of an OAP/OAPS V2 module

and the configuration procedures for

customizing the OAP/OAPS V2

module

Obtaining documentation

You can access the most up-to-date H3C product documentation on the

World Wide Web at http://www.h3c.com

Click the links on the top navigation bar to obtain different categories of

product documentation:

[Technical Support & Documents > Technical Documents]

– Provides

hardware installation, software upgrading, and software feature

configuration and maintenance documentation.

[Products & Solutions]

– Provides information about products and

technologies, as well as solutions.

[Technical Support & Documents > Software Download]

– Provides the

documentation released with the software version.

Technical support

servi[email protected]

http://www.h3c.com

Documentation feedback

You can e-mail your comments about product documentation to

info@h3c.com.

We appreciate your comments.

Contents

Overview ··········································································································· 1

Panel views ······································································································· 2

OAP Smart MIM Module ········································································ 2

OAP MIM Module ··················································································· 2

OAP FIC Module ····················································································· 3

LEDs ··················································································································· 3

Stand By button ································································································ 4

GigabitEthernet management port ································································· 5

Configuring ACFP and ACSEI on the router ··················································· 6

ACFP configuration ·························································································· 6

Introduction to ACFP ··············································································· 6

Enabling ACFP server ············································································· 7

Configuring the ACFP client ··································································· 7

ACSEI configuration ························································································ 7

Introduction to ACSEI ·············································································· 7

Enabling ACSEI server ············································································ 8

Logging in to and resetting the Linux operating system of an OAP/OAPS

module ··············································································································· 9



Redirecting to an OAP/OAPS module from the router ································ 9

Resetting the system of an OAP/OAPS module ··········································· 9

Configuration examples ················································································ 10

Overview

The Open Application Platform (OAP) and Open Application

Platform-Smart (OAPS) are designed for new services.

H3C MSR Series Routers provides the following OAPS and OAP

modules:

• OAP Smart MIM Module

• OAP MIM Module

• OAP FIC Module

An OAPS or OAP module can be installed in the expansion module slot

on the router. An OAPS or OAP module runs an independent Linux

operating system. You can load software such as security and voice in the

operating system.

Table 1 Compatibility matrix between OAPS/OAP and routers

Module Router

OAP Smart MIM

Module

• MSR 30-11

• MSR 30-16

• MSR 30-20

• MSR 30-40

• MSR 30-60

OAP MIM Module

• MSR 30-16

• MSR 30-20

• MSR 30-40

• MSR 30-60

OAP FIC Module

• MSR 50-40

• MSR 50-60

• MPU-G2

Panel views

OAP Smart MIM Module

Figure 1 Front panel

(1) USB port (2) 100/1000Base-T Ethernet port LED

(3) LINK LED for the GigabitEthernet management port

(4) Stand By button (5) System status LED (SYS)

(6) Disk LED (DISK) (7) Gi

abitEthernet mana

ement port

OAP MIM Module

Figure 2 Front panel

(1) USB port (2) 100/1000Base-T Ethernet port LED

(3) LINK LED for the GigabitEthernet management port

(4) Stand By button (5) System status LED (SYS)

(6) Disk LED (DISK) (7) Gi

abitEthernet mana

ement port

OAP FIC Module

Figure 3 Front panel

(1) 100/1000Base-T Ethernet port LED

(2) LINK LED for the GigabitEthernet management port (3) Stand By button

(4) System status LED (SYS)

(5) Disk LED

(6) Gi

abitEthernet mana

ement port

(7) USB port

LEDs

Table 2 LED description

LED mark Status

Descri

tion

SYS

Steady green A memory test is being performed.

Fast flashing (green) The BIOS is starting up.

Slow flashing (green) The operating system is starting up.

Steady yellow Reserved.

Fast flashing (yellow) The boot loader does not exist.

Slow flashing (yellow) The memory test has failed.

Off The module is powered off.

1 2

34567

LED mark Status

Descri

tion

DISK

Steady green The disk is in position.

Flashing green

The disk is performing a read/write

operation.

Steady yellow A problem has occurred to the disk.

Off The disk is not in position.

LINK/ACT

Steady yellow A link is present on the port.

Flashing yellow

Data is being transmitted or received

over the link.

100/1000M

Off

(Suppose the LINK/ACT

LED is yellow)

A 10 Mbps link is present.

Steady orange

(Suppose the LINK/ACT

LED is yellow)

A 100 Mbps link is present.

Steady green

(Suppose the LINK/ACT

LED is yellow)

A 1000 Mbps link is present.

Stand By button

Table 3 Stand By button operation description

stem status O

eration

Descri

tion

The OAP module is

power off.

Press the Stand By button.

The module is turned on

and the system starts up.

The OAP module is

powered on.

Press and hold the Stand By

button for less than four

seconds.

Soft off (the system is shut

down first and then the

module is powered off.)

Press and hold the Stand By

button for more than four

seconds.

Force a shutdown.

GigabitEthernet management port

Table 4 GigabitEthernet management port specifications

Item

ecification

OAP

OAPS

Connector type RJ-45

Port type MDI/MDIX auto-sensing

Port transmission

rate

• 10/100 Mbps, half/full duplex

• 1000 Mbps, half duplex

Frame format

Ethernet_II

Ethernet_SNAP

Configuring ACFP and ACSEI on the

router

NOTE:

fter installing the OAP/OAPS module on the router, perform the

following configurations on the router.

ACFP configuration

Introduction to ACFP

Application Control Forwarding Protocol (ACFP) is a collaboration

framework for the client/server model between devices. ACFP mainly

describes the specifications for implementing collaboration between the

OAP/OAPS module and the routers. The OAP/OAPS module is called

ACFP client while the router is called ACFP server. A router mirrors or

redirects the received packets to an ACFP client after matching the ACFP

collaboration rules. The software running on the ACFP client monitors

and detects the packets. Based on the monitoring and detection results,

the ACFP client sends back responses to the router through collaboration

Management Information Bases (MIBs) to instruct the router to process the

results, such as filtering out the specified packets.

By controlling data flows on the router, ACFP implements collaboration to

provide users with a unified interface for issuing rules.

Enabling ACFP server

Follow these steps to enable the ACFP server:

To do… Use the command…

Remarks

Enter system view system-view —

Enable the ACFP

server

acfp server enable

Required

Disabled by default

Configuring the ACFP client

You must configure the ACFP collaboration policy and ACFP

collaboration rules on the ACFP client through MIB. The specific

configuration depends on the service software used on the ACFP client.

NOTE:

• For more information about ACFP configuration, see the

H3C MSR

Series Routers OAA Configuration Guide

• Enable the ACFP server only on the router installed with OAP/OAPS

modules that require the ACFP function.

ACSEI configuration

Introduction to ACSEI

As a private protocol, ACSEI provides a method for exchanging

information between ACFP clients and ACFP server. It well supports

Application Control Forwarding Protocol (ACFP) collaboration, ensuring

valid information interaction between the ACFP clients and the ACFP

server, so that the ACFP server and clients can cooperate to run a service.

As a supporting protocol of ACFP, ACSEI also has two entities: server

and client.

• ACSEI server is integrated into the software system of the router and is

supported by the router.

• ACSEI client is integrated into the software system of the OAP module. It

is a function supported by the OAP module.

Enabling ACSEI server

Follow these steps to enable ACSEI server:

To do… Use the command…

Remarks

Enter system view

system-view

—

Enable ACSEI server

acsei server enable

Required

Disabled by default.

NOTE:

• For more information about ACSEI configuration, see the

H3C MSR

Series Routers OAA Configuration Guide

• The ACSEI client function is enabled by default.

• Enable the ACSEI server only on the router installed with OAP/OAPS

modules that require the ACSEI function.

Logging in to and resetting the Linux

operating system of an OAP/OAPS

module

You can perform the following operation and configuration to the

OAP/OAPS module on the router:

• Redirecting to an OAP/OAPS module from the router

• Reset the Linux system of the OAP/OAPS module

Redirecting to an OAP/OAPS module

from the router

You can redirect to the operating system of an OAP/OAPS module from

the router through the following operation. In this way, the terminal

display interface will be switched from the command line interface (CLI)

on the router to the operating interface of the operating system of the

OAP/OAPS module. To return to the CLI on the router, press Ctrl+K.

Follow the step to redirect from the router to the OAP/OAPS module:

To do… Use the command…

Remarks

Redirect from the router to

the OAP/OAPS module

oap connect slot

slot-number

Required

Available in user view

Resetting the system of an OAP/OAPS

module

If the operating system works abnormally or is under other anomalies (for

example, the system does not respond), you can reset the Linux system of

an OAP/OAPS module with the following command to make the module

restart.

Follow the step to reset the system of an OAP/OAPS module:

To do… Use the command… Remarks

Reset the Linux system of

an OAP/OAPS module

oap reboot slot slotnum

Required

Available in user view

NOTE:

Resetting the OAP/OAPS module may cause data loss and service

interruption. Before resetting the OAP/OAPS module, save the

configurations of the module operating system and shut down the module

operating system to avoid service interruption and data loss.

Configuration examples

Redirecting to an OAP/OAPS module from the router

The OAP/OAPS module is installed in slot 4 on the router.

<System> oap connect slot 4

Connected to OAP

CentOS release 5.4 (Final)

Kernel 2.6.18-164.el5 on an x86_64

localhost login: root

Password:

Last login: Mon Dec4 11:17:00 on ttyS0

You have new mail.

[root@localhost ~]#

Resetting the Linux system of an OAP/OAPS module

The OAP/OAPS module is installed in slot 4 on the router.

<System> oap reboot slot 4

This command will recover the OAP from shutdown or other failed

state.

Warning: This command may lose the data on the hard disk if the

OAP is not shut

down!

Continue? [Y/N]y

OAP is being reboot.

H3C MSR Series User manual

H3C MSR Series User manual

H3C MSR Series User manual

Related papers

Other documents