Minka Group 5036-66A User manual

Brand: Minka Group

Model: 5036-66A

Type: User manual

INSTALLATION INSTRUCTIONS

Item#5036-66A (New. 02/27/2023)

READ AND SAVE THESE INSTRUCTIONS

WA R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .

AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

Fig. 1

Fig. 3

Fig. 2

Fig. 4

ASSEMBLING THE FIXTURE (

ig. 1

& Fig. 4

)

1. Shut off power at the fuse box or circuit breaker

box and remove

the old fixture, including mounting hardware.

2. Carefully unpack your new fixture from

carton and check that all

parts are included as shown in the illustration.

3. Adjust arms to proper position. (Fig.4)

4. Determine the desired hanging height and thread rods (B &

to coupling (D)，carefully feed wires through each rod

as you

assemble.

5. Attach fixture loop (A) by threading onto rod (B).

6. Attach cap (F) with screws (G) to hole (E) of fixture.

HANGING THE FIXTURE (Fig. 2)

7. Thread all thread into ceiling loop until snug.

8. Thread other end of all thread into crossbar, then use

lock

washer and hex nut to secure all thread into the crossbar.

Note:

The length of all thread into crossbar may

be adjusted if

necessary.

9. Take the crossbar assembly and mount it to ceiling outlet box

(Not included) with mounting screws (Size: #8-32N*L1”)

. The

side of crossbar marked with “GND” must face out.

10. Slide lock collar and canopy over rods and allow them to rest on

fixture body.

11. Open quick link and attach it to fixture loop and ceiling loop

then close quick link.

12. Carefully feed wires through quick link, ceiling loop and

all

thread assembly.

CONNECTING THE WIRE (Fig. 3)

13. Connect the electrical wire as shown in Fig. 3,

making sure that

all wire connectors are secured. If your outlet box

has a ground

wire (green or bare copper), connect fixtures ground

wire to it.

Otherwise, connect fixture ground wire directly to

crossbar using

green screw provided.

14. Tuck wire connections neatly into the outlet

box and then raise

canopy all the way to the ceiling.

15. Raise lock collar and thread onto ceiling loop

protruding through

canopy.

FINISHING THE FIXTURE (Fig.1)

16. Install (3) three candelabra base bulbs (H) up to 60 watts

each

or CFL or LED equivalent (not included) in accordance with the

fixture specification —

DO NOT EXCEED THE MAXIMUM

WATTAGE RATING! (

NE PAS DEPASSER LA PUISSANCE

NOMINALE MAXIMALE!).

Your installation is now complete. Return power to the

outlet

box and test the fixture.

Note: Illustration (Fig. 1) on this manual is for installa

tion

purposes only. It may or may not be identical to

the

fixture purchased.

5036-66A

FIXTURE

WIRES

Black or

Smooth

HOUSE

WIRES

Black

(Hot)

FIXTURE

WIRES

White or

Ribbed

HOUSE

WIRES

White

(Neutral)

FIXTURE

WIRES

Bare

Copper

(Ground)

USE

WIRES

Green

(Ground)

Set

010

-Crossbar

-Ground Screw

-Mounting Screw *2

Candle Cover# CCV21070P-66A

6” Tube# W30-H-66A

12” Tube# W30-1-66A

Lock Collar

Ceiling loop

Quick link

Canopy

Outlet box

Hex Nut

wire

Fixture loop

Minka Group 5036-66A User manual

Minka Group 5036-66A User manual

Minka Group 5036-66A User manual

Related papers

Other documents