DEXAPLAN MA 604 Owner's manual

DEXAPLAN
Brand
DEXAPLAN
Model
MA 604
Type
Owner's manual

This manual is also suitable for

Dexaplan
Mini-alarm MA 604
T 62
C
O
P
I
{
}
B
R
T
E
W
Q
U
Y
A
D
10 m
100°
10 m
100°
6 m
2°
T62_MA604_GB.indd 1 12.09.2006 11:32:33 Uhr
Operating and safety instructions
Introduction
Please read these operating instructions thoroughly and carefully. They are part of this
product and contain important instructions relating to its operation and handling.
Please always observe all safety instructions. Before initial operation, please check
that all parts are fitted correctly. If you have any questions or are unsure about handling of
the device, please contact the dealer or the service office. Please keep these instruc-
tions in a safe place and pass them on to anyone else intending to use the device.
Proper use
The mini-alarm MA 604 responds by way of the integrated passive infrared movement de-
tector (PIR) to the movements of heat-emitting bodies in rooms or at points of entry
(doors). The detector registers such movements either by a siren or two-tone bell. It can be
connected to a bell push or other type of make contact for use as a door chime. The device
is suitable for use or installation in dry, enclosed spaces. It can be connected for operation to
a 9 volt block-battery or a 9 volt mains adapter (neither is included).
The device is for private use only. Any other use or modification of the device constitutes im-
proper use and poses a serious risk of accident.
The manufacturer is not liable for damage caused by improper use or incorrect operation of
the device.
Pack contents
We supply the mini-alarm with the following components (see Fig. A)
1 x Mini - alarm
1 x bell push contact cable (in the battery compartment)
2 x fastening screws (in the battery compartment)
1 x operating instructions
Equipment
On the front of the casing (see Fig. A):
Q
Mini-alarm
W
Mounting bracket
E
Infrared sensor with Fresnel lens (integrated PIR)
R
Function switch
T
Loudspeaker
Y
2 screws
U
Bell push contact cable
On the reverse side of the casing (see Fig. B):
I
9 volt DC mains adapter socket
O
Bell push contact cable socket
P
Battery compartment
{
Battery clip
}
Battery compartment cover
T62_MA604_GB.indd 2 12.09.2006 11:32:33 Uhr
1 x
1 x
2 x
1 x
Q
W
E
R
T
Y
U
I
O
P
{
}
Technical data
Infrared sensor with Fresnel lens: passive infrared movement detector (PIR)
PIR sensing range (max.): - horizontal: approx. 10 m x 100° (at 20° C)
- vertical: approx. 6 m x 2°
Power supply: 9 volt block-battery (9 V block 6LR61, alkaline)
(not included in the delivery scope)
Current consumption: max. 60 mA, or 9 volt DC mains adapter,
min. 200 mA (internal pole of plug positive)
(not included)
Current consumption: max. 100 mA
Functions: , 0,
an
d bell push contact
Acoustic signal: 1 x two-tone chime
30 sec long siren of approx. 90 dB(A)
Bell push contact: 2 x two-tone chime
ON delay: approx. 15 sec
Dimensions: 7.7 x 4.2 x 7.0 cm (h x w x l)
Weight: 86 g (without batteries)
Protection class: III
Safety instructions
The following instructions are for your own safety and satisfaction when operating the
device. Please note that non-compliance with these safety instructions can lead to a
serious risk of accident.
Explanation of the symbols and terms used:
c Danger! failure to observe this instruction endangers life and health.
m Caution! failure to observe this instruction poses a risk to property.
Tip! - following this advice will help you to achieve optimal results.
c Danger
• Do not leave small children unsupervised with the packaging material. Danger of
suffocation.
• Do not leave children unsupervised with the device. Danger to life and risk of injury.
• Do not use the device in the presence of sick or disabled people and animals.
Shock caused by the alarm signal can endanger life and poses a risk of injury.
• Do not damage any gas, electricity or telecommunication lines when fitting the
device. Danger to life and risk of injury and damage.
• Do not allow leaky or damaged batteries to come into contact with the skin or
eyes. Use suitable protective gloves and clothing. Danger to life and risk of injury
from corrosive acid.
• Never expose the device to fire, heat or to temperatures of over 50° C for any
length of time. Danger to life from explosion.
• Do not short-circuit the batteries or recharge them. Danger to life from explosion.
• Make sure that your hearing is not exposed to the loud alarm signal for any
length of time. This can cause serious damage to the hearing.
T62_MA604_GB.indd 3 12.09.2006 11:32:34 Uhr
• Make sure that the alarm signal is not triggered close to the ears. This can cause
serious damage to the hearing.
• Please handle the connecting cable with care. Install it so that it cannot get dam-
aged and does not create a stumbling hazard. Otherwise there is danger to life
and a risk of injury and fire.
• Do not connect any other energy source to the socket of the bell push contact
cable. There is otherwise danger to life.
m Caution
• Operate the device with a 9 V compound battery or a 9 volt mains adapter only.
• Make sure that the battery is inserted with the correct polarity.
• Remove the battery from the device for long periods of non-use.
• Use new batteries only and under no circumstances used ones.
• Make sure before connecting a 9 volt mains adapter to the mains power supply
that the mains current is 230 V ~ 50 Hz and has a max. 16 ampere fuse in ac-
cordance with regulations.
• Do not cover the device with any objects. This could diminish the function of the
infrared sensor with Fresnel lens or the loudspeaker.
• Make sure that the device does not come into contact with moisture.
• Protect the device from strong magnetic or electric fields.
• Protect the device from high mechanical strain and shocks.
• Only use the device with the supplied original parts or parts suitable for it.
• Check before initial operation that all components are assembled in accordance
with the operating instructions.
• Before assembly and initial operation of the device, check that the delivery is
complete and undamaged.
• The device must only be repaired by authorized and skilled specialists.
Failure to observe this instruction poses a risk of damage resulting from improper
use and a loss of the warranty.
• Install the device so that no heat sources such as radiators or air ducts are situ-
ated in the range of the sensor. When activated, the mini-alarm could register the
temperature emitted by these objects as movements by heat-emitting bodies.
• Use the device at normal room temperatures only. Higher or lower temperatures
can impair its function.
Initial operation
Tip: the mini-alarm reacts sensitively and quickly to movements crossing its
sensing range. It reacts less sensitively to movements directly towards the sensing
range (see Fig. C).
You can use the mini-alarm to indicate movements of welcome (e.g. family members)
and unwelcome visitors (e.g. intruders) with an audible signal. You can choose be-
tween a two-tone chime and an approx. 30 sec. long siren. The device can be used
horizontally for an area and vertically for a point of entry (“curtain effect”) in the moni-
tored room (see Fig. D).
The mini-alarm can be used as a door bell by connecting it to a bell push or other
closing contact contact with the bell push contact cable.
T62_MA604_GB.indd 4 12.09.2006 11:32:34 Uhr
Preparation and material required
The stated materials are not included in the delivery scope. The information provided
here is non-binding and intended as a guide. The quality of the material depends on
individual local requirements.
You will need:
o Either a 9 volt block-battery 6LR61, alkaline, or a 9 volt mains adapter, min. 200 mA
(positive internal pole of the plug) for power supply (not included in the delivery scope).
o A pen to mark the installation position.
o A crosstip screwdriver for installation with the fastening screws.
Power supply
m Caution!
o Operate the device with a 9 V block-battery (6LR61, alkaline) or a 9 volt mains
adapter only.
o Make sure that the battery is inserted with the correct polarity.
o Remove the battery from the device for long periods of non-use.
o Use new batteries only and under no circumstances used ones.
o Make sure before connecting a 9 volt mains adapter to the mains power supply
that the mains current is 230 V ~ 50 Hz and has a max. 16 ampere fuse in accord-
ance with regulations.
9 volt block-battery
o Set the function switch
R
to position 0.
o Remove the battery compartment cover
}
completely from the reverse side of
the mini-alarm casing
Q
(see Fig. B).
o Connect a new 9 volt compound battery to the battery clip
{
.
o
Fasten the battery compartment cover properly on the reverse side of the mini-alarm
casing.
9 volt mains adapter
o Before connecting, make sure that the polarity is correct.
o Set the function switch
R
to position 0.
o Connect the 9 volt mains adapter to the 9 volt DC mains adapter socket
I
.
o Connect the 9 volt mains adapter to the mains supply.
Setting up / installation
o Estimate the supposed area of movement of heat-emitting bodies and choose the
position for the mini-alarm. From the mini-alarm, the sensing range extends to 10 m
at approx. 100° for an area and 6 m at 2° for points of entry (see Fig. C and D).
Monitoring an area in a room
o Position the mini-alarm at a height of approx. 1.0 – 1.5 m. Adjust the
Fresnel - lens
E
horizontally to the area to be monitored.
Monitoring a doorway
o Position the mini-alarm above the object to be monitored. Adjust the
Fresnel - lens
E
vertically to the sensing range.
T62_MA604_GB.indd 5 12.09.2006 11:32:35 Uhr
Installation
c Danger: Take care not to damage any gas, electricity or telecommunication lines
when fitting the device. Danger to life and risk of injury and damage.
Tip: to cut costs, connect the device for continuous operation to a 9 volt mains
adapter for the power supply.
The mini-alarm can be installed to monitor an area permanently – this is recommend-
ed for continuous operation, e.g. at the entrance to your home. You can position the
mini-alarm by adjusting its angle on the mounting bracket.
o Remove the mounting bracket carefully from the mini-alarm.
o Hold the mounting bracket in the position you wish to install it and mark the
holes in the rectangular surface of the mounting bracket
W
with the pen.
o Screw the mounting bracket carefully in position with the fastening screws
Y
.
o Mount the mini-alarm carefully on the mounting bracket and check that it is
properly positioned.
Tip: you can also set up the mini-alarm to monitor an area for a short period of
time – this is recommended for travel use, e.g. in your hotel room.
o Place the mini-alarm on e.g. a piece of furniture and check that it is properly
positioned.
Activating / deactivating alarm functions
m Danger
o Do not use the device in the presence of sick or disabled people and animals.
Shock caused by the siren can endanger life and poses a risk of injury.
o Make sure that your hearing is not exposed to the loud siren for any length of
time. This can cause serious damage to the hearing.
o Make sure that the alarm is not triggered close to the ears. This can cause serious
damage to the hearing.
Functions
You can control the function of the mini-alarm with the function switch and by con-
necting it to a bell push or other type of make contact.
- Activating the chime function
o Set the function switch to position
The mini-alarm registers movement of a heat-emitting body with a two-tone chime.
- Activating the alarm function
o Set the function switch to position
o Leave the sensing range of the mini-alarm within the ON delay of approx.
15 seconds. The mini-alarm subsequently registers movement by a heat-emitting
body with a siren lasting approx. 30 sec.
0 - Deactivating the alarm / chime function
o Set the function switch to position 0.
o Monitoring of the sensing range is deacctivated.
T62_MA604_GB.indd 6 12.09.2006 11:32:35 Uhr
Connecting an external bell push or other closing contact.
m Danger
o Do not connect any other energy source to the socket of the bell push contact
cable. Otherwise there is danger to life and a risk of fire.
o Handle the cable with care. Install it so that it cannot get damaged and does not create
a stumbling hazard. Otherwise there is danger to life and a risk of injury and fire.
o Connect the mini-alarm to a bell push or other type of closing contact with the
bell push contact cable
U
. When the connected bell push or closing contact is
activated, a two-tone chime rings twice. This function is active irrespective of the
chosen position of the function switch ( , or 0 ).
Troubleshooting
Fault Cause Remedy
The mini-alarm is not
working or is not
working properly.
The battery has run out. Replace the battery.
The mains adapter is not
connected with the right
polarity.
Correct the polarity of
the mains adapter.
The acoustic signal of
the mini-alarm is
weak.
The battery has run out. Replace the battery.
Slow reaction or short
range
Direction of movement is
directly towards the mini-
alarm.
Change the position of
the mini-alarm
Sensing range is tempera-
ture dependent.
Change the position of
the mini-alarm.
Alarm activation with
no human movement
Other heat source: heater,
sunshine, air movement,
animals
Stop the heat source or
change the position of
the mini-alarm
Maintenance and cleaning
o
Disconnect the mini-alarm from the power supply before maintenance and cleaning.
o Check the technical safety and function of the device regularly.
o Remove the 9 volt block-battery during long periods of non-use.
o Use a fluff-free cloth and a mild detergent (no solvents) to clean the plastic and
metal surfaces.
T62_MA604_GB.indd 7 12.09.2006 11:32:36 Uhr
Disposal
Please take all packaging materials to a disposal facility in your city or district. The
recyclable packaging materials are selected for their ecologically compatible and disposal-
related properties. In accordance with European Directive 2002 / 96 / EC on used electrical
and electronic appliances and its implementation in national law, used electrical
devices must be collected separately and recycled in an ecologically compatible manner.
o Remove the batteries before disposing of the device.
o Take the device to a disposal facility in your city or district after its useful life.
As the consumer you are required by law (Battery Ordinance) to return all used batteries.
Batteries containing harmful substances are identified with the symbols shown, indicating
that their disposal in household waste is prohibited. The abbreviations for the critical
heavy metals are: Cd = Cadmium, Hg = Mercury, Pb = Lead.
Please take all used batteries to a disposal facility in your city or district, or return
them to the dealer.
By following these requirements you are meeting your legal obligations and making
an important contribution to protecting the environment.
Warranty
This device has a warranty of 3 years from the date of purchase. The device was
manufactured with care and inspected thoroughly before delivery. Please keep your
receipt as proof of purchase. If you have a claim under the warranty, please contact
the service office for your country. This is the only way to ensure that your device can
be sent in free of charge.
This warranty is only valid for the first purchaser and is not transferable.
The warranty furthermore covers material or manufacturing defects only. It does not
apply to wear parts or damage to fragile parts, e.g. switches or batteries. The product
is solely intended for private use and not for commercial use. No claim for damages
may be made in the event of a burglary. An alarm is no substitute for insurance cover
and does not replace your duty of care.
In the event of incorrect and / or improper handling, the use of force or any work on
the device that is not performed by the service office, the warranty shall expire. This
warranty does not restrict your statutory rights.
Service
Information on dealing with problems can be found under www.dexaplan.com.
If you have any questions, please contact our service office by email (service@dexaplan.de)
or by telephone (
T
0870 241 3029) (
T
1890 851 851). Here you will find all
necessary information on service questions such as returns, etc.
Dexaplan GmbH
Paul-Böhringer-Str. 3 · D - 74229 Oedheim
Last Information Update 07/2006 · Ident.-No.: 07-2006-MA 604-GB / IE
T62_MA604_GB.indd 8 12.09.2006 11:32:36 Uhr
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

DEXAPLAN MA 604 Owner's manual

DEXAPLAN
Brand
DEXAPLAN
Model
MA 604
Type
Owner's manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents