IMC Networks IE-MiniFiberLinX-II,TP-TX/SSFX-SM1550/LONG-SC User manual

Brand: IMC Networks

Model: IE-MiniFiberLinX-II,TP-TX/SSFX-SM1550/LONG-SC

Category: Network media converters

Type: User manual

This manual is also suitable for

800-624-1070

www.imcnetworks.com

Features

• Smallest Standalone Fiber Optic Network

Interface Device

• VLAN Compatible - secure and separate

customer traffic

• Supports passive 802.3ah OAM (Operation,

Administration & Management)

• Extra Tagging (Q-in-Q)

• Supports Remote Loopback with MAC

Address Swap

Management

• Carrier-grade SNMP management and line

provisioning

• Link loss and loopback troubleshooting

• Free iView² EMS allows remote bandwidth

management and traffic prioritization

“Industrial Equipment” (IE) features for

operation in difficult environments

• Extended temperature functionality,

up to -20° to +75° C

• Multiple power options: AC, DC and

802.3af Power over Ethernet

• DIN clips for DIN-R ail mounting

Quality product

• Made in America with a comprehensive

six-year warranty

Transparent LAN service providers require remote management

capabilities, and must be able to isolate management traffic and

customer data. Typical Customer Premises Equipment (CPE)

do not allow this, since those devices are usually owned by

the customer and inaccessible to the network operator. The

compact IE-MiniFiberLinX-II, functioning as a more advanced

Network Interface Device (NID), is designed for operation

by service providers and campus network administrators. It

provisions point-to-point fiber optic connections and provides

a remote network interface at the customer’s location that

monitors the entire link between two locations.

The IE-MiniFiberLinX-II for fiber optic networks allows service

providers to deliver managed, high-bandwidth “triple play”

voice, video and data services to customer premises.

The IE-MiniFiberLinX-II and the fiber link can be managed as

a single entity, allowing remote configuration and autonomous

alerts to network administrators on fault conditions. As a copper-

to-fiber media converter, it allows low-cost copper switches to

connect to the fiber line. Offering unparalleled flexibility, the

IE-MiniFiberLinX-II supports multiple fiber types including multi-

mode and single-mode as well as single-strand fiber, doubling

the capacity of installed fiber. Coarse Wavelength Division

Multiplexing (CWDM) functionality is also an option.

The IE-MiniFiberLinX-II comes equipped with one 100 Mbps

fiber port for data and management, one 10/100 twisted pair

port for customer data, as well as an RS-232 port for local

configuration on the unit during installation.

The IE-MiniFiberLinX-II supports multiple powering options. Use

the included AC power adapter or use a 4-terminal DC power

block, which has an extended voltage range of 5 to 50VDC. The

IE-MiniFiberLinX-II also complies with the IEEE 802.3af Power

over Ethernet standard, acting as a Powered Device (PD) to draw

power when connected to 802.3af-compliant Power Sourcing

Equipment (PSE).

Combining copper-to-fiber conversion, extended

temperature performance, plug-and-play

operation, miniature size and multiple power

options, the IE-MiniFiberLinX-II is one of the

most versatile fiber optic NID devices available

on the market today.

IE-MiniFiberLinX-II

www.imcnetworks.com 800-624-1070

SNMP-Manageable Optical Ethernet Demarcation Unit For 10/100 Mbps Ethernet

Compact Fiber Optic Network Interface Device

for Industrial-Grade Delivery of Transparent

LAN Services over Fiber, with Media Conversion,

Carrier Grade Remote Management and Line

Provisioning Capabilities.

NID Application

Typical Application—

Service Provider

RoHS Compliant

www.imcnetworks.com 800-624-1070

Full-Featured IE-MiniFiberLinX-II

• VLAN Support— VLAN tagging capability keeps customer

data and SNMP traffic separated

• Troubleshooting Features— FiberAlert, LinkLoss and 802.3ah

Passive OAM (Operations, Administration and Maintenance)

assist in diagnosing potential problems on fiber optic networks

• Loopback Testing— Functionality loops back all frames

arriving on the fiber port (except for the device’s management

traffic). Supports MAC Address swap on Loopbacks

• Bandwidth Control— Fine granularity allows operators to

offer custom levels of service and easily change bandwidth

allocation, remotely, in seconds via SNMP

• Supports the Unified Management Agent (UMA)—

The FiberLinX family has always supported Host/Remote

environments, i.e. managing the Remote from the Host

location. With UMA, operators can centrally manage all

devices installed in an iMediaChassis using only a single IP

address for the chassis. Refer to the UMA data sheet for more

information

• IEEE 802.1Q VLAN compatible

• Valid VLAN IDs are 1 to 4,094

• Port-based VLAN tagging and Q-in-Q (extra tagging)

• Transparency Mode passes all data and respects the VLAN tag or

lack thereof, i.e. allows a mixture of VLAN Tagged and Untagged

traffic

• Configure to support VLAN IDs, filtering/passing up to 32 VLAN IDs

for data, plus an additional VLAN ID for SNMP management

• IEEE 802.1p provides a two-tier queue for differential prioritization

of inbound and outbound traffic, which is especially beneficial for

traffic requiring high priority, such as VoIP

Service providers routinely use IEEE 802.1Q Virtual Local Area Network (VLAN) tagging to secure, separate and differentiate customer traffic. The

IE-MiniFiberLinX-II enables service providers support of multiple VLAN-based applications.

From a central location, network operators are able to receive real-time device and traffic statistics on the remote device, allocate bandwidth, turn

services on or off, initiate loopback testing, modify VLAN settings and adjust QoS policies assigned to different traffic types.

Using the VLAN Functionality on the IE-MiniFiberLinX-II

• Scalability allows transport of data on up to eight wavelengths • Increase bandwidth without the addition of more fiber strands

Optionally, the IE-MiniFiberLinX-II provide for Coarse Wave Division Multiplexing, adding scalability to data delivery

Using Coarse Wavelength Division Multiplexing (CWDM) with the IE-MiniFiberLinX-II

SNMP Management Made Easy

The IE-MiniFiberLinX-II features an SNMP management

agent for monitoring the status and activity on copper

and fiber ports at the remote end. Initial setup and

modifications can be performed in the field via iView²

SNMP application, Telnet/TFTP, or a local serial (CRAFT)

connection.

• Remote, software upgrades via Telnet/TFTP or

management software ( iView²)

• Monitor unit and fiber with real-time monitoring and

statistics

• Change bandwidth “on-the-fly” up to 100 Mbps

• Create a secure management domain to isolate

management domain broadcasts from TX Data ports

on both units

• User-definable unit/port descriptions and information

www.imcnetworks.com 800-624-1070

General

• Preserves complete end-to-end fiber

connection integrity

• Bi-directional bandwidth control

• Read/write IEEE 802.1Q VLAN-tags

• Supports Extra Tagging (Q-in-Q)

• Supports passive 802.3ah OAM

(Operation, Administration &

Management)

• QoS: IEEE 802.1p-based packet

prioritization (2 queues [high/low] with

8 levels of priority)

• Layer 2 packet switching, store and

forward operation

• Forwarding rate: 14,881 pps for 10 Mbps;

148,810 pps for 100 Mbps

• AutoCross for MDI/MDIX

• Features Auto Negotiation and Selective

Advertising

• Supports Half and Full-Duplex operation

• MTU: Supports over-sized packets up to

1916 bytes per packet

Security

• Password Control

• Multiple Access Levels: User Assigned

Accounts & Access Levels

Management

• SNMP V1 and V2c compatible

• Includes GUI-based iView² software for

remote management and upgrades

• Monitors far-end (remote) status without a

physical presence or separate connection

• IEEE 802.3x Flow Control

• Includes DHCP and TFTP clients

• Supports Telnet

• Includes loopback test modes

(MAC swap)

• Includes LinkLoss and FiberAlert

• Supports the Unified Management Agent

(UMA)

• Includes status LEDs

• RS-232 (Craft) interface for local

management

• Serial cable for direct connection to a

PC’s Serial Port

Ethernet Types Supported

• IEEE 802.3i 10Base-T twisted pair

• IEEE 802.3u 100Base-TX twisted pair

• IEEE 802.3u 100Base-FX or SX fiber

Technical Specifications

Network operators can deploy a single

IE-MiniFiberLinX-II in stand-alone applications. At

the Central Office (CO), a fiber switch connects

via a fiber cable to the IE-MiniFiberLinX-II at the

customer premises. The IE-MiniFiberLinX-II can be

managed from the CO over SNMP or Telnet.

The IE-MiniFiberLinX-II is very versatile and offers

a range of AC and DC powering options. It

also supports 802.3af powering functionality,

allowing it to act as a Powered Device (PD).

The IE-MiniFiberLinX-II can be powered from a

PSE-enabled wireless Access Point, which in turn

can be powered by a remote source such as

the solar panels on a street light. The data is

transmitted over fiber to an iMediaChassis/20 with

iMcV modules in the Central Office to form an

end-to-end managed system.

Typical Application— Single

IE-MiniFiberLinX-II Solution

Application Examples (cont.)

Typical Application— Powering

Options

NID Application

Networking

RoHS Compliant

Fiber Types Supported

• 50/125µm or 62.5/125µm multi-mode fiber

• 9/125µm single-mode fiber

• Single-strand fiber or CWDM

Connectors: RJ-45, and ST or SC

Shipping Weight: 0.30 lbs (0.11 kg)

Dimensions: 0.83”H x 1.80”W x 3.35”D

(2.11 x 4.57 x 8.51 cm)

Environmental

• Humidity: 5% - 95% (non-condensing)

• Operating Temperature: -4° to +167° F

(-20° to +75° C) excluding AC wall adapter;

with AC wall adapter:

+32° to +122° F (0° to +50°C)

• Storage Temperature:

-49° to +185° F (-45° to +85° C)

Power

• DC Input Voltage:

750mA @ 5V to 75mA @ 50 VDC

• IEEE 802.3af Power over Ethernet

Physical Specifications

DS-IE-Mini-FiberLinx-II-1005

reserved. The information in this document is

subject to change without notice. IMC Networks

assumes no responsibility for any errors that may

appear in this document. Specific product names

may be trademarks or registered trademarks and

are the property of their respective companies.

IMC Networks

Fiber Consulting Services

For information call:

TEL: 949-465-3000

1-800-624-1070

(US/CAN)

+32-16-550880 (Europe)

[email protected]

IMC Networks

Headquarters

19772 Pauling

Foothill Ranch, CA 92610

TEL: 949-465-3000

FAX: 949-465-3020

[email protected]

IMC Networks

Europe

Herseltsesteenweg 268

B-3200 Aarschot, Belgium

TEL: +32-16-550880

FAX: +32-16-550888

[email protected]

IMC Networks

Eastern US/Latin America

28050 U.S. Hwy. 19 North, Suite 306

Clearwater, FL 33761

TEL: 727-797-0300

FAX: 727-797-0331

[email protected]

IMC MIB:

·Traps (Cold Start, Warm Start,

Authentication Failure, Link Up, Link

Down, Remote Unit Lost, Remote

Unit Back Online, Far End TX Link

On and Far End TX Link Off)*

· Link Status of Ports

· Port Type

· Fiber Type

· SNMP Port (Host/Remote)

· SNMP Agent IP Address

(Host/Remote/Single)

· Link Partner

· User-Definable Name of Product

· User-Definable ID/Name of Ports

· Enable/Disable Ports

· Enable/Disable FiberAlert

· Enable/Disable loopback modes

· Set Duplex Mode for Twisted

Pair Ports

· Set Auto Negotiation/Speed for

Twisted Pair Ports

MIB-II (RFC 1213):

· Packets Transmitted

· Packets Received

· Octets (bytes) Transmitted

· Octets (bytes) Received

· Plus All Standard MIB II Objects

RMON Statistics provided for:

· Drop Events

· Total Bytes

· Total Packets

· Broadcast Packets

· Multicast Packets

· CRC Align Errors

· Undersize Packets

· Oversize Packets

· Fragments

· Jabbers

· Collisions

· Distribution of Frame Size

*Send traps to a virtually unlimited number of trap-host server destinations.

Ordering Information

Technical Specifications (con’t.)

PART NUMBER

W/ AC ADAPTER

PART NUMBER

W/O AC ADAPTER

DESCRIPTION DISTANCE

IE-MiniFiberLinX-II TP-TX/FX (Industrial Ethernet)

856-19717 856-19740 IE-MiniFiberLinX-II, TP-TX/FX-MM850-ST 2 km

856-19718 856-19741 IE-MiniFiberLinX-II, TP-TX/FX-MM850-SC 2 km

856-19722 856-19732 IE-MiniFiberLinX-II, TP-TX/FX-MM1300-ST 5 km

856-19723 856-19733 IE-MiniFiberLinX-II, TP-TX/FX-MM1300-SC 5 km

856-19724 856-19734

IE-MiniFiberLinX-II, TP-TX/FX-SM1310/PLUS-ST 40 km

856-19725 856-19735 IE-MiniFiberLinX-II, TP-TX/FX-SM1310/PLUS-SC 40 km

856-19726 856-19736 IE-MiniFiberLinX-II, TP-TX/FX-SM1310/LONG-ST 40 km

856-19727 856-19737 IE-MiniFiberLinX-II, TP-TX/FX-SM1310/LONG-SC 40 km

856-19730 - IE-MiniFiberLinX-II, TP-TX/FX-SM1550/LONG-SC 80 km

856-19728 - IE-MiniFiberLinX-II, TP-TX/FX-SM1550/XLONG-SC 100 km

IE-MiniFiberLinX-II TP-TX/SSFX Single-Strand Fiber* (Industrial Ethernet)

856-19750 856-19760 IE-MiniFiberLinX-II, TP-TX/SSFX-MM1300-SC (1550rcv) 2 km

856-19751 856-19761 IE-MiniFiberLinX-II, TP-TX/SSFX-MM1550-SC (1310rcv) 2 km

856-19752 856-19762 IE-MiniFiberLinX-II, TP-TX/SSFX-SM1310-SC (1550rcv) 20 km

856-19753 856-19763 IE-MiniFiberLinX-II, TP-TX/SSFX-SM1550-SC (1310rcv) 20 km

856-19754 856-19764 IE-MiniFiberLinX-II, TP-TX/SSFX-SM1310/PLUS-SC (1550rcv) 40 km

856-19755 856-19765 IE-MiniFiberLinX-II, TP-TX/SSFX-SM1550/PLUS-SC (1310rcv) 40 km

856-19756 856-19766 IE-MiniFiberLinX-II, TP-TX/SSFX-SM1310/LONG-SC (1550rcv) 60 km

856-19757 856-19767 IE-MiniFiberLinX-II, TP-TX/SSFX-SM1550/LONG-SC (1310rcv) 60 km

* These products have single-strand fiber technology. Deploy in pairs, or connect to another compatible IMC Networks single-strand fiber product.

For more information go to: www.imcnetworks.com/products/SSFX.cfm

IMC Networks IE-MiniFiberLinX-II,TP-TX/SSFX-SM1550/LONG-SC User manual

Brand: IMC Networks

Model: IE-MiniFiberLinX-II,TP-TX/SSFX-SM1550/LONG-SC

Category: Network media converters

Type: User manual

This manual is also suitable for

Download PDF

report

IMC Networks IE-MiniFiberLinX-II,TP-TX/SSFX-SM1550/LONG-SC User manual

This manual is also suitable for

IMC Networks IE-MiniFiberLinX-II,TP-TX/SSFX-SM1550/LONG-SC User manual

Related papers

Other documents