Newport TB & TBC Tie Bar User manual

Brand: Newport

Model: TB & TBC Tie Bar

Type: User manual

TB & TBC Series System

OPERATOR’S

MANUAL

Warranty

Newport Corporation warrants this product to be free of defects in material

and workmanship for a period of one year from the date of shipment. If found

to be defective during the warranty period, the product will either be repaired

or replaced at Newport’s option.

To exercise this warranty, write or call your local Newport representative or

contact Newport headquarters in Irvine, California. You will be given prompt

assistance and return instructions.

Repaired or replaced products are warranted for the balance of the original

warranty period or 90 days, whichever is longer.

This warranty does not apply to defects resulting from modifications or

improper use of the system or its component parts.

This warranty is in lieu of all other warranties, expressed or implied,

including any implied warranty of merchantability or fitness for a particular

use. Newport Corporation shall not be liable for any indirect, special, or

consequential damages.

Irvine, California, U.S.A.

P/N 19602, Rev. A

IN-04923 (08-00)

iii

Table of Contents

Warranty ............................................................................................................... ii

List of Figures ..................................................................................................... iii

Specifications ...................................................................................................... iv

Section 1 — General Information .................................................................... 1

1.1 Introduction ............................................................................................ 1

1.2 Getting Started ....................................................................................... 1

1.3 Unpacking and Inspection .................................................................... 1

1.4 Safety Considerations ........................................................................... 2

1.5 Warranty Information............................................................................ 2

Section 2 — Assembly ........................................................................................ 3

2.1 Preparing for Assembly ........................................................................ 3

2.2 Assembling During Table Installation ................................................. 3

2.3 Assembling After Table Installation .................................................... 5

Section 3 — Operation ....................................................................................... 7

3.1 Operation ................................................................................................ 7

3.2 Maintenance ........................................................................................... 7

3.2.1 Cleaning ......................................................................................... 7

3.2.2 Spare Parts .................................................................................... 7

Section 4 — Factory Service ............................................................................. 8

4.1 Obtaining Factory Service .................................................................... 8

4.2 Service Form ........................................................................................... 9

List of Figures

1.1 I-2000 Isolators with Model TBC Tie-Bars and Casters ..................2

2.1 Isolator Position ...................................................................................3

2.2 Installing Casters .................................................................................4

2.3 Assembling Tie-Bar to the Isolator .................................................... 5

2.4 Caster Assembly ..................................................................................6

Specifications

Load Capacity TBC-xx Series System

Standard Capacity

2800 lbs. (1271 kg.)

TBC-xx-HD Series System

Heavy Duty Capacity

5600 lbs. (2542 kg.)

TB-xx Series System

2000 lbs. (908 kg.) per

I-2000 Isolator in the System

Standard Sizes*

English Tables English Metric Tables Metric Price

(ft.) Model (m) Model

Tie-Bars and Casters

4 × 6 TBC-46 1.2 × 1.8 M-TBC-46 $619

4 × 8 TBC-48 1.2 × 2.4 M-TBC-48 $619

4 × 10 TBC-410 1.2 × 3.0 M-TBC-410 $619

4 × 12 TBC-412 1.2 × 3.6 M-TBC-412 $619

5 × 6 TBC-56 1.5 × 1.8 M-TBC-56 $619

5 × 8 TBC-58 1.5 × 2.4 M-TBC-58 $619

5 × 10 TBC-510 1.5 × 3.0 M-TBC-510 $619

5 × 12 TBC-512 1.5 × 3.6 M-TBC-512 $619

Tie-Bars only

4 × 6 TB-46 1.2 × 1.8 M-TB-46 $260

4 × 8 TB-48 1.2 × 2.4 M-TB-48 $260

4 × 10 TB-410 1.2 × 3.0 M-TB-410 $260

4 × 12 TB-412 1.2 × 3.6 M-TB-412 $260

5 × 6 TB-56 1.5 × 1.8 M-TB-56 $260

5 × 8 TB-58 1.5 × 2.4 M-TB-58 $260

5 × 10 TB-510 1.5 × 3.0 M-TB-510 $260

5 × 12 TB-512 1.5 × 3.6 M-TB-512 $260

* For other sizes, contact your local Newport Representative

Section 1

General Information

1.1 Introduction

The Newport TB Tie-Bar and TBC Tie-Bar with caster systems provide addi-

tional stability for table systems that use the Stabilizer series isolators. In

addition, the model TBC (with casters), provides a secure and safe method of

moving the table and isolators as a complete assembly, without the need for

forklifts or other specialized equipment.

The Newport TBC system is designed to alleviate stress in the table and

isolator system during relocation.

1.2 Getting Started

Please read this instruction manual thoroughly before assembling the Tie-Bar

Systems.

1.3 Unpacking and Inspection

The components of the Newport TB and TBC Tie-Bar Systems are packed in a

single box. Be sure the number of boxes you received is equal to the total

number listed on the label (for example, if a box is labeled 1 of 4, there should

be 4 boxes).

Use the diagram in Figure 1.1 to locate and identify each component as you

remove it from the box. Carefully inspect all components for shipping dam-

age. Report any shipping damage immediately to Newport and the shipping

company.

The Newport TB Tie-Bar System should be ordered with the table system, and

installed at the time of initial table installation. The TBC Casters may be

ordered as an accessory to be installed at a later date.

1.4 Safety Considerations

The following terms are used in this manual that relate to your safety.

Warning is used to indicate dangers that could result in personal injury.

Caution is used to indicate situations that may result in damage to components

of the Newport Table System.

1.5 Warranty Information

Warranty information may be found on the page preceding the Table of

Contents in this manual. Should it become necessary to exercise the war-

ranty, contact your Newport representative to determine the proper course of

action. Newport Corporation maintains offices throughout the United States

and other locations worldwide. Refer to the back cover of this manual for the

address and telephone number of the office nearest you.

.50-13 x 2.5 Hex Bolt

(4 Places)

I-2000

Isolator

.312-18 x 4.5 Hex Bolt

Flat Washer (2)

Lock Washer

Nut

(4 Places

8 Places on Heavy Duty)

.312-18 x .88 Hex Bolt

Flat Washer (2)

Lock Washer

Nut

(16 Places)

Caster Assy

(4 Places

8 Required for Heavy Duty System)

NOTE: See Spare Parts List

for Part Numbers

.312-18 x .88 Hex Bolt

Flat Washer

Lock Washer

(8 Places)

Tie Bar

(4 Places)

Figure 1.1 – I-2000 Isolators with Model TBC Tie-Bars and Casters.

Section 2

Assembly

2.1 Preparing For Assembly

The Newport Tie-Bar systems are fastened to the isolators of the Newport

Table System. If you are installing the caster kit on a previously assembled TB

system, skip to Section 2.3. If you are installing the Tie-Bars on a new table

system, proceed with Section 2.2.

2.2 Assembling During Table Installation

If you are installing a Newport Table system with Tie-Bars, use the following

procedure to assemble the TB Tie-Bar System.

A. Unpack the Table System components as described in the Newport

Vibration Control System Instruction Manual. Ensure that the isolators have

the attachment bars required for the Tie-Bars.

B. Remove the Tie-Bars, casters (if ordered), and hardware from the packing

cartons and place them on the floor near the table.

NOTE: Casters may be pre-installed in the isolator attachment bars.

C. Refer to Figure 2.1 for correct placement of the isolators.

D Typ.

B Typ.

6" (152 mm)

4 PL

Leveling Valve

Bracket

Caster Location

4 Places

Figure 2.1 Isolator Position

Table Distance Distance

Length A B

English Sizes: [in. (mm.)]

6' 40 (987) 16 (406)

8' 52 (1282) 22 (559)

10' 66 (1682) 27 (686)

12' 80 (1974) 32 (813)

14' 94 (2420) 37 (940)

16' 104 (2565) 42 (1087)

18' 120 (2962) 47 (1194)

20' 134 (3308) 53 (1346)

Metric Sizes: [mm.]

1500 839.6 330

1800 987.2 406

2000 1120.0 440

2100 1195.2 452

3000 1628.4 686

3600 1974.4 813

(Dimension D = Table Width - 12 in.)

D. Use the following procedure to install the casters. Casters must be

installed on the attachment bars marked with an X in Figure 2.1.

CAUTION:

Do not allow the isolator to tilt more than 60° from vertical. Damping

oil may spill from the isolator if it is tilted more than 60°.

1. Carefully tilt the first isolator so that the attachment bar is raised

approximately 1.5 inches. (Figure 2.2).

2. Slide the caster, with its pivot hole toward the isolator, under the

attachment bar. Ensure that the end of the caster mounting plate is

above the stop-bar as shown in Figure 2.2.

3. Return the isolator to its vertical position. Fasten the caster to the

attachment bar with a .312-18 x 4.5-inch pivot bolt, lock washer, and nut.

Use flat washers on both sides of the attachment bar (see Figure 2.3).

Align caster pivot hole with

holes in attachment bar.

Stop Bar

1.5"

Mounting Plate (above stop bar)

Figure 2.2 Installing Caster

4. Repeat steps 1 through 3 for the remaining isolators.

E. Place the four Tie-Bars over the attachment bars extending from the

isolators. Ensure that the bolt holes on the top and side of the Tie-Bars

are aligned with the holes in the attachment bars. (Figure 2.3).

F. Insert two .312-18 x .88-inch bolts with flat washers through the side holes

in the Tie-Bar. Fasten the bolts with flat washers, lockwashers, and hex

nuts inside the Tie-Bars. Do not tighten the bolts at this time.

G. Insert a .312-18 x .88-inch bolt with washers into the hole on top of the

Tie-Bar. Tighten the bolt hand-tight.

H. Ensure that the isolator spacing is as described in Figure 2.1.

I. When all four Tie-Bars have been installed, tighten all bolts securely.

J. If Casters were installed in step D, install a .50-13 x 2.5-inch Lifting Bolt in

the remaining hole at the top of each Tie-Bar. Thread the bolt into the

assembly until it stops against the caster plate. Apply a small amount of

oil or grease to the bolt for smoother operation.

Pivot Bolt

.312-18 x 4.5

.312-18 x .88" Bolt

(3 Places)

Tie Bar

Figure 2.3 Assembling Tie-Bar to the Isolator

J. Refer to the Vibration Control System Instruction Manual to continue

assembling the Table.

CAUTION

The isolators must be bolted to the table using the Safelok™ clamps pro-

vided with the isolators prior to lifting & moving the table on the casters.

2.3 Assembling After Table Installation

The following procedure is for installing the TBC Tie-Bar Casters to an existing

Table System. This procedure assumes that the Table System is assembled,

with the Tie-Bars and table top in place. Casters are installed in the attach-

ment bars marked with an X in Figure 2.1.

A. Turn off the air supply to the table and allow the table to settle before

proceeding.

B. Place a fork-lift or similar equipment under one of the longer Tie-Bars so

that the forks are no more than 12" (30 cm) from the isolators. Carefully

raise the table, isolators, and tie bar assembly approximately three inches.

WARNING:

The assembled table system may weigh in excess of 1000 pounds (454 kg).

Be sure the table is secured to the isolators using the Safelok™ clamps

provided with the isolators prior to lifting. Personal injury could result if

the table slips off of the forklift. Place blocks under the raised isolators

before working under the Tie-Bars

C. Refer to Figure 2.4. Slide one caster under each end of the Tie-Bar so that

the caster pivot hole is toward the isolator and the end of the caster

mounting plate is above the stop bar.

D. Fasten the casters to the attachment bars with the .312-18 x 4.5-inch pivot

bolts and hex nuts. Be sure to install the flat washers on each side of the

assembly.

E. Tighten the bolts to secure the casters and lower the table assembly until

the isolators are resting on the floor.

F. Insert the .50-13 x 2.5-inch bolt through the top of the Tie-Bar at each end.

Thread the bolts into the Tie-Bar until they stop on the caster plate.

Apply a small amount of oil or grease to the bolt for smoother operation.

G. Repeat steps B through F for the Tie-Bar on the opposite side of the table.

.312-18x4.5 Pivot Bolt

.5-13x2.5 Bolt

Stop Bar

Approx. 3"

Figure 2.4 Caster Assembly

H. Level and float the table as described in the Vibration Control System

Instruction Manual.

CAUTION

The isolators must be bolted to the table using the Safelok™ clamps pro-

vided with the isolators prior to lifting & moving the table on the casters.

Section 3

Operation

3.1 Operation

The Newport TBC Caster and Tie-Bar System provides a safe and stable

method for moving an assembled Table System without the need for disas-

sembling the table. To move the table after assembly:

A. Turn off the air supply and allow the table top to settle.

B. Ensure that the isolators are bolted to the table using the Safelok™ clamps.

C. Use a wrench to turn the four caster Lift Bolts clockwise (CW) into the

Tie-Bars, raising the isolators off the floor.

D. Carefully roll the table to its new location.

WARNING:

There are no brakes on the casters. To prevent injury or damage do not

roll the table up or down ramps.

E. After relocating the table, turn the caster Lift Bolts counter-clockwise

(CCW) until the isolators are resting on the floor.

F. Connect the air supply and refloat the table.

3.2 Maintenance

Newport TB and TBC systems require little maintenance. No periodic mainte-

nance is required.

3.2.1 Cleaning

Newport Tie-Bars are made of painted carbon steel. They may be cleaned by

applying non-abrasive liquid household cleaner to a rag and wiping the

surface dry. Avoid abrasive cleaners as they will scratch the surface.

3.2.2 Spare Parts

Part Name Part No.

Caster Assy 17847

Kit, Caster Mounting 17853

Kit, Tie Bar Mounting Hardware 17855

Instruction Manual 19602

Tie Bar 17574

Consult Newport for proper length.

Section 4

Factory Service

4.1 Obtaining Factory Service

To obtain information concerning factory service, contact Newport Corpora-

tion or your Newport representative. Please have the following information

available.

1. Model number.

2. Purchase order number.

3. Complete description of the problem.

If components are to be returned to Newport Corporation, you will be given a

Return Authorization Number, which you should reference in your shipping

documents.

Please fill out the service form located on the next page, and have the informa-

tion ready when contacting Newport Corporation. Include the completed

service form with any parts or components that are returned.

Comments or Suggestions

This manual was prepared with the help of several of Newport’s customers.

We gratefully acknowledge their assistance.

We would appreciate any comments or suggestions you may have to improve

this manual. Please call us at (714) 863-3144.

Name _____________________________________________________________________________________ RETURN AUTHORIZATION # ____________________________

Company _______________________________________________________________________________ (Please obtain prior to return of item)

Address _________________________________________________________________________________

Country _________________________________________________________________________________ Date _______________________________________________________________

P.O. Number __________________________________________________________________________ Phone Number ________________________________________________

Item(s) Being Returned:

Model # ________________________________________________________ Serial # __________________________________________________________________________________________

Description: _________________________________________________________________________________________________________________________________________________________

Reason for return of goods (please list any specific problems) ______________________________________________________________________________

____________________________________________________________________________________________________________________________________________________________________________

Please Describe the Problem:

____________________________________________________________________________________________________________________________________________________________________________

_______________________________________________________________________________________________________________ (Attach additional sheets as necessary).

Where is the Equipment Installed?

(factory, controlled laboratory, out-of-doors, etc.) _______________________________________________________________________________________________

Maximum Air Pressure Available? ______________________________________ Regulated? _____________________________________

Any additional information. (If special modifications have been made by the user, please describe below).

___________________________________________________________________________________________________________________________________________________________________________

Newport Corporation

U.S.A. Office: 949/863-3144

FAX: 949/253-1800

Service Form