Price DFW series Installation guide

Type
Installation guide
v100 Issue Date: 02/02/18
© 2018 Price Industries Limited. All rights reserved.
MANUAL – INSTALLATION
Displacement Flow In-Wall Diffuser
DFW Series
DISPLACEMENT FLOW IN-WALL DIFFUSER
1 DISPLACEMENT FLOW IN-WALL DIFFUSER - Manual | priceindustries.com priceindustries.com | DISPLACEMENT FLOW IN-WALL DIFFUSER - Manual
INSTALLATION INSTRUCTIONS
1
2
3
NOM HEIGHT
2 X 4
Figure 1
OPEN FACE
PLENUM
1/2" DRYWALL
NOM WIDTH
2
X 4
Figure 3
OPEN
DIFFUSER FACE
Figure 2
FLOOR
PLENUM
Box
1/2" DRYWALL REF
1/2" DRYWALL REF
HEIGHT TO BOTTOM
OF DIFFUSER FACE + 3/8”
2X4
STUD REF
2X4
STUD REF
MIN 1/8"
MAX 1/4"
RECOMMENDED:
ADD BEAD OF CAULKING
TO SEAL PLENUM
MAKE SURE THAT THE SECONDARY
BAFFLE IS POINTING DOWN AWAY
FROM THE INLET. SECONDARY
BAFFLE IS AVAILABLE ON UNITS
THAT ARE GREATER THAN 30 IN.
WIDE AND HAVE A HEIGHT OF 24 IN.
WIDTH
HEIGHT
2.000
Figure 4
CONNECT DUCT TO
DIFFUSER INLET
1
2
3
NOM HEIGHT
2 X 4
Figure 1
OPEN FACE
PLENUM
1/2" DRYWALL
NOM WIDTH
2
X 4
Figure 3
OPEN
DIFFUSER FACE
Figure 2
FLOOR
PLENUM
Box
1/2" DRYWALL REF
1/2" DRYWALL REF
HEIGHT TO BOTTOM
OF DIFFUSER FACE + 3/8”
2X4
STUD REF
2X4
STUD REF
MIN 1/8"
MAX 1/4"
RECOMMENDED:
ADD BEAD OF CAULKING
TO SEAL PLENUM
MAKE SURE THAT THE SECONDARY
BAFFLE IS POINTING DOWN AWAY
FROM THE INLET. SECONDARY
BAFFLE IS AVAILABLE ON UNITS
THAT ARE GREATER THAN 30 IN.
WIDE AND HAVE A HEIGHT OF 24 IN.
WIDTH
HEIGHT
2.000
Figure 4
CONNECT DUCT TO
DIFFUSER INLET
* Screws are shipped loose.
Step-by-Step Instructions
READ INSTRUCTIONS
COMPLETELY BEFORE STARTING
1. It is recommended to install the
plenum box prior to drywall.
2. When framing an opening for a
plenum box, note that the diffuser
face overhangs plenum box by
3/8". For example, if in a finished
state the diffuser face is required to
be mounted 12" above the floor, the
bottom of the plenum box needs to
be installed 12 3/8" above the floor.
3. Install plenum box (DFW) in the
wall opening. Adjust plenum depth
such that the plenum protrudes a
minimum of 1/8" to a maximum
of 1/4" past the face of the wall
stud to allow the drywall to butt
up against the plenum (Figure 1).
Secure plenum in place with screws
(supplied by others.)
Table 1
Item # Description
1 Plenum x 1
2 Face x 1
3 Screws
DFW
FIGURE 1
DISPLACEMENT FLOW IN-WALL DIFFUSER
2priceindustries.com | DISPLACEMENT FLOW IN-WALL DIFFUSER - Manual
INSTALLATION INSTRUCTIONS
4. After the drywall has been installed
and finished as required around the
plenum, apply a bead of caulking
along plenum wall and drywall edge
to minimize air leakage.
5. Insert the diffuser face into the
plenum. Use the supplied screws
to mount the diffuser face to
the plenum (Figure 3). For units
supplied with a secondary baffle
see Figure 4 to determine proper
baffle orientation.
6. NOTE: Standard screws issued
with DFW displacement unit are
3/4" self-drilling. These will work
with 1/2" thick drywall. If drywall is
thicker than 1/2", a different length
screw must be requested at time of
ordering.
7. Care should be taken not to over
tighten the screws (Item 3).
1
2
3
NOM HEIGHT
2 X 4
Figure 1
OPEN FACE
PLENUM
1/2" DRYWALL
NOM WIDTH
2
X 4
Figure 3
OPEN
DIFFUSER FACE
Figure 2
FLOOR
PLENUM
Box
1/2" DRYWALL REF
1/2" DRYWALL REF
HEIGHT TO BOTTOM
OF DIFFUSER FACE + 3/8”
2X4
STUD REF
2X4
STUD REF
MIN 1/8"
MAX 1/4"
RECOMMENDED:
ADD BEAD OF CAULKING
TO SEAL PLENUM
MAKE SURE THAT THE SECONDARY
BAFFLE IS POINTING DOWN AWAY
FROM THE INLET. SECONDARY
BAFFLE IS AVAILABLE ON UNITS
THAT ARE GREATER THAN 30 IN.
WIDE AND HAVE A HEIGHT OF 24 IN.
WIDTH
HEIGHT
2.000
Figure 4
CONNECT DUCT TO
DIFFUSER INLET
1
2
3
NOM HEIGHT
2 X 4
Figure 1
OPEN FACE
PLENUM
1/2" DRYWALL
NOM WIDTH
2
X 4
Figure 3
OPEN
DIFFUSER FACE
Figure 2
FLOOR
PLENUM
Box
1/2" DRYWALL REF
1/2" DRYWALL REF
HEIGHT TO BOTTOM
OF DIFFUSER FACE + 3/8”
2X4
STUD REF
2X4
STUD REF
MIN 1/8"
MAX 1/4"
RECOMMENDED:
ADD BEAD OF CAULKING
TO SEAL PLENUM
MAKE SURE THAT THE SECONDARY
BAFFLE IS POINTING DOWN AWAY
FROM THE INLET. SECONDARY
BAFFLE IS AVAILABLE ON UNITS
THAT ARE GREATER THAN 30 IN.
WIDE AND HAVE A HEIGHT OF 24 IN.
WIDTH
HEIGHT
2.000
Figure 4
CONNECT DUCT TO
DIFFUSER INLET
1
2
3
NOM HEIGHT
2 X 4
Figure 1
OPEN FACE
PLENUM
1/2" DRYWALL
NOM WIDTH
2
X 4
Figure 3
OPEN
DIFFUSER FACE
Figure 2
FLOOR
PLENUM
Box
1/2" DRYWALL REF
1/2" DRYWALL REF
HEIGHT TO BOTTOM
OF DIFFUSER FACE + 3/8”
2X4
STUD REF
2X4
STUD REF
MIN 1/8"
MAX 1/4"
RECOMMENDED:
ADD BEAD OF CAULKING
TO SEAL PLENUM
MAKE SURE THAT THE SECONDARY
BAFFLE IS POINTING DOWN AWAY
FROM THE INLET. SECONDARY
BAFFLE IS AVAILABLE ON UNITS
THAT ARE GREATER THAN 30 IN.
WIDE AND HAVE A HEIGHT OF 24 IN.
WIDTH
HEIGHT
2.000
Figure 4
CONNECT DUCT TO
DIFFUSER INLET
FIGURE 2
FIGURE 3
FIGURE 4
This document contains the most current product information as of this printing.
For the most up-to-date product information, please go to priceindustries.com
© 2018 Price Industries Limited. All rights reserved.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Price DFW series Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI