Star Trac E Series Upright E-UBi Gen. 1 User manual

620-7991 Rev 002

S

TAR

T

RAC

F

ITNESS™

P

ERSONAL

V

IEWING

S

CREEN

U

SER'S

M

ANUAL—

E-S

ERIES

E-UBi, E-RBi, E-STi, E-TBTi

E-TRi

STAR TRAC

14410 Myford Road

Irvine, CA 926060 USA

2

620-7991 Rev 002

3

620-7991 Rev 002

T

ABLE OF

C

ONTENTS

Introduction .............................................................................................................................................. 4

Before You Get Started ............................................................................................................................ 5

Warnings and Cautions ............................................................................................................................ 6

Important Safety Precautions .................................................................................................................. 7

Unpacking Your Personal Viewing Screen ............................................................................................. 8

Installing your STAR TRAC Personal Viewing Screen ......................................................................... 10

E-UB, E-RB, E-TBT, and E-ST ...................................................................................................... 10

E-TR and ETRx ............................................................................................................................. 19

Setting Up your NTSC / ATSC Personal Viewing Screen ..................................................................... 25

Basic Operations ........................................................................................................................... 25

Adjusting Picture Menu Options .................................................................................................... 26

Adjusting Audio Menu Options ...................................................................................................... 27

Adjusting Setup Menu Options ...................................................................................................... 29

Adjusting Channel Menu Options .................................................................................................. 33

Setting Up your PAL / SECAM Personal Viewing Screen .................................................................... 35

Basic Operations ........................................................................................................................... 35

Adjusting Picture Menu Options .................................................................................................... 36

Adjusting Sound Menu Options ..................................................................................................... 37

Adjusting Time Menu Options ....................................................................................................... 38

Adjusting System Options Menu ................................................................................................... 40

Adjusting Lock Menu Options ........................................................................................................ 41

Adjusting Channel Menu Options .................................................................................................. 43

FAQ’s and Troubleshooting ................................................................................................................... 46

Cleaning the PVS .......................................................................................................................... 46

Troubleshooting ............................................................................................................................ 46

Headphone Jack Replacement ..................................................................................................... 48

Regulatory Information .......................................................................................................................... 49

written permission from Star Trac.

Every effort has been made to keep this information current; however, periodically, changes are made to the information herein, and these changes will

be incorporated into new editions of this publication. All product names and logos are trademarks of their respective owners. Printed in the USA.

4

620-7991 Rev 002

Thank you for adding the STAR TRAC PERSONAL VIEWING SCREEN (PVS) to your Star Trac

Purchase. The Personal Viewing Screen has been designed to provide the user with the most re-

warding experience based upon the carefully planned features it possesses. The design elements

of this Personal Viewing Screen will provide you with a comfortable, intuitive, safe and reliable ex-

perience, guiding you to a habit-forming lifestyle. Star Trac's mission is to provide products to mold

lifelong habits for health and fitness.

ABOUT THIS MANUAL

This manual is applicable to the STAR TRAC E-UB UPRIGHT BIKE, E-RB RECUMBENT BIKE, E-

ST STEPPER, E-TBT TOTAL BODY TRAINER, and the E-TR TREADMILL. The manual is divided

into nine sections, as follows:

Introduction

Provides an overview of each section within the manual.

Before You Get Started

Provides guidelines to help you have a successful installation.

Warnings and Cautions

Helpful safety tips to keep you out of harms way.

Important Safety Precautions

Provides important safety tips to keep you out of harms way.

Unpacking your Personal Viewing Screen

Provides a description of what you will find in your PVS kit.

Installing Your STAR TRAC Personal Viewing Screen (PVS)

Provides a step-by-step instruction set for installing your PVS on the E-UB, E-RB, E-ST, E-

TBT and E-TR.

Setting Up Your STAR TRAC Personal Viewing Screen (PVS)

Provides step-by-step instruction set for configuring your PVS with either the NTSC/ATSC or

PAL/SECAM screen.

FAQ’s and Troubleshooting

Frequently asked questions and troubleshooting methods to help solve problems that may

occur with your PVS.

Regulatory Information

Provides regulatory information for the Star Trac Personal Viewing Screen.

I

NTRODUCTION

5

620-7991 Rev 002

B

EFORE

Y

OU

G

ET

S

TARTED

CHECK FACILITIES PREPAREDNESS

For a proper installation, please read this guide thoroughly and follow the instructions. Star Trac’s

goal is to help you have a successful and reliable installation, for this reason we have come up with

some helpful tips and check list to accomplish this goal.

EQUIPMENT LAYOUT

Check to see that the equipment you will be adding the PVS to are placed where they will be used. It

is recommended that you follow your installation guides for each one of your Star Trac pieces of

equipment in making sure that there is ample space around them to ensure a safe and enjoyable

experience.

INPUT SIGNAL

In the world of entertainment today you have many choices. Star Trac recommends you know what

type of video signal (cable, analogue, digital, satellite, antenna) is in the club facility and if it has a

good signal. Don’t forget every installation is different. Check to see that you have a coaxial cable

connection at each location where a PVS will be installed.

CABLING

When Radio Frequency signals travel through cabling the signal will degrade over distance. Connec-

tors may degrade the signal as well. Check each output before connecting to your PVS and make

sure you have a clean strong signal to ensure an enjoyable experience. The Star Trac PVS requires

a minimum signal strength of 45dBmV for analogue channels, and 40% for digital channels. Your

club may require signal amplifiers to achieve a good strong signal. Star Trac recommends you use a

qualified installer for your Audio Visual needs.

ELECTRICAL RECEPTACLES

The Personal Viewing Screen requires a plug-in 60 watt power supply to operate (included). Check

with your club facility to ensure ample electrical receptacles are placed next to the equipment for a

safe and proper install. Check with your contractor to make sure you have enough power.

6

620-7991 Rev 002

W

ARNINGS

A

ND

C

AUTIONS

This lighting flash with arrowhead symbol, within an equilateral triangle, is intended to alert

the user to the presence of un-insulated “dangerous voltage” within the product’s enclo-

sure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

This exclamation point within an equilateral triangle is intended to alert the user to the

presence of important operating and maintenance (servicing) instruction in the literature

accompanying the appliance.

WARNING:

To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.

DO NOT disassemble the PVS.

Any unauthorized maintenance will void the warranty. Inexperienced technicians can cause

serious damage, electric shock, and other hazards.

Contact your dealer or an experienced technician for repair.

DO NOT place sharp tools such as a pin or other metallic object near the display.

May result in scratching the surface of the monitor as well as the frame.

Keep your monitor away from liquid or a humid place.

May cause electric shock and damage the display.

When strange sound or smoke occurs, be sure to unplug your power cord.

These problems can cause a serious electric shock and other hazards.

DO NOT spray any fluid directly on the surface of the monitor.

Spray the cleaner fluid on a soft cloth to wipe the surface of the monitor.

7

620-7991 Rev 002

I

MPORTANT

S

AFETY

P

RECAUTIONS

Electrical energy can perform many useful functions, but it can also cause personal injuries and property

damage if improperly handled. This product has been engineered and manufactured with the highest prior-

ity on safety. But IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZ-

ARD. In order to prevent potential danger, please read the following instructions when installing, operating

and cleaning the product. To ensure your safety and prolong the service life of your new product, please

read the following precautions carefully before using the product.

1. Read these instructions---All operating instructions must be read and understood before the product is

operated.

2. Keep these instructions---These safety and operating instructions must be kept in a safe place for fu-

ture reference.

3. Heed all warnings---All warnings on the product and in the instructions must be observed closely.

4. Follow all instructions---All operating instructions must be followed.

5. Power source---This product is intended to be supplied by a listed power supply indicated on the mark-

ing label. If you are not sure of the type of power supply to your home, consult your product dealer or

local power company. For added protection for this product during a lightning storm, or when it is left

unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the cable

system.

6. Power cord protection---Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

Note: where the mains plug or an appliance coupler is used as the disconnect device, the disconnect

device shall remain readily operable.

7. Overloading---Do not overload wall outlets, extension cords, or convenience receptacles on other

equipment as this can result in a risk of fire or electric shock.

8. Replacement parts---In case the product needs replacement parts, make sure that the service person

replaces parts specified by the manufacturer, or those with the same characteristics and performance

as the original parts. Use of unauthorized parts can result in fire, electric shock and/or other dangers.

9. Safety checks---Upon completion of service or repair work, request the service technician to perform

safety checks to ensure that the product is in proper operating condition.

10. Clean only with damp cloth---Unplug this product from the wall outlet before cleaning. Do not use liq-

uid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

11. Panel protection---The display panel used in this product is made of glass. Therefore, it can break

when the product is dropped or impacted upon by other objects. Be careful not to be injured by broken

glass pieces in case the display panel breaks.

12. Pixel defect---The display panel is a very high technology product, giving you finely detailed pictures.

Occasionally, a few non-active pixels may appear on the screen as a fixed point of blue, green or red.

Please note that this does not affect the performance of your product.

Warning:

To prevent the spread of fire, keep candles or other open flames

away from this product at all times.

8

620-7991 Rev 002

U

NPACKING

Y

OUR

P

ERSONAL

V

IEWING

S

CREEN

Inspect the shipping box for any parts that may be missing BEFORE discarding the box. Items can shift dur-

ing transportation, and may be accidentally discarded with the box. If any parts are missing, please contact

Star Trac Product Support at 800-503-1221. Have the serial number of the PVS, and a list of the missing

parts ready so they may be shipped to you. The Personal Viewing Screen is shipped in one box separate

from your exercise equipment.

PVS kits are available in two different signal formats; NTSC/ATSC (typically US, Japan) and PAL/SECAM

(typically Europe, Middle East), make sure the kit you have is appropriate for the country of the club facility.

The following items will be in the box:

NTSC/ATSC Kit (US, Japan)

•

PVS assembly with mounting bracket, cables, and display cap with grommet

(There are 5 cables in the neck)

•

Center console keypad assembly

•

Entertainment headphone jack and Mount

•

Hardware tool kit, including:

•

(1) Headphone icon

•

(4) M8 x 20mm buttonhead screws

•

(5) M4 x 0.7X19L screws

•

(1) M8 hex nut

•

(1) Silicone wrap

•

(2) 5” tie straps

•

5MM hex Allen key.

•

60w power supply

(NOT INCLUDED IN THE E-TRi KIT)

•

Power cord, AS/NZS 3112

(NOT INCLUDED IN THE E-TRi KIT)

•

Power cord, Nema 6-15

(NOT INCLUDED IN THE E-TRi KIT)

•

Power cord, Nema 5-15

(NOT INCLUDED IN THE E-TRi KIT)

•

Owners manual

•

Warranty card.

9

620-7991 Rev 002

PAL/SECAM Kit (Europe, Middle East)

•

PVS assembly with mounting bracket, cables, and display cap with grommet

(There are 5 cables in the neck)

•

Center console keypad assembly

•

Entertainment headphone jack and mount

•

Hardware tool kit, including:

•

(1) Headphone icon

•

(4) M8 x 20mm buttonhead screws

•

(5) M4 x 0.7X19L screws

•

(1) M8 hex nut

•

(2) 5” tie straps

•

Silicon wrap

•

F-type male to female PAL/SECAM coaxial adapter

•

5MM hex Allen key.

•

60w power supply (NOT INCLUDED IN THE E-TRi KIT)

•

Power cord, CEE 7/7 (NOT INCLUDED IN THE E-TRi KIT)

•

Power cord, Nema 6-15 (NOT INCLUDED IN THE E-TRi KIT)

•

Power cord, BS 1363 (NOT INCLUDED IN THE E-TRi KIT)

•

Owners manual

•

Warranty card.

Required Tool for Installation

•

5MM hex Allen key

•

#2 Phillips screwdriver (Not Included)

•

1/2” wrench (for E-TRi kits only, not included)

•

Wire cutters (Not Included)

•

Pliers (Not Included)

•

Step stool (Not Included)

10

620-7991 Rev 002

The Star Trac Personal Viewing Screen is different for each of your Star Trac E-Series Cardio prod-

ucts. Make sure you have the proper kit for the E-Series product you are installing. The E-UBi, E-

RBi, E-TBTi, and the E-STi will follow the same basic steps for installation. For the E-TRi turn to ap-

propriate section of this manual.

STEP 1.

Using a #2 Phillips screwdriver, remove the (8)

screws on the back of the display plastic. Set

the screws aside, you will need them for re-

assembly.

After all the cable/harnessing has been disconnected, place the front display plastics aside for later

use. Be careful with the display and place it face down on top of a non-scratching surface.

I

NSTALLING

Y

OUR PVS

O

N

T

HE E-UB, E-RB, E-TBT,

A

ND E-ST

STEP 2.

After the screws have been removed, carefully

open the display plastic, so as to not detach the

inner cables from the display.

Disconnect the ground wire between the

heart rate board and the display mount.

1

STEP 3.

Disconnect the 12-pin serial cable and the

heart rate cable from the display.

2

3

11

620-7991 Rev 002

STEP 4.

Remove the cap cover with the Star Trac logo

from the back cover plastics by removing the (2)

screws using a #2 Phillips screwdriver. Retain

the screws for later use.

You will no longer need the cap cover and, if desired,

you can store it away for any possible future use.

STEP 5.

Remove the (2) M8 buttonhead screws retaining

the cross-brace using provided 5mm Hex key.

Retain screws for later use.

You will no longer need the cross-brace and, if de-

sired, you can store it away for any possible future

use.

STEP 6.

It is now time to install the Personal Viewing

Screen. Remove the PVS with its mounting

bracket and cables from the packaging. Also re-

move the (2) M8 buttonhead screws from the

hardware kit in the packaging.

You can use the foam bag that ships inside the Personal Viewing Screen package to

place the display face onto. This will help protect it from being damaged.

12

620-7991 Rev 002

STEP 8.

Adjust the cap with the grommet into place. Using

the 5mm Hex key, tighten the M8 buttonhead

screws to 190 lb-in (21.5 N-m) of torque. Take

the (2) Phillips head screws you removed from

the original cap and snugly tighten screws down

using a #2 Phillips screwdriver.

Check the back side of the display to see that the cap is seated properly. If not, loosen

the two Phillips Head Screws, adjust the cap and then retighten the screws.

STEP 9.

Using a #2 Phillips head screwdriver, remove

the (4) screws that hold bottom side of the dis-

play console on. Next remove the bottom cover.

Caution: When removing bottom cover, gently

disconnect the CSAFE cable from the back of

the display board.

Retain screws for later use.

STEP 7.

Mount the PVS assembly on the mounting

bracket, then thread the (4) M8 buttonhead

screws through the PVS mounting bracket into

the display mount. Do not tighten the screws yet.

Note:

(2) of the screws are in the PVS kit, (2) retained from

step 5.

13

620-7991 Rev 002

STEP 12.

insert the new center console into the front dis-

play. Using a #2 Phillips screwdriver, screw in

the (4) screws that were saved from the original

center console. Tighten the screws so they are

snug.

STEP 10.

Using a #2 Phillips head screwdriver, remove

the (4) screws that hold center console to the

display and remove the screw that holds in the

blank cover where the new headphone jack

mount will go.

Next detach the center console ribbon cable

then remove the center console and the blank

headphone cover. Retain screws for later

use.

Note: You will no longer need the center console

and headphone jack cover, both can be stored away

for any possible future use.

STEP 11.

Take the new PVS center console from the kit.

14

620-7991 Rev 002

STEP 13.

Note: If the iPod cable comes pre-installed on the cradle,

skip this step.

Take the iPod® cable from the kit. Install the

cable into the iPod® cradle on the front side of

the display console by removing the plug from

the cradle then inserting the cable through open-

ing. Make sure cable is aligned properly with the

display plastics. Press firmly to ensure the cable

is seated into the cradle.

STEP 14.

With the center console now installed, it is time

to attach the USB cable, center console ribbon

and the iPod® cable. Take the USB cable from

the center console and attach it to the CCB J14

connector on the display board. Next take the

center console ribbon cable and attach it to the

display PC board. Then take the iPod® cable

from the base of the mount to the center con-

sole. Tie the iPod® cable to the plastic using the

3.5” tie wrap.

STEP 15.

Next replace the bottom cover. Using a #2 Phil-

lips head screwdriver, replace the (4) screws

that hold the bottom side of the display console

on. Then plug in the CSAFE cable to the back of

the display board.

Make sure pin one on the cable is connected to pin one on the board.

15

620-7991 Rev 002

STEP 16.

Take the coax cable from the PVS mount and

attach it to the coax cable on the base unit.

Tighten the connectors snug to each other.

With the changes now completed on the display, it is now time to re-install the display console to the

base unit. There are the (3) cables from the PVS mount that will need to be attached to the display.

One cable from the PVS mount will be fed through the display which will be connected to the head

phone jack later. The fifth cable from the PVS mount, which is the coax, will be connected to the

coax on the base unit. There are (2) cables from the base unit that will be connected to the display.

Use the image below to help reference the needed points on the display.

STEP 17.

Now take the 5” silicon wrap from the kit and

peel off its protective tape then wrap the two

connectors so that all of the metal surface is

covered

STEP 18.

Using a 5” tie wrap from the PVS kit, bind the

cables from the PVS neck to one side of the

display mount. Take the tie and put it through

the hole on one of the display mount tubes.

STEP 19.

Now, take the front display plastics with the new

center console to the base unit. Hold the front

display plastics at the top with one hand while

connecting the cables/harnesses with the other.

There is no particular order in connecting the

cables. However, it may be best to start off con-

necting the cables/harnessing coming from the

neck of the base unit.

16

620-7991 Rev 002

STEP 20.

•

Connect the 12 pin serial cable from the base frame neck to the 12 pin socket on the dis-

play.

•

Connect the ground cable from the front display heart rate board to one of the terminals

on the display mount.

•

Connect the heart rate cable from the display support tube to the heart rate board on the

display.

•

Connect the DC power from the base frame neck to either one of the DC connectors on

the front display center console board.

•

Connect the DC power from the PVS display neck to the other DC connector on the front

display center console board

•

Connect the AV cables from the PVS display neck to the (2) AV connectors on the center

console board.

•

Connect the ground cable from the front display center console to one of the terminals

on the display mount.

1

3

4

2

5

6

17

620-7991 Rev 002

STEP 23.

Now that all the cables are in their places, and

confined to the post on the display mount, place

the display front plastic onto the back. Make

sure the bottom of the display front is under the

2 tabs on the display mount. Press the front dis-

play against the round tube and rotate it to the

back. Be careful not to pinch any wires.

STEP 21.

Feed the headphone jack cable from the PVS

display neck through the hole in the front dis-

play plastics where the blank cover was re-

moved earlier.

STEP 22.

Take the entertainment headphone jack from

the PVS kit and attach it to the cable that is

hanging out of the front of the display. Make

sure the connector is seated all the way into the

jack. Now slide the jack into the front of the dis-

play. Using a #2 Phillips screwdriver, fasten the

headphone jack into the front display with the

screw that was saved from the earlier step.

18

620-7991 Rev 002

STEP 24.

Using a #2 Phillips screwdriver, secure the front

display to the back with the (8) screws you pre-

viously removed and saved.

STEP 25.

Now with the Personal Viewing Screen installed

on your Star Trac equipment, it is time to con-

nect your entertainment cable and power to the

unit. Look at the bottom of the neck, next to the

floor. Connect your in-house Entertainment ca-

ble to the RF input. Take the power supply from

the PVS kit and plug the small barrel connector

to the DC input. Now take the appropriate

power adapter cable from the kit and plug it into

the power supply and the electrical receptacle.

Only use the power supply that was provided in your Personal Viewing Screen Kit. Us-

ing the wrong supply may damage your PVS.

This completes the installation of the Personal Viewing Screen on the E-UB / E-RB / E-TBT / E-ST.

Now it is time to set it up. Turn to the appropriate section for your Personal Viewing Screen.

19

620-7991 Rev 002

STEP 3. (E-TRx ONLY)

Note: If you have an E-TR skip this step.

Using a #2 Phillips screwdriver, remove the

screw that holds in the blank headphone jack

cap at the lower front of the Hot Bar. Retain the

screw.

You will no longer need the cap and, if desired, you

can store it away for any possible future use.

Now take the headphone jack from the iPod®

CC hardware kit. Connect the headphone jack

to the cable in the jack opening. Use the previ-

ously retained screw to reinstall the headphone

jack. Tighten snugly.

Skip ahead to Step 5.

STEP 1.

Using a #2 Phillips screwdriver, remove the (8)

screws from the upper back of the display.

Place the cover somewhere safe to keep it from

being damaged. Next, remove the (6) screws

from the lower back of the display. Place the

cover with the other one. Retain all the screws

for later use.

STEP 2.

Now remove the upper cap cover that has the

STAR TRAC logo on it. This cap is held in by

the upper back cover.

You will no longer need this cap cover and, if de-

sired, you can store it away for any possible future

use.

I

NSTALLING

Y

OUR PVS

O

N

T

HE

E

-TR

A

ND

E

-TRx

20

620-7991 Rev 002

STEP 6.

Take the Personal Viewing Screen from the

PVS kit. Next, take the (3) M8 buttonhead

screws, the M8 Hex nut with washer, and the

5mm Hex key from the PVS hardware tool kit.

Mount the Personal Viewing Screen on the

treadmill. Using the 5mm Hex key, screw in the

(2) M8 buttonheads at the base of the PVS first

(do not tighten yet). Using the 5mm hex key put

one of the M8 buttonhead screws into the hole

on the PVS neck, then put the Hex nut with

washer on the back side (do not tighten).

STEP 4. (E-TR ONLY)

Using a #2 Phillips screwdriver, remove the

screw that holds in the blank headphone jack

cap at the lower front of the display. Retain the

screw.

You will no longer need the cap and, if desired, you

can store it away for any possible future use.

Now take the headphone jack from the iPod®

CC hardware kit. Connect the headphone jack

to the cable in the jack opening. Use the previ-

ously retained screw to reinstall the headphone

jack. Tighten snugly.

STEP 5.

Detach the center console ribbon cable from the

display board by gently pulling on the ribbon

connector. Using a #2 Phillips screwdriver to

remove the (4) screws that hold the center con-

sole in place. Retain the screws for later use.

Remove the center console. You will no longer

need this center console and, if desired, you can

store it away for any possible future use.

STEP 7.

Adjust the display cap up or down to align with

the holes on the display front. Once the cap is

aligned, tighten all three buttonhead screws

with the 5mm hex key.

Page is loading ...

Star Trac E Series Upright E-UBi Gen. 1 User manual

Star Trac E Series Upright E-UBi Gen. 1 User manual

Related papers

Other documents