ALURAD ATLANTIS Directions For Mounting And Use

Brand: ALURAD

Model: ATLANTIS

Type: Directions For Mounting And Use

ALURAD ATLANTIS

The ALURAD ATLANTIS is a radiator designed for efficient and reliable heating in residential and commercial spaces. Its advanced features and versatile mounting options make it an ideal choice for a wide range of applications.

Key Features:

Easy Mounting: The radiator can be easily mounted on walls using the included hanger elements, ensuring a secure and stable installation.
Optimal Heat Distribution: The radiator's design promotes uniform heat distribution throughout the room, providing consistent comfort levels.
Corrosion Resistance: An inhibitor capsule is fitted during manufacturing to protect against corrosion, ensuring the radiator's longevity.

ALURAD ATLANTIS

Key Features:

Easy Mounting: The radiator can be easily mounted on walls using the included hanger elements, ensuring a secure and stable installation.
Optimal Heat Distribution: The radiator's design promotes uniform heat distribution throughout the room, providing consistent comfort levels.
Corrosion Resistance: An inhibitor capsule is fitted during manufacturing to protect against corrosion, ensuring the radiator's longevity.

A-MOUNTING WITH

HANGER SYSTEM

Mount the radiator without removing it from its nylon

packing. Remove the nylon cover before use after

completion of all alteration and painting works.

The initial putting of the radiator into operation may

be carried out while the nylon cover is on.

Atlantis radiators can be easily mounted on the wall

using the four hanger elements.

For this purpose, first mark the locations of the

brackets on the wall in accordance with the

measurements given in the figure.

Bore the holes on the wall for mounting the brackets

using a drill, according to the measurements given

in the figure.

First mark the location of holes.

Then bore the holes.

Mount the brackets on the wall by tightening their

screws using a screwdriver. The upper mounting

elements should rest on the radiator's upper profile.

70 mm

(n-3)x80 mm

h-220

135 mm

Radiator

Hanger

Element

h= Radiator height (mm)

e.g. For atlantis 390, h= 390 mm

For Atlantis 450, h=450 mm

n= Number of radiator columns

e.g. For a radiator with 10 columnsi n= 10

y= Radiator height from the floor (min. 50 mm)

Note: For models with integrated valve,

the center measurement shall be (n-4) x 80 mm

Figure 1

(h-220)mm

(n-3)x80 mm

Figure 2

Bracket

1st Hole

2nd Hole

Figure 3

P e r f e c t R a d i a t o r

Atlantis

DIRECTIONS FOR MOUNTING AND USE

* An inhibitor capsule unique to Alurad is fitted to all radiators during manufacture in order to provide protection against all kinds of corrosion. If the system as a whole

is desired to be protected against freezing as well as various kinds of corrosion, the use of ANTICOR 121 is recommended. Feniþ Teknik may not be held liable for

any problems that might arise from the use of another corrosion inhibitor or antifreeze.

Upper

Lowel

45mm

25mm

68mm

80mm

25mm

45mm

135mm

y min= 50 mm

Wall

Zemin

Figure 5

Figure 6

Figure 7

Place the radiator so that the hanger elements

will engage the wall brackets. For radiators with

more then 25 columns, an intermediate supporting

element shall be placed at the upper middle section

of the radiator and fixed to the wall in that area.

The type of connection shall be same as for the

upper mounting element shown in the figure.

After completion of mounting, fill the installation

with water, and then drain the water after the first

cycle is run. Then fill the radiator with water again,

and release the air trapped in the radiator, using the

purgers provided at the upper end points of the

radiator. The air release operation must be performed

in intervals. After the initial filling of radiator with water,

all the air trapped in the radiator must be released,

and the pressure of the system should be set to

1.5 - 2.0 bars over the nominal preasure. Then the

air release operation must be performed at 40°C,

60°C and 80°C, seperately. After being sure that the

whole system is in proper operating condition, the

monometer pressure should be set to a value which

is 1.0 – 1.5 bars over the nominal pressure.

Lower Opposite End Connection

Alurad radiators allow the making of lower

opposite end connection without causing any

reduction in yield. To meet this purpose, the

“direction plug“ and “pusher“ shown in Figure 7

will be put into the packing if a request is made

for them in the purchase order.

Placement of Direction Plug

In making the lower opposite end connection,

the direction plug shall be placed at the following

locations as counted from the hot water inlet,

using the pusher supplied:

a) For radiators with up to 10 columns, between

columns 3 and 4 (215 mm), and

b) For radiators with more then 10 columns,

between columns 4 and 5 (295 mm).

135mm

Figure 4

ALURAD ATLANTIS Directions For Mounting And Use

Brand: ALURAD

Model: ATLANTIS

Type: Directions For Mounting And Use

ALURAD ATLANTIS

Key Features:

Easy Mounting: The radiator can be easily mounted on walls using the included hanger elements, ensuring a secure and stable installation.
Optimal Heat Distribution: The radiator's design promotes uniform heat distribution throughout the room, providing consistent comfort levels.
Corrosion Resistance: An inhibitor capsule is fitted during manufacturing to protect against corrosion, ensuring the radiator's longevity.

Download PDF

report

ALURAD ATLANTIS Directions For Mounting And Use

ALURAD ATLANTIS Directions For Mounting And Use

Related papers

Other documents