Pipishell PISM02 User manual

Brand: Pipishell

Model: PISM02

Type: User manual

Soundbar Bracket

INSTRUCTION

MANUAL

Rev02(A)

PISM02

(US/CA) 1-800-556-9829

(UK) 44-808-196-3885

[email protected]

WWW. www.pipishellav.com

Before getting started,

let's make sure this mount is compatible.

22 lbs

（10kg）

Yes - Perfect!

No - This mount is NOT

compatible.

Yes - Perfect!

No -This mount is NOT compatible.

Is the VESA

pattern of your TV

75 x 75mm (3" x 3")

to 600 x 400mm

(23.6" x 15.7") ?

Does the equip-

ment you intend to use

weigh less than 22 lbs

(10kg) ?

Tools Needed

(NOT lncluded)

Important Safety

Information

· Avoid potential injuries and property damage!

· DO NOT use this product for any purpose that is NOT explicitly

speciﬁed in this manual. DO NOT exceed weight capacity. We are NOT

liable for damage or injury caused by improper mounting, incorrect

assembly or inappropriate use.

· Before starting assembly, verify all parts are included and undam-

aged. DO NOT use damaged or defective parts. lf you require replace-

ment parts, please contact our Technical Support line at

1-800-556-9829 (US/CA) / 44-808-196-3885 (UK) or Customer

Service at [email protected].

CAUTION

· This product contains small parts that may pose a choking hazard.

· This soundbar bracket is designed to be installed and utilized only as

speciﬁed in this manual.

· This soundbar bracket is ONLY designed to mount BELOW the

television.

WARNING

NOTE

· Please read and understand these directions.

· Refer to the documentation that came with your soundbar, your TV and

your TV wall mount for additional guidance.

· Carefull read all instructions before attempting installation. If you DO

NOT understand the instructions or have any questions or concerns, please

contact our Technical Support line at 1-800-556-9829 (US/CA) /

44-808-196-3885 (UK) or Customer Service at [email protected].

· Not all hardware included in this package will be used.

Phillips

Screwdriver

Contents

Hardware for Attaching the Brackets to the TV

[B1] x 4

[B2] x 4

L2.5mm

[F1] x 4

L22mm

[F2] x 4

Washers

Spacers

M8 x 30mm

[E1] x 4

M8 x 50mm

[E3] x 4

M8 x 65mm

[E4] x 4

M6 x 30mm

[D1] x 4

M4 x 30mm

[C1] x 4

M4 x 50mm

[C2] x 4

M6 x 50mm

[D2] x 4

M8 x 40mm

[E2] x 4

TV Bolts

Hardware for Attaching the Brackets to the Soundbar

Soundbar Bolts

Keyhole Screw

[g] x 2

Knob

[h] x 2

[d] x 2

[e] x 2

[f] x 2

M4 M4 x 10mm

[a1] x 2

Washers

M5 x 16mm

[b] x 4

M6 x 16mm

[c] x 4

M4 x 16mm

[a2] x 4

Vertical Bracket

01 x 1

Bracket

04 x 2

Connecting Rod

03 x 2

Vertical Bracket

02 x 1

Clamp

05 x 2

CAUTION: Follow your TV mount’s manual for instructions on how to

safely remove your TV and TV bracket.

NOTE: Your TV wall mount may vary from the illustrations throughout

this manual — the procedure to install the soundbar is the same.

a. If your TV brackets ﬁt inside the

vertical soundbar brackets, follow

Figure a.

b. If your TV brackets do not ﬁt

inside the vertical soundbar

brackets, follow Figure b.

Step 1 Prepare your TV [If mounted]

a b

1 2

TOSS

2-2 Spacer and Bolt Conﬁgurations

2-1 Select TV Bolts

Hand thread bolts into the threaded inserts on the back of your TV to determine which

bolt (M4, M6 or M8) to use. A minimum of 4-5 turns into the threading is required. Do

not turn past the bottom of the hole.

Step 2 Attach the TV Brackets and Vertical Brackets to the TV

M6 M8

Bump

See Option C

Curved TV

See Option B

Cables

See Option D

Recessed Holes

See Option E

Flat Back TV

See Option A

2-3 Attach the TV Brackets and Vertical Brackets to Your TV

Add spacers if needed to ﬁt the bolt length and TV back.

Option A: For Flat Back TVs

(If needed)

B1/B2

F1/F2

C1/D1/E1

0102

Knob facing

outward

0201

Knob facing

outward

0201

Option C: For TVs with a Bump

Option B: For Curved TVs

Spacers must be tall enough so that the curved back of the TV

does not interfere with the mounting plate.

The TV brackets must be ﬂush on the bump and leveled by spacers over the gap.

B1/B2

F1/F2

C2/D2/E2

/E3/E4

(If needed)

B1/B2

C1/D1/E1

B1/B2

F1/F2

C2/D2/E2

/E3/E4

Option E: For TVs with Recessed Holes

Option D: For TVs with Protruding Cables

Spacers [F1], [F2] need to ﬁll in the recessed holes on the back of the TV, while

keeping the TV brackets as close to the TV as possible.

Use spacers [F1] or [F2] to create extra space between the TV and TV brackets.

B1/B2

C2/D2/E2

/E3/E4

F1/F2

B1/B2

C2/D2/E2

/E3/E4

F1/F2

3-1 Slightly loosen the knobs on both vertical brackets.

3-2 Insert the connecting rods [03] into the vertical brackets, then slide the brackets

[04] onto the connecting rods. Do not secure them before choosing the soundbar

bracket conﬁguration on Page 11.

Step 3 Assemble the Bottom Brackets

Phillips

Screwdriver

(Not lncluded)

3-3 Measure the distance between the mounting holes on your soundbar / width of

your soundbar.

3-4 Based on your soundbar measurements, choose a proper bracket conﬁguration

(See following ﬁgures.)

Back-Mounted Keyhole Slots

Soundbar Width

Phillips

Screwdriver

(Not lncluded)

3-5 Retighten the knobs, and secure the

brackets [04] with washers [d] and bolts [b].

Bottom-Mounted Threaded Inserts

Page 12

Page 13 - 14

Step 4 Attach the Soundbar (Not Included)

Option A: For soundbar with back-mounted keyhole slots

Insert the keyhole screws [g] into the keyholes on the back of the soundbar, then

secure to the mount with knobs [h] and washers [f].

A: For soundbar with back-mounted keyhole slots, follow the instruction on page 12.

B: For soundbar without any mounting holes or with bottom-mounted threaded inserts,

go to page 13 and 14.

Option B: For soundbar without any mounting holes or with bottom-

mounted threaded inserts

Slightly loosen the bolts underneath to extend the clamps.

Turn over the TV. Hang the clamps onto the brackets, making sure the hooks ﬁt over

the brackets.

Phillips

Screwdriver

(Not lncluded)

Phillips

Screwdriver

(Not lncluded)

Place soundbar on the clamps, then adjust the

clamps to ﬁt and secure by retightening the

bolts. Also, tighten the bolts securing the clamps.

Phillips

Screwdriver

(Not lncluded)

Step 5 Adjust the Soundbar Height (Optional)

NOTE: Depending on the type of TV wall mount you have, you may need to

remove your TV from the wall to adjust the soundbar height.

CAUTION: Make sure to support your soundbar with one hand while moving it.

860-00538-00 Rev02 16

Step 6 Reattach the TV

Pipishell PISM02 User manual

Brand: Pipishell

Model: PISM02

Type: User manual

Download PDF

report

Pipishell PISM02 User manual

Pipishell PISM02 User manual

Related papers

Other documents