1/5
By DGB Enterprises LLC
www.italiabath.com
Italia Bathroom Accessory Sets
Towel Bar
A
A
Towel Ring
B
B
Tools & Hardware
Toilet Paper Holder
C
C
Robe Hook
D
D
Hardware Included: A B C D
Allen Wrench 1x 1x 1x 1x
Plastic Wall Anchors 4x 2x 2x 2x
Mounting Screws 4x 2x 2x 2x
Mounting Bracket Plate
(Located pre-installed in item. Must
be removed prior to installation).
2x 1x 1x 1x
Set Screws
(Located pre-installed in item. Must be loosened
to remove the mounting plate prior to installation).
2x 1x 1x 1x
Installation & Care Guide
Phillips Screwdriver
Tools required:
Power Drill ¼” Drillbit
Tile / Masonry Stone Drillbit
if Drilling Into Tile or Stone
(Masonry wall anchors not included)
Hammer
Level Tape Measure Pencil
2/5
Use a soft cloth or sponge with water, then dry with a soft cloth. Avoid detergents, abrasive cleaners, solvents, steel and bronze wool.
Visit https://youtu.be/oyTQ2F-oOjI for an easy to follow installation video.
Contact [email protected] for questions or further information
Drill holes in using ¼” drillbit.
a. Mounting into wood studs is recommended;
b. If mounting into tile use a masonry stone drillbit.
Insert provided anchors if mounting into drywall. Anchors
not necessary if mounting into wood studs.
a. Optional: Use a dab of caulking on the wall anchors for
a better hold;
b. If drilling into tile use masonry wall anchors (not included).
Install the mounting plate with the provided screws.
a. The ange side should be facing out;
b. Optional: Use a dab of caulking on the back of each
mounting disc for a better hold.
Place towel bar over the mounting plates with the set
screw on the bottom.
Use the provided allen wrench to adjust the set screw to
lock into place with the mounting bracket.
4
5 6
7 8
Care Instructions
Place mounting plate on the wall and mark position of
the holes in the mounting plate.
3
Remove mounting plate(s) from back of item.
a. Use the provided allen wrench to loosen set screw on
bottom of the item to remove the mounting plate.
Level and mark position of the item on the wall.
a. If mounting into ceramic or tile, place masking tape on the
mounting areas before marking the location to prevent the
drill from slipping and damaging the tile.
Installation Instructions Towel Bar
1 2
3/5
Remove mounting plate from back of towel ring.
a. Use the provided allen wrench to loosen set screw on
bottom of the towel ring to remove the mounting plate.
Use a soft cloth or sponge with water, then dry with a soft cloth. Avoid detergents, abrasive cleaners, solvents, steel and bronze wool.
Visit https://youtu.be/oyTQ2F-oOjI for an easy to follow installation video.
Contact [email protected] for questions or further information
Drill holes in using ¼” drillbit.
a. Mounting into wood studs is recommended;
b. If mounting into tile use a masonry stone drillbit.
Insert provided anchors if mounting into drywall. Anchors
not necessary if mounting into wood studs.
a. Optional: Use a dab of caulking on the wall anchors for
a better hold;
b. If drilling into tile use masonry wall anchors (not included).
Install the mounting plate with the provided screws.
a. The ange side should be facing out;
b. Optional: Use a dab of caulking on the back of each
mounting disc for a better hold.
Place item over the mounting plates with the set screw
on the bottom.
Use the provided allen wrench to adjust the set screw to
lock into place with the mounting bracket.
4
5 6
7 8
Care Instructions
Place mounting plate on the wall and mark position of
the holes in the mounting plate.
3
Installation Instructions Towel Ring
1
Level and mark position of the towel ring on the wall.
a. If mounting into ceramic or tile, place masking tape on the
mounting areas before marking the location to prevent the
drill from slipping and damaging the tile.
2
4/5
Visit https://youtu.be/oyTQ2F-oOjI for an easy to follow installation video.
Contact [email protected] for questions or further information
Drill holes in using ¼” drillbit.
a. Mounting into wood studs is recommended;
b. If mounting into tile use a masonry stone drillbit.
Insert provided anchors if mounting into drywall. Anchors
not necessary if mounting into wood studs.
a. Optional: Use a dab of caulking on the wall anchors for
a better hold;
b. If drilling into tile use masonry wall anchors (not included).
Install the mounting plate with the provided screws.
a. The ange side should be facing out;
b. Optional: Use a dab of caulking on the back of each
mounting disc for a better hold.
4
5 6
8
Care Instructions
Place mounting plate on the wall and mark position of
the holes in the mounting plate.
3
Installation Instructions Toilet Paper Holder
2
1
Use the provided allen wrench to adjust the set screw to
lock into place with the mounting bracket.
Remove mounting plate from back of toilet paper holder.
a. Use the provided allen wrench to loosen set screw on bottom
of the toilet paper holder to remove the mounting plate.
Level and mark position of the toilet paper holder on the wall.
a. If mounting into ceramic or tile, place masking tape on the
mounting areas before marking the location to prevent the
drill from slipping and damaging the tile.
Place the toilet paper holder over the mounting plate
with the set screw on the bottom.
7
Use a soft cloth or sponge with water, then dry with a soft cloth. Avoid detergents, abrasive cleaners, solvents, steel and bronze wool.
2
5/5
2
Visit https://youtu.be/oyTQ2F-oOjI for an easy to follow installation video.
Contact [email protected] for questions or further information
Drill holes in using ¼” drillbit.
a. Mounting into wood studs is recommended;
b. If mounting into tile use a masonry stone drillbit.
Insert provided anchors if mounting into drywall. Anchors
not necessary if mounting into wood studs.
a. Optional: Use a dab of caulking on the wall anchors for
a better hold;
b. If drilling into tile use masonry wall anchors (not included).
Install the mounting plate with the provided screws.
a. The ange side should be facing out;
b. Optional: Use a dab of caulking on the back of each
mounting disc for a better hold.
4
5 6
8
Care Instructions
Place mounting plate on the wall and mark position of
the holes in the mounting plate.
3
Installation Instructions Robe Hook
Use the provided allen wrench to adjust the set screw to
lock into place with the mounting bracket.
Remove mounting plate from back of robe hook.
a. Use the provided allen wrench to loosen set screw on
bottom of the robe hook to remove the mounting plate.
Level and mark position of the robe hook on the wall.
a. If mounting into ceramic or tile, place masking tape on the
mounting areas before marking the location to prevent the
drill from slipping and damaging the tile.
1 2
Place the robe hook over the mounting plate with the set
screw on the bottom.
7
Use a soft cloth or sponge with water, then dry with a soft cloth. Avoid detergents, abrasive cleaners, solvents, steel and bronze wool.
-
1
-
2
-
3
-
4
-
5
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
MODONA 4H03-A Installation guide
-
MODONA 3H03-A Installation guide
-
Glacier Bay 391SSHD Installation guide
-
GATCO 1433 Installation guide
-
Dyconn BAHOOK-ORB User guide
-
Dyconn BA4SET24 Installation guide
-
CMI 182-6621 Installation guide
-
Dyconn Faucet BATPH-CHR Installation guide
-
-
BOANN BNAS4PK24 Installation guide
