Star Trac 4 Series PVS Install Manual

Brand: Star Trac

Model: 4 Series PVS

Type: Install Manual

This manual is also suitable for

INSTALL

MANUAL

4-Series PVS

Core Health & Fitness

Page 1

Required Tools:

• #2 Phillips Screwdriver

• 5mm Allen Key

Please note that while the instructions below show a treadmill, they are valid for all 4-series equipment.

1. Use a #2 phillips screwdriver to remove the six

(6) #8-18 x 3/4” screws securing the front of the

console to the back shroud, then remove the

front of the console.

TECH TIP: Take a picture or note where the cables

are plugged into the console as these will need to be

reconnected after installing the PVS.

2. Route the coax cable through the unit - See Page

NOTE: The 4-CT will have the coax cable pre-routed.

3. Use a #2 phillips screwdriver to remove the two

(2) #8-18 x 3/4” screws securing the upper cover

to the rear console shroud, then remove the

cover.

4. Use a 5mm allen key to secure the PVS bracket

to the console using four (4) pieces of the M8 x

20mm button head cap screw.

Page 2

5. Slide the PVS bracket-compatible upper cover

over the PVS bracket and secure to the rear

console shroud using the #8-18 x 3/4” screws

removed in Step 2.

6. Slide the PVS bracket grommet over the PVS

bracket - be careful of orientation.

7. Use a #2 phillips screwdriver to remove the eight

(8) #8-18 x 3/4” screws securing the rear PVS

shroud, then remove the shroud.

Page 3

8. Use a #2 phillips screwdriver to remove the four

(4) M4 x 8mm pan head machine screws from the

back of the PVS, then use these screws to secure

the PVS to the PVS bracket.

9. Connect the cables from the neck of the PVS

bracket to the corresponding connections on the

bottom/back of the PVS.

123 4

2: To PVS

Controller

1: PVS

Power

4: Coax

Adapter

3: PVS Audio

Extension

10. Install the rear PVS shroud using a #2 screwdriver

and the screws removed in Step 6, then seat the

PVS grommet to ensure a tight seal between the

PVS and the PVS bracket.

Page 4

11. Use a #2 phillips screwdriver to remove the screw

securing the blank entertainment insert to the

console front, then install the PVS controller into

the console front and securing using the same

screw.

12. Disconnect the cables from the back of the USB

Panel Assembly, use a #2 phillips screwdriver to

remove the two (2) #8-18 x 3/4” screws securing

the panel to the console, then remove the panel.

TECH TIP: Take a picture or note where the cables

are plugged into the panel as these will need to be

reconnected to the new panel - See Step 12.

13. Install the new panel containing the audio PCB

into the console front, securing with the same

screws, then connect the cables removed in Step

11.

14. Connect the Supplementary Power (Sup. Power)

from the unit neck to the PVS Power.

15. Connect the end of the coax cable routed

through the unit to the end of the coax adapter.

16. Connect one end of the 3.5mm audio cable to

the PVS Audio Extension.

PVS Audio

Extension

COAX routed

through unit

PVS Power

To PVS

Controller

Sup. Power

To audio PCB

Page 5

17. Connect the other end of the PVS controller

cable into the PVS controller.

18. Connect the other end of the 3.5mm audio cable

to the audio PCB on the USB Panel Assembly

installed in Step 12.

19. Reconnect the cables from the unit neck to the

console, then secure the console front to the

console rear shroud using the #8-18 x 3/4” screws

removed in Step 1

20. Refer to the PVS owner’s manual to perform a

channel scan.

To Back/Bottom of PVS

To PVS Audio Extension

Page 6

Coax Cable Routing Paths:

4-RB 4-UB

4-TR

Star Trac 4 Series PVS Install Manual

Brand: Star Trac

Model: 4 Series PVS

Type: Install Manual

This manual is also suitable for

Download PDF

report

Star Trac 4 Series PVS Install Manual

This manual is also suitable for

Star Trac 4 Series PVS Install Manual

Related papers

Other documents