MICRO-MARK Micro-Mark 82088 Gourd Cross Saw Operating instructions

Type
Operating instructions

MICRO-MARK Micro-Mark 82088 Gourd Cross Saw is a versatile tool designed for precise cutting of wood, plastic, and thin metal. With its compact size and 12V DC power source, it offers portability and convenience. The saw features a quick-change chuck system that allows for easy blade replacement, and the included Allen wrench ensures secure blade tightening. For optimal performance, the instruction manual recommends using optional fine saw blades (#15244) for smoother cuts, especially when working with metal or thin wood.

MICRO-MARK Micro-Mark 82088 Gourd Cross Saw is a versatile tool designed for precise cutting of wood, plastic, and thin metal. With its compact size and 12V DC power source, it offers portability and convenience. The saw features a quick-change chuck system that allows for easy blade replacement, and the included Allen wrench ensures secure blade tightening. For optimal performance, the instruction manual recommends using optional fine saw blades (#15244) for smoother cuts, especially when working with metal or thin wood.

MM122716
Operating Instructions for #82088 Cross Saw
1. Use your Cross Saw with a 12 volt DC power source only.
2. To change saw blade, unplug tool and loosen chuck with Allen wrench
supplied. Insert saw blade with teeth facing forward. NEVER TIGHTEN
CHUCK WITHOUT A SAW BLADE INSERTED. ALWAYS TIGHTEN
CHUCK FROM THE SIDE, NEVER THE FRONT.
3. If blade cannot be inserted into slot, remove chuck, check for debris
in the slot and clean out as necessary. Open slot slightly with a fine
screwdriver until blade can be inserted easily, but not too much, which
would prevent reinstallation of chuck. Reassemble unit.
4.
Saw blades furnished with Cross Saw are for cutting wood or plastic only.
For a smoother
cut, or for cutting metal or very thin wood, order optional
fine saw blades #15244.
CAUTION
Always unplug tool before changing saw blades.
Secure work. Use clamps or a vise to hold work whenever possible.
Change saw blades as soon as wear is apparent.
Wear eye protection.
Do not operate tool after taking drugs, alcohol or medications or when tired or fatigued.
Keep long hair tied back.
Do not wear loose clothing.
340 Snyder Avenue
Berkeley Heights, NJ 07922
Tech Support: T[email protected] • www.micromark.com MM122716
Operating Instructions for #82088 Cross Saw
1. Use your Cross Saw with a 12 volt DC power source only.
2. To change saw blade, unplug tool and loosen chuck with Allen wrench
supplied. Insert saw blade with teeth facing forward. NEVER TIGHTEN
CHUCK WITHOUT A SAW BLADE INSERTED. ALWAYS TIGHTEN
CHUCK FROM THE SIDE, NEVER THE FRONT.
3. If blade cannot be inserted into slot, remove chuck, check for debris
in the slot and clean out as necessary. Open slot slightly with a fine
screwdriver until blade can be inserted easily, but not too much, which
would prevent reinstallation of chuck. Reassemble unit.
4.
Saw blades furnished with Cross Saw are for cutting wood or plastic only.
For a smoother
cut, or for cutting metal or very thin wood, order optional
fine saw blades #15244.
CAUTION
Always unplug tool before changing saw blades.
Secure work. Use clamps or a vise to hold work whenever possible.
Change saw blades as soon as wear is apparent.
Wear eye protection.
Do not operate tool after taking drugs, alcohol or medications or when tired or fatigued.
Keep long hair tied back.
Do not wear loose clothing.
340 Snyder Avenue
Berkeley Heights, NJ 07922
Tech Support: T[email protected] • www.micromark.com
MM122716
Operating Instructions for #82088 Cross Saw
1. Use your Cross Saw with a 12 volt DC power source only.
2. To change saw blade, unplug tool and loosen chuck with Allen wrench
supplied. Insert saw blade with teeth facing forward. NEVER TIGHTEN
CHUCK WITHOUT A SAW BLADE INSERTED. ALWAYS TIGHTEN
CHUCK FROM THE SIDE, NEVER THE FRONT.
3. If blade cannot be inserted into slot, remove chuck, check for debris
in the slot and clean out as necessary. Open slot slightly with a fine
screwdriver until blade can be inserted easily, but not too much, which
would prevent reinstallation of chuck. Reassemble unit.
4.
Saw blades furnished with Cross Saw are for cutting wood or plastic only.
For a smoother
cut, or for cutting metal or very thin wood, order optional
fine saw blades #15244.
CAUTION
Always unplug tool before changing saw blades.
Secure work. Use clamps or a vise to hold work whenever possible.
Change saw blades as soon as wear is apparent.
Wear eye protection.
Do not operate tool after taking drugs, alcohol or medications or when tired or fatigued.
Keep long hair tied back.
Do not wear loose clothing.
340 Snyder Avenue
Berkeley Heights, NJ 07922
Tech Support: T[email protected] • www.micromark.com MM122716
Operating Instructions for #82088 Cross Saw
1. Use your Cross Saw with a 12 volt DC power source only.
2. To change saw blade, unplug tool and loosen chuck with Allen wrench
supplied. Insert saw blade with teeth facing forward. NEVER TIGHTEN
CHUCK WITHOUT A SAW BLADE INSERTED. ALWAYS TIGHTEN
CHUCK FROM THE SIDE, NEVER THE FRONT.
3. If blade cannot be inserted into slot, remove chuck, check for debris
in the slot and clean out as necessary. Open slot slightly with a fine
screwdriver until blade can be inserted easily, but not too much, which
would prevent reinstallation of chuck. Reassemble unit.
4.
Saw blades furnished with Cross Saw are for cutting wood or plastic only.
For a smoother
cut, or for cutting metal or very thin wood, order optional
fine saw blades #15244.
CAUTION
Always unplug tool before changing saw blades.
Secure work. Use clamps or a vise to hold work whenever possible.
Change saw blades as soon as wear is apparent.
Wear eye protection.
Do not operate tool after taking drugs, alcohol or medications or when tired or fatigued.
Keep long hair tied back.
Do not wear loose clothing.
340 Snyder Avenue
Berkeley Heights, NJ 07922
Tech Support: T[email protected] • www.micromark.com
MM122716
Operating Instructions for #82088 Cross Saw
1. Use your Cross Saw with a 12 volt DC power source only.
2. To change saw blade, unplug tool and loosen chuck with Allen wrench
supplied. Insert saw blade with teeth facing forward. NEVER TIGHTEN
CHUCK WITHOUT A SAW BLADE INSERTED. ALWAYS TIGHTEN
CHUCK FROM THE SIDE, NEVER THE FRONT.
3. If blade cannot be inserted into slot, remove chuck, check for debris
in the slot and clean out as necessary. Open slot slightly with a fine
screwdriver until blade can be inserted easily, but not too much, which
would prevent reinstallation of chuck. Reassemble unit.
4.
Saw blades furnished with Cross Saw are for cutting wood or plastic only.
For a smoother
cut, or for cutting metal or very thin wood, order optional
fine saw blades #15244.
CAUTION
Always unplug tool before changing saw blades.
Secure work. Use clamps or a vise to hold work whenever possible.
Change saw blades as soon as wear is apparent.
Wear eye protection.
Do not operate tool after taking drugs, alcohol or medications or when tired or fatigued.
Keep long hair tied back.
Do not wear loose clothing.
340 Snyder Avenue
Berkeley Heights, NJ 07922
Tech Support: T[email protected] • www.micromark.com MM122716
Operating Instructions for #82088 Cross Saw
1. Use your Cross Saw with a 12 volt DC power source only.
2. To change saw blade, unplug tool and loosen chuck with Allen wrench
supplied. Insert saw blade with teeth facing forward. NEVER TIGHTEN
CHUCK WITHOUT A SAW BLADE INSERTED. ALWAYS TIGHTEN
CHUCK FROM THE SIDE, NEVER THE FRONT.
3. If blade cannot be inserted into slot, remove chuck, check for debris
in the slot and clean out as necessary. Open slot slightly with a fine
screwdriver until blade can be inserted easily, but not too much, which
would prevent reinstallation of chuck. Reassemble unit.
4.
Saw blades furnished with Cross Saw are for cutting wood or plastic only.
For a smoother
cut, or for cutting metal or very thin wood, order optional
fine saw blades #15244.
CAUTION
Always unplug tool before changing saw blades.
Secure work. Use clamps or a vise to hold work whenever possible.
Change saw blades as soon as wear is apparent.
Wear eye protection.
Do not operate tool after taking drugs, alcohol or medications or when tired or fatigued.
Keep long hair tied back.
Do not wear loose clothing.
340 Snyder Avenue
Berkeley Heights, NJ 07922
Tech Support: T[email protected] • www.micromark.com
  • Page 1 1

MICRO-MARK Micro-Mark 82088 Gourd Cross Saw Operating instructions

Type
Operating instructions

MICRO-MARK Micro-Mark 82088 Gourd Cross Saw is a versatile tool designed for precise cutting of wood, plastic, and thin metal. With its compact size and 12V DC power source, it offers portability and convenience. The saw features a quick-change chuck system that allows for easy blade replacement, and the included Allen wrench ensures secure blade tightening. For optimal performance, the instruction manual recommends using optional fine saw blades (#15244) for smoother cuts, especially when working with metal or thin wood.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI