Init NT-WGM1150 Assembly Instructions Manual

Brand: Init

Model: NT-WGM1150

Type: Assembly Instructions Manual

ASSEMBLY

INSTRUCTIONS

NT-WGM1150

50" 3-in-1 TV Stand with

Integrated Mount

Safety information and specifications ..................... 2

Tools needed..................................................................... 4

Parts...................................................................................... 5

Hardware ............................................................................ 6

Assembly instructions.................................................... 8

Finishing the table top assembly.........................13

Finishing the swivel mount assembly ................14

Finishing the wall-mount assembly....................22

Still need help? Call 800-573-2860

Safety information and specifications

CAUTION: This stand’s glass work

surface is intended only for use with a

product not weighing more than 100 lbs.

(45.5 kg) and having a width that will

permit it to sit evenly on the stand with no more

than a one-inch overhang on each side on the top

shelf. Using with other products, including

products that weigh more than the maximum

weight allowed or extend beyond the maximum

width, may result in instability, which may cause

possible injury.

Caution: This product contains small items that

could be a choking hazard if swallowed.

Keep these items away from young children!

Do not lift the glass by the support posts. See

instructions for more details.

Model #: NT-WGM1150

Distributed by Best Buy Purchasing, LLC

Manufacturer: Alart, Inc.

Manufacture Date:

Maximum weight: 100 lbs. (45.5 kg)

Maximum width: 1-inch overhang on each side of

the top shelf

Top shelf (W × D):

50 × 19" (127 × 48.26 cm)

Middle shelf (W × H × D):

44.25 × 9.5 × 15.5" (112.39 × 24.13 × 39.37 cm)

Bottom shelf (W × H × D):

44.25 × 10.13 × 18.13" (112.39 × 25.73 × 46.05 cm)

Still need help? Call 800-573-2860

19" (48.26 cm)

53" (134.62 cm)

50" (127 cm)

30"(76.2 cm)

17" (43.18 cm)

Still need help? Call 800-573-2860

Tools needed

(For optional TV wall mounting)

Drill

Phillips screwdriver

Stud finder

Level

Hammer

Drill bit for

stud wall

3/8" drill bit

for concrete

wall

Pencil

Still need help? Call 800-573-2860

Part s

Package contents: parts

A Stand body (1) B Top frame (1) C Bottom frame (1)

D Top shelf frame-wood(1)

E Top shelf-glass(1)

F Middle shelf-glass (1)

G Bottom shelf-glass(1)

P Tilt mount (1)N Vertical support (1) R TV bracket (2)

Still need help? Call 800-573-2860

Hardwa re

Package contents: stand hardware

Note: You may receive extra hardware.

Make sure you have all the hardware necessary to assemble your new TV stand:

Label Hardware Qty.

Small

thumbscrew

Medium

thumbscrew

Large

thumbscrew

Long

thumbscrew

Shelf support

An optional anti-tipping hardware kit is included.

Instructions on how to install the hardware are

included on the bag containing the kit.

Label Hardware Qty.

Shelf lock

Pivot plug

TV mount

bracket

For Steel

Touch-up pen

for steel

For Wood

Touch-up pen

for wood

1 0 20 30 40 50 60 70 80 90 100mm

1234in

Still need help? Call 800-573-2860

Wall-mount hardware

Package contents: wall-mount hardware

Note: You may receive extra hardware.

Make sure you have all the hardware necessary to assemble your new TV stand:

Label Hardware Qty.

Safety bolt (2)

M4 × 12 m

bolt

M4 × 16 mm

bolt

M5 × 16 mm

bolt

M6 × 16 mm

bolt

M8 × 16 mm

bolt

M5 × 36 mm

bolt

Label Hardware Qty.

M6 × 36 mm

bolt

M8 × 36 mm

bolt

Square

washer

Long bolt

Wall anchor

Long bolt

washer

Spacer

Still need help? Call 800-573-2860

Assembly instruct ions

Step 1 Unfold the stand body (A), then insert the shelf supports (L) into the side frames.

You’ll need:

L (2)

Still need help? Call 800-573-2860

Step 2 Attach the top frame (B), then secure it into place with two large thumbscrews (J).

Note: Make sure the front of top frame (B) engages with the side supports on the stand body.

You’ll need:

J (2)

Still need help? Call 800-573-2860

Step 3 Attach the bottom frame (C), then secure it into place with two large thumbscrews (J).

Note: Make sure the front of bottom frame (C) engages with the side supports on the stand body.

You’ll need:

J (2)

Still need help? Call 800-573-2860

Step 4 Attach the top shelf frame (D) with two small thumbscrews (H).

• For Table Top and Wall Mount assembly, continue to next step.

• For Swivel Stand assembly, continue to page 14.

You’ll need:

H (2)

Still need help? Call 800-573-2860

Step 5 Secure the top shelf (E) to the shelf frame (D) with four medium thumbscrews (I), then secure the middle

and bottom glass shelves (F and G) with a shelf lock (M).

• For final Table Top assembly, continue to the next step.

• For Wall Mount installation, continue to page 18.

You’ll need:

I (4)

M (1)

Still need help? Call 800-573-2860

Finishing the table top assembly

Step 1

Optional: Install the anti-tipping hardware. Instructions are included on the bag containing the hardware.

You need to remove the one of the top thumbscrews, place the loop on the tipping restraint over the thumbnail screw

hole, then replace the thumbscrew.

You’ll need:

Phillips screwdriver Drill

Still need help? Call 800-573-2860

Finishing the swivel mount assembly

Step 1

Attach the vertical support (N) by sliding the locking bolts at the bottom of the support into the holes on

the stand body, then pressing firmly downward to lock the vertical support into place.

Use long thumbscrews (K) to secure the vertical support (N) to the top of the stand frame.

Align the holes on the tilt mount (P) pivot bracket with the holes on the vertical support (N) pivot bracket, then insert

the pivot plug (Q) to lock the tilt mount (

P) in place. The pivot plug (Q) will insert easily when the two pieces are aligned

correctly.

You’ll need:

K (2)

Q (1)

Still need help? Call 800-573-2860

Step 2 Attach the TV mount brackets (R) to the back of the TV. Make sure that each TV mount bracket (R) is

oriented with the “UP” label on top.

If you TV has a flat back, go to page 16.

If you TV has a curves back or obstruction, go to page 17.

Still need help? Call 800-573-2860

Mounting instructions for a TV with a flat back:

Select the screws appropriate for your TV and use square washers (M) to attach the brackets to the back of your TV.

You’ll need:

M5, 6

, ,

E (4) F (4)

OR OR

H (4) I (4)

M (4) Phillips screwdriver

Still need help? Call 800-573-2860

Mounting instructions for a TV with a curved back or obstruction:

Select the screws appropriate for your TV. Use square washers (M) and spacers (R) to attach the brackets to the back of

your TV.

You’ll need:

M5, 6

, ,

J (4) K (4)

OR OR

L (4)

M (4) Phillips screwdriver

R (4)

Still need help? Call 800-573-2860

Step 3 Attach the TV mount brackets (R) to the tilt mount (P).

Lift the TV up to the tilt mount (P).

Warning: Use at least two people to mount the TV onto the tilt mount.

Set the hooks on the TV mounting brackets (R) over the tilt mount, then lower the hooks onto the bars of the tilt mount.

Still need help? Call 800-573-2860

Step 4 Center the TV and let the bottom of the TV rotate downward until it is against the vertical support. Insert

the safety bolts (D) to secure the TV in place.

You’ll need:

D (2)

Phillips screwdriver

Still need help? Call 800-573-2860

Step 5 To adjust the tilt angle, securely hold the top and bottom of the TV, then carefully pull the top of the TV

toward you or press it toward the vertical support (

N).

Page is loading ...

Init NT-WGM1150 Assembly Instructions Manual

Init NT-WGM1150 Assembly Instructions Manual

Init NT-WGM1150 Assembly Instructions Manual

Related papers

Other documents