Datamax ICLASS Series Installation Instructions Manual

Type
Installation Instructions Manual
92-2191-01 Rev.D
Internal Rewind
Installation Instructions
Datamax International
Herbert House
12 Elizabeth Way, Pinnacles
Harlow, Essex CM19 5FE UK
Phone: +44 1279 772200
Fax: +44 1279 424448
Asia-Pacific
19 Loyang Way
#01-01 CILC Building
Singapore 508724
Phone: +65 542-2611
Fax: +65 542-3611
Corporate Headquarters
4501 Parkway Commerce Blvd.
Orlando, Fl 32808
Phone: 407-578-8007
Fax: 407-578-8377
Printed U.S.A. © Copyright 2002
1
Contents of the Internal Rewind Kit (78-2302-01)
This kit contains the following items:
Internal Rewind Assembly, p/n 15-2773-01
Rewind Bracket, p/n 11-5220-01
Thumbscrew, p/n 17-2858-01
Media Clip, p/n 11-5339-01
Rewinder Media Retainer, p/n 15-2864-01
(3) Screws, p/n 10-2903-04
Tools Required
The Internal Rewind Option only requires a #2 Phillips head screwdriver for installation.
Preparing the Printer
Turn the power off and unplug the printer.
Remove any installed media from the printer.
Open the cover and remove the Screws and
the Rewind Cover Plate.
2
Installing the Internal Rewind Assembly
Position the Internal Rewind Assembly in the
printer as shown and secure using the three
provided Screws.
Setup and Configuration
Remove the Front Fascia. Loosen and
remove the Thumbscrew and remove the
Tear Plate.
Position the Rewind Plate on the Printer and
install and tighten the Thumbscrew.
3
Loading Media
Route the media back to and around the Rewind Hub.
Insert the media’s leading edge into a Slot on the Media Rewind Hub then insert the Media Clip into
a Slot to secure.
Slide the Rewind Retainer onto the Media Rewind Hub to rest lightly against the outside edge of the
media and tighten the Thumbscrew to secure. Manually rotate the hub to remove any slack in the
media.
After finishing, close the Access Cover then push and hold the FEED key for 4 seconds to secure the backing
material and calibrate the TOF.
4
Internal Rewind: Parts List and Exploded View
ITEM # PART # DESCRIPTION
1 15-2773-01 MEDIA TAKE-UP ASSY
2 10-2903-04 SCREW TRILOBULAR M4 PHILIPS HEAD 10
3 17-2858-01 THUMBSCREW
4 11-5220-01 REWIND BRACKET
5 11-5339-01 RETAINER, MEDIA (Metal)
6 15-2864-01 RETAINER, MEDIA (Plastic)
7 12-2941-01 COVER, MEDIA TAKE-UP
8 15-2764-01 HUB ASSY, TAKE-UP
9 17-2310-01 BEARING, FLANGED .375 ID X .875 OD
10 17-2860-01 GEAR SPUR DELRIN, 24 TEETH
11 12-2905-01 POST IDLER
12 10-2903-06 SCREW TRILOBULAR M4 PHILIPS HEAD 25
13 10-0563-01 E-RING 3/8 TRUARC 5133-37
14 15-2802-01 CLUTCH ASSY, MEDIA
15 12-2925-01 HOUSING, SPOOL
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Datamax ICLASS Series Installation Instructions Manual

Type
Installation Instructions Manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI