SMD LED MINI LIGHT BAR 12/24V 50W -
MAGNETIC BASE, SINGLE POINT FIXING
MODEL NO: MLB80MB, MLB80SB
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
9 Familiariseyourselfwiththisproduct’sapplicationandlimitations,aswellasanyspecicpotentialhazardspeculiartothebeacon.
9 Replaceorrepairdamagedparts.Userecommendedpartsonly.Nonauthorisedpartsmaybedangerousandwillinvalidatethe
warranty.
8 DO NOTusethebeaconforanypurposeotherthanforwhichitisdesigned.
8 DO NOTallowchildrentooperatethebeacon.
8 DO NOToperatethebeaconifanypartsaremissingordamagedasthismaycausefailureorpossiblepersonalinjury.
9 Whennotinuseswitchthebeaconoandwhereappropriateremoveplugfrompowersupply.
2. INTRODUCTION
Extremelybright50WamberSMDLEDhighintensityminilightbarttedwithmagnetsonthebase.10Modulesttedwith8LEDs,creatinga
360°light.Fittedwitha3mcableand12Vvehicleaccessorysocket.Plugincludestwoswitches,on/oandamomentaryswitch,givingyouthe
optionof10dierentashpatterns.Built-inmemoryrecallslastpatternselected.ECER65andR10Approvedforhighwayuse.CEApproved
andE-Marked.IP66rated.Singleboltversionavailable(ModelNo.MLB80SB).
3. SPECIFICATION
Model No:............................................MLB80MB,MLB80SB
CurrentDrawinAmps:........................ (12V)2.5A/(24V)1.2A
Dimensions:.......................... (WxDxH)279x165x61mm
IPRating:........................................................................IP66
Power:.............................................................................50W
Supply:................................................................. 12-24VDC
Temperature Range:......................................-30°Cto+50°C
4. OPERATION
4.1. WIRING
4.1.1. Blackwireshouldbewiredtoasuitableearth.
4.1.2. Redwireshouldbewiredviaaswitchtoasuitablefused12V
livesupplyttedwitha5ampfuse.
4.1.3. Yellowwireshouldbewiredtoearthviaamomentary
switch(negativeearth).
4.2. ATTACHING THE LIGHT TO YOUR VEHICLE
4.2.1. Therearetwostrongmagnetsonthereverseoftheunit.
(g.1)
4.3. ATTACHING THE LIGHT BAR VIA THE SCREW FITTING
4.3.1. Thescrewcanberemovedfromtheundersideofthelight
barbyremovingthexingplate.(g.1)
4.3.2. Underthexingplatethereisarecessfortheheadof
thesetscrewtositin.Thiswillstopthesetscrewfrom
turningwhentighteningthenut.(g.2)
4.4. SWITCHING ON AND CHANGING THE LIGHT
PATTERN
4.4.1. Therearetwobuttonsontheincaradaptor.Oneswitch
(withLEDindicatorlight)switchesthelightonando.
The otherswitchswitcheslightpatterns.(g.3)
MLB80MB,MLB80SBIssue3(H23)02/05/23
Original Language Version
©JackSealeyLimited
Refer To
Instructions
g.1
g.2
Warning! Do Not
LookDirectlyInto
Light.
Warning!Hot
Surfaces