ZLINE MWDZ1BSHG is a sleek and functional microwave drawer that combines convenience and style. It features a spacious 1.2 cubic feet capacity, allowing you to easily heat or cook a variety of dishes. With 10 power levels and a variety of preset cooking options, you can customize your cooking to perfection. The microwave also includes a child lock feature for added safety.
ZLINE MWDZ1BSHG is a sleek and functional microwave drawer that combines convenience and style. It features a spacious 1.2 cubic feet capacity, allowing you to easily heat or cook a variety of dishes. With 10 power levels and a variety of preset cooking options, you can customize your cooking to perfection. The microwave also includes a child lock feature for added safety.
MICROWAVE DRAWER
TRIM KIT
www.zlinekitchen.com
Installation Manual
ZLINE Kitchen and Bath provides Attainable Luxury, where the kitchen and bath of your dreams
is never out of reach. Through our unique designs and unparalleled quality, we’re dedicated to
providing you an elevated experience in the heart of your home. With an endless selection of
features and finishes, our inspiration is your reality.
WARNING: This product can expose you to chemicals including nickel, which is known to the
State of California to cause cancer. For more information, go to www.P65Warnings.ca.gov.
ZLINE is fueled by a passion for innovation; A relentless pursuit of bringing the highest end luxury
designs and professional features into everyone’s homes. Because we continually strive to improve
our products, we may change specifications and designs without prior notice.
1
IMPORTANT SAFETY INFORMATION
Safety Information
NOTE: This trim kit is available for purchase as a separate accessory for ZLINE’s 24”
microwave drawer in stainless steel only. The trim kit is only available for the 24” unit;
it is not available in black stainless.
• Before installation and operation, please read and follow these important
instructions for the safety of your home and the people living in it.
• Disconnect your microwave from power while installing this trim kit.
• Use care when handling the outer trim, support beams and brackets, as sharp
edges may lead to injury. Use of gloves during installation is recommended.
• Save this installation manual for local electrical inspector’s use and for your own
future reference.
• Do not install this trim kit if it has missing or broken parts. If the kit arrives
damaged, contact ZLINE Customer Service at 1-614-777-5004 for help.
• When cleaning the stainless steel outer trim after installation, use only mild,
nonabrasive soaps or kitchen-safe cleaners applied with a sponge or soft cloth.
Do not clean with metal scouring pads.
2
Tools and Parts
BEFORE INSTALLATION
TOOLS NEEDED:
• Phillips-head screwdriver
• Marker
• Drill
PARTS INCLUDED:
PART QUANTITY IMAGE
Outer trim (1) 1
Support beam (2) 2
Front bracket (1) 1
Rear bracket (1) 1
Buckle seat (4) 4
Buckle (4) 4
Finishing washers (4) 4
#1 Screw (4) 4
#2 Screw (16) 16
#3 Screw (2) 2
3
Trim Kit Installation
1. Lay the support beams flat on the bottom of the cabinet cutout with the open
sides facing each other (see Figure 1).
Rear bracket
Front bracket
Rear bracket
Front bracket
Figure 1
To gauge proper width, temporarily place the rear and front brackets onto the
support beams so the rear bracket lips slide into rear holes on top of the beams
and the front screw holes match to the front of the beams (see Figure 2).
Figure 2
Once aligned, secure the beams by fastening the four #1 screws with washers
into the cabinet base below (see Figure 3).
Rear bracket
Front bracket
Rear bracket
Front bracket
Figure 3
INSTALLATION
4
INSTALLATION
Trim Kit Installation
2. Remove the screws from the front bottom of your microwave. Using two of those
screws, secure the front bracket to the bottom of the microwave, ensuring the lip
of the bracket is extending down and facing you. Next, remove the screws from
the back bottom of the microwave and fasten the rear bracket, ensuring the two
small lips are extended down and facing back (see Figures 4 and 5).
Rear bracket
Front bracket
Rear bracket
Front bracket
Rear bracket
Front bracket
Rear bracket
Front bracket
Figure 4 Figure 5
3. Lay the outer trim face down and, using eight of the #2 screws, install the four
buckles on the corresponding mounting holes around the trim kit (see Figure 6).
Make sure to use the same series of mounting holes on each corner, depending
on your cabinet cutout (see Figure 7).
① 将安装好卡扣的外观框放在橱柜上作出比对；用记号笔画上安
装位置
② 用1#螺丝将卡座安装在对应安装位置上
①
Use 2# screws to install the four buckles on the corresponding mounting
holes around the trim kit 使用 2#螺丝将四个卡扣安装在外观框四周对
应的安装孔上
Place the trim kit which install buckle on the cabinet for
contrast, then use marker strokes to draw the mounting
position
Figure 6 Figure 7
5
Trim Kit Installation
4. Next, slide the outer trim into the cabinet cutout and use a marker or pencil to
mark where the buckles line up. Then, remove the trim and secure the four buckle
seats into the cabinet using the other eight #2 screws (see Figure 8). Make sure
the clamp of the bucket seats are facing toward you (see Figure 9).
Figure 8
Figure 9
① 将安装好卡扣的外观框放在橱柜上作出比对；用记号笔画上安
装位置
② 用1#螺丝将卡座安装在对应安装位置上
①
Use 2# screws to install the four buckles on the corresponding mounting
holes around the trim kit 使用 2#螺丝将四个卡扣安装在外观框四周对
应的安装孔上
Place the trim kit which install buckle on the cabinet for
contrast, then use marker strokes to draw the mounting
position
① 将安装好卡扣的外观框放在橱柜上作出比对；用记号笔画上安
装位置
② 用1#螺丝将卡座安装在对应安装位置上
①
Use 2# screws to install the four buckles on the corresponding mounting
holes around the trim kit 使用 2#螺丝将四个卡扣安装在外观框四周对
应的安装孔上
Place the trim kit which install buckle on the cabinet for
contrast, then use marker strokes to draw the mounting
position
INSTALLATION
6
Trim Kit Installation
5. Using two people, lift the microwave and push it into the cabinet until the two
small lips in the rear bracket slide into both holes in the rear of the support beams
fastened in Step 1 to the bottom of the cutout (see Figure 10).
6. Use the two #3 screws to fasten the front bracket to the front of both support
beams (see Figure 11). The microwave should now be firmly secured inside the
cabinet cutout (see Figure 12).
Figure 10
Figure 11
Figure 12
INSTALLATION
7
Trim Kit Installation
7. Insert the outer trim kit into the cutout (see Figure 13). Clip each buckle onto its
corresponding buckle seat to complete the trim kit installation (see Figure 14).
① Insert the trim kit into the corresponding buckle seat 将
预装好外观框卡进对应卡扣座里
Finish
Figure 14
Figure 13
INSTALLATION
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
ZLINE MWDZ1BSHG User manual
- Type
- User manual
- This manual is also suitable for
ZLINE MWDZ1BSHG is a sleek and functional microwave drawer that combines convenience and style. It features a spacious 1.2 cubic feet capacity, allowing you to easily heat or cook a variety of dishes. With 10 power levels and a variety of preset cooking options, you can customize your cooking to perfection. The microwave also includes a child lock feature for added safety.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
ZLINE Kitchen and Bath MWD-TK-30 User manual
-
ZLINE KITCHEN & BATH MWD-TK-30 User manual
-
ZLINE RBIV-30 User manual
-
ZLINE Dual Built-In Refrigerator User manual
-
ZLINE AWDZ30BSG User manual
-
ZLINE Kitchen and Bath 2PCEXT-687-304 Owner's manual
-
ZLINE Monument Dishwasher User manual
-
ZLINE KITCHEN & BATH 355WHRD36 Owner's manual
-
-
Other documents
-
ZLINE Kitchen and Bath 8654STX-BM-48 Installation guide
-
ZLINE KITCHEN & BATH 697-RS-30-400 User manual
-
ZLINE Kitchen and Bath 8685S-30 User manual
-
-
-
-
-
-
ZLINE Kitchen and Bath 721-58 Installation guide
-
ZLINE KITCHEN & BATH DW7714-18 User guide
